Schneider Electric PacT Series Offers World Class Breakers and Switches User Guide

: October 27, 2023
: Schneider Electric

Table of Contents

Schneider Electric PacT Series Offers World Class Breakers and Switches
Legal Information
About the Book
Introduction to Service Interface
Firmware Versions
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Schneider Electric PacT Series Offers World Class Breakers and Switches

Legal Information

The Schneider Electric brand and any trademarks of Schneider Electric SE and its subsidiaries referred to in this guide are the property of Schneider Electric SE or its subsidiaries. All other brands may be trademarks of their respective owners.
This guide and its content are protected under applicable copyright laws and furnished for informational use only. No part of this guide may be reproduced or transmitted in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), for any purpose, without the prior written permission of Schneider Electric.
Schneider Electric does not grant any right or license for commercial use of the guide or its content, except for a non-exclusive and personal license to consult it on an “as is” basis. Schneider Electric products and equipment should be installed, operated, serviced, and maintained only by qualified personnel.
As standards, specifications, and designs change from time to time, information contained in this guide may be subject to change without notice.
To the extent permitted by applicable law, no responsibility or liability is assumed by Schneider Electric and its subsidiaries for any errors or omissions in the informational content of this material or consequences arising out of or resulting from the use of the information contained herein.
As part of a group of responsible, inclusive companies, we are updating our communications that contain non-inclusive terminology. Until we complete this process, however, our content may still contain standardized industry terms that may be deemed inappropriate by our customers.

About the Book

PacT Series Master Range
Future-proof your installation with Schneider Electric’s low-voltage and medium voltage PacT Series. Built on legendary Schneider Electric innovation, the PacT Series comprises world-class circuit breakers, switches, residual current devices and fuses, for all standard and specific applications. Experience robust performance with PacT Series within the Eco Struxure-ready switchgear, from 16 to 6300 A in low-voltage and up to 40.5 kV in medium- voltage.

Document Scope
This document provides you with the firmware version history of Service Interface.
Use this document to determine whether an update to the latest version of the Service Interface is interesting or relevant for your application.

Validity Note
This document applies to Service Interface used with Micro Logic™ trip units mounted in the following low voltage circuit breakers:

MasterPact™ NT/NW circuit breakers
EasyPact™ MVS circuit breakers
ComPacT™ NS circuit breakers
PowerPacT™ P- and R- frame circuit breakers
ComPacT™ NSX circuit breakers
PowerPacT™ H-, J-, and L-frame circuit breakers
NOTE:
The information related to the new generation of ComPacT NSX and PowerPacT H-, J-, and L-frame circuit breakers in this guide applies to the existing range ComPact NSX and PowerPact H-, J-, and L-frame circuit breakers also. The exceptions are mentioned wherever applicable.
The information related to the new generation of ComPacT NS and PowerPacT P- and R-frame circuit breakers in this guide applies to the existing range ComPact NS and PowerPact P- and R-frame circuit breakers also. The exceptions are mentioned wherever applicable.

Related Documents for IEC Devices
The following table lists documents for IEC devices compatible with the Service Interface with the latest firmware version.

Title of documentation	Reference number
Service Interface – User Guide

DOCA0170EN
MasterPact NT – Circuit Breakers and Switch-Disconnectors from 630 to 1600 A – User Guide| 51201116AA (EN)
MasterPact NW – Circuit Breakers and Switch-Disconnectors from 800 to 6300 A – User Guide| 04443720AA (EN)
MasterPact NT/NW – Circuit Breakers and Switch-Disconnectors – Maintenance Guide| LVPED508016EN
MasterPact NT/NW – Basic and Standard End-User Maintenance Procedures| HRB16483EN
ComPacT NS – MicroLogic Trip Units – User Guide| DOCA0217EN

Service Interface for MasterPact NT/NW, ComPacT, PowerPacT, and EasyPact Circuit Breakers

Title of documentation	Reference number
ComPacT NS – MicroLogic A/E Trip Units – User Guide

DOCA0218EN
ComPacT NS – MicroLogic P Trip Units – User Guide| DOCA0219EN
ComPacT NS – Circuit Breakers and Switch-Disconnectors – User Guide| DOCA0221EN
ComPacT NSX – Circuit Breakers and Switch-Disconnectors – User Guide| DOCA0187EN
ComPacT NSX – MicroLogic 5/6/7 Electronic Trip Units – User Guide| DOCA0188EN
EasyPact MVS – User Manual| LVED311021EN

You can download these technical publications and other technical information from our website at www.se.com/ww/en/download.

Related Documents for UL Devices
The following table lists documents for UL devices compatible with the Service Interface with the latest firmware version.

Title of documentation	Reference number
Service Interface – User Guide

DOCA0170EN
MasterPact NT Low-Voltage Power/Insulated Case Circuit Breaker – Instruction Bulletin| 0613IB1209 (EN, ES, FR)
MasterPact NW Low-Voltage Power/Insulated Case Circuit Breaker – Instruction Bulletin| 0613IB1204 (EN, ES, FR)
PowerPacT R-Frame and NS1600b–NS3200 Circuit Breakers – Instruction Bulletin| 48049-243-04 (EN, ES, FR)
PowerPacT P-Frame and NS630b–NS1600 Circuit Breakers – Instruction Bulletin| 48049-148-05 (EN, ES, FR)
PowerPacT P-Frame Drawout Circuit Breakers – Instruction Bulletin| 48049-336-02 (EN, ES, FR)
PowerPacT H-, J-, and L-Frame Circuit Breakers with MicroLogic Trip Units – User Guide| 48940-313-01 (EN, ES, FR)

You can download these technical publications and other technical information from our website at www.se.com/ww/en/download.

Introduction to Service Interface

Overview

The Service Interface is a portable instrument designed for field testing. The Service Interface with part number LV485500 is used for testing and configuration of MicroLogic™ trip units mounted in the following low voltage circuit breakers:

MasterPact™ NT/NW circuit breakers
EasyPact™ MVS circuit breakers
ComPacT™ NS circuit breakers
PowerPacT™ P- and R- frame circuit breakers
ComPacT™ NSX circuit breakers
PowerPacT™ H-, J-, and L-frame circuit breakers
NOTE:
The information related to the new generation of ComPacT NSX and PowerPacT H-, J-, and L-frame circuit breakers in this guide applies to the existing range ComPact NSX and PowerPact H-, J-, and L-frame circuit breakers also. The exceptions are mentioned wherever applicable.
The information related to the new generation of ComPacT NS and PowerPacT P- and R-frame circuit breakers in this guide applies to the existing range ComPact NS and PowerPact P- and R-frame circuit breakers also. The exceptions are mentioned wherever applicable.
These new ranges are based on the same technical and dimensional architecture as that of the exiting range of circuit breakers.

EcoStruxure™ Power Commission (EPC) is a global software with test functions features for testing the circuit breakers and communication accessories through the Service Interface.

Firmware Release History

The following table indicates the release history of Service Interface firmware.

Date	Firmware version	Availability
April 2022	001.001.019	Digital release in EcoStruxure Power Commission

software
January 2022| 001.001.015| Obsolete
December 2021| 001.001.012| Obsolete
October 2021| 001.001.008| Obsolete
August 2021| 001.000.003| Obsolete
October 2020| 001.000.001| Obsolete
August 2020| 001.000.000| Obsolete

Firmware Update Policy

Firmware update is recommended to benefit from the latest features and potential bug fixes. Do not update the firmware to the latest version, if the latest features are not required for your application and no bug fixes are provided.
Use this release note to determine whether an update to the latest version of the firmware is relevant for your application.
For more information about the firmware update policy and the firmware compatibility between devices, refer to DOCA0155EN MicroLogic Trip Units and Control Units – Firmware History.

Firmware Update with EcoStruxure Power Commission Software

Use the latest version of EcoStruxure Power Commission software to:

Check the firmware compatibility of the devices in the IMU.
Update the devices with the latest firmware version available.

After updating the firmware of one device, use EcoStruxure Power Commission software to check the firmware compatibility between IMU devices.
The Firmware Update table helps the user to diagnose and identify all discrepancy issues between IMU devices. This table also provides the recommended actions for each discrepancy issue.
The latest version of EcoStruxure Power Commission software is available at www.se.com.
For more information about the use of EcoStruxure Power Commission software, refer to EcoStruxure Power Commission Online Help.

Firmware Versions

Firmware Version 001.001.019

New Features
The Service Interface can be used for testing and configuring the
MicroLogic 5 A/E, MicroLogic 6 A/E, and MicroLogic 7 E trip units mounted in the following low voltage circuit breakers:

ComPacT NSX circuit breakers
PowerPact H-, J-, and L-frame circuit breakers

Automatic trip curve test with pre-configured test points can be performed through the Service Interface.

Firmware Version 001.001.015

New Features

The Service Interface can be used for testing and configuring the MicroLogic 5.2 B and 5.3 B trip units mounted in the following low voltage circuit breakers:
- ComPacT NSX circuit breakers
- PowerPact H-, J-, and L-frame circuit breakers
  The following tests can be performed through the Service Interface:
- Automatic trip curve test with pre-configured test points
- Automatic trip curve test with custom test points
The Service Interface can be used for configuring the MicroLogic 5 A/E, 6 A/E, and 7 E trip units mounted in the following low voltage circuit breakers:
- ComPacT NSX circuit breakers
- PowerPact H-, J-, and L-frame circuit breakers

Firmware Version 001.001.012

Bugs Fixed
Automatic trip curve test did not trip MasterPact NW4000b–6300 circuit breakers. Bug introduced in firmware version 001.001.008.

Firmware Version 001.001.008

Bugs Fixed
During automatic trip curve test on MicroLogic trip unit:

Trip did not occur on the circuit breaker due to injection time out.
Trip occurred but the trip time was not displayed properly.

Firmware Version 001.000.003

Bugs Fixed

Algorithm was not able to support different Mitop coils.
EcoStruxure Power Commission register mapping was incorrect for the circuit breakers manufactured prior to 2007.

Firmware Version 001.000.001

Bugs Fixed
The Service Interface can be used for testing the following MicroLogic trip units:

non-communicating MicroLogic trip units
communicating MicroLogic A, E, P, and H trip units

when they are mounted in the following low voltage circuit breakers:

MasterPact NT/NW circuit breakers
EasyPact MVS circuit breakers
ComPacT NS circuit breakers
PowerPacT P- and R- frame circuit breakers

The following tests can be performed using the Service Interface:

Automatic trip curve tests
- with preconfigured test points
- with custom test points
Zone-Selective Interlocking (ZSI) test
Device check up (Force trip test)
Preparation for primary injection tests:
- Reset thermal memory
- Inhibit ground-fault protection

Schneider Electric