Schneider Electric Enerlin’X FDM121 Front Display Module for One Circuit Breaker Owner’s Manual
- June 10, 2024
- Schneider Electric
Table of Contents
TRV00121
Enerlin’X FDM121 Front Display
Module for One Circuit Breaker
Owner’s Manual
Enerlin’X FDM121 Front Display Module for One Circuit Breaker
QGH80971-03http://download.schneider- electric.com/files?p_Doc_Ref=QGH80971
| www.se.com
---|---
| FDM121| ULP System
| DOCA0088EN| DOCA0093EN
| 0602IB1503
Retain instruction sheet for future use.
Visit our website at www.se.com to download the
documents listed above (user guides ) and other documents.
PLEASE NOTE
- Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel.
- No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material.
- All pertinent state, regional, and local safety regulations must be observed when installing and using this product.
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
-
Only qualified workers should install this equipment. Such work should be performed only after reading this entire set of instructions.
-
NEVER work alone.
-
Before performing visual inspections, tests, or maintenance on this equipment, disconnect all sources of electric power.
Assume that all circuits are live until they have been completely deenergized, tested, and tagged. Pay particular attention to the design of the power system. Consider all sources of power, including the possibility of backfeeding. -
Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices. See NFPA 70E, CSA Z462, NOM-029-STPS or local equivalent.
-
Turn off all power supplying the equipment in which the FDM121 display is to be installed before installing and wiring the FDM121 display.
-
Always use a properly rated voltage sensing device to confirm that power is off.
-
Beware of potential hazards, and carefully inspect the work area for tools and objects that may have been left inside the equipment.
Failure to follow these instructions will result in death or serious
injury.
**WARNING:** This product can expose you to chemicals including Diisononyl
Phthalate (DINP), which is known to the State of Califomia to cause cancer and
Diisodecyl Phthalate (DIDP) which is known to the State of California to cause
birth defects or other reproductive harm.
For more information go to
www.P65Warnings.ca.gov.
Required for Installation
Description
A Alarm indicator LED
- steady off: nominal operation
- blinking: high priority alarm
- steady on: medium priority alarm
B LCD screen
C Navigation keys
D Functional ground
E 2 RJ45 ULP ports
F 24 Vdc power supply terminal block
Dimensions
Installation
4.1 Door Cutout Mounting
4.2 Hole
Mounting
24 Vdc Power Supply
ULP Connection
NOTICE
HAZARD OF EQUIPMENT DAMAGE
- Never connect a Modbus-SL device to a ULP RJ45 port.
- The FDM121 display ULP RJ45 ports, are for ULP modules only.
- Any other use can damage the FDM121 display or the device connected to the FDM121 display.
- To check if a ULP module is compatible with the FDM121 display’s ULP RJ45 ports, refer to the ULP system user guide.
Failure to follow these instructions can result in equipment
damage.
Communication Architecture
A FDM128 (LV434128)
B FDM121 (TRV00121)
C IFE (LV434001)
D IFE server (LV434002)
E IFM (TRV00210)
F IO (LV434063)| G Drawout MasterPact MTZ1/MTZ2/MTZ3
H Fixed MasterPact MTZ1/MTZ2/MTZ3
I MasterPact NT/NW
J ComPacT NS630b-3200 / PowerPacT P-, R-Frame
K ComPacT NSX / PowerPacT H-, J-, L-Frame
L ULP port module| M EIFE (LV851001)
N ULP line termination (TRV00880)
—- O ULP cord —- Ethernet
—- P BCM ULP cord —- Modbus-SL
Q NSX cord
---|---|---
Commissioning
- Connect the intelligent modular unit (IMU) modules together.
- Supply the IMU communication interface with 24 Vdc.
- Press the IO module Test/Reset button for 1 to 5 seconds.
- Check that all the ULP modules in the IMU react:
• the ULP status LED flashes on the IO module, on the IFM or IFE
• the screen flashes for 15 seconds on the FDM121 display, on the MicroLogic 5/6/7 trip units in the ComPacT NSX and PowerPacT H-, J-, L-frame circuit breaker, on the MicroLogic P/H trip units in the MasterPact NT/NW, ComPacT NS and PowerPacT P-, R-frame circuit breakers, and on the MicroLogic X trip units in the MasterPact MTZ circuit breaker.
Note: The screen of the MicroLogic A/E trip units in the MasterPact
NT/NW, ComPacT NS and PowerPacT P-, R-frame circuit breakers does not flash
during this check.
Schneider Electric Industries SAS
35, rue Joseph Monier
CS 30323
F – 92506 Rueil Malmaison Cedex
www.se.com
QGH80971-03
Printed on recycled paper.
© 2022 Schneider Electric – All rights reserved.
Schneider Electric Limited
Stafford Park 5
Telford, TF3 3BL
United Kingdom
www.se.com/uk
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>