Studio Titan STA 01-350R-MK2 Rotating Commercial Studio Stand User Manual
- June 10, 2024
- Studio Titan
Table of Contents
Studio Titan STA 01-350R-MK2 Rotating Commercial Studio Stand
CAUTION: Use supplied leather work gloves and safety glasses when
handling the box, when opening the box, and when assembling the product.
HAZARD: Strapping is under tension and can jump when cut. Strapping and
Buckles, Protective Edging, Plastic Walls, Plastic Caps, and Product
Components and parts should be handled with care. Work slowly, and use extra
caution to avoid any sharp edges.
Additional Tools May be Required: The essential tools are included. The
following tools are recommended to be on site: Box Cutter, Scissors, Screw
Driver, Plyers or Adjustable wrench, Metric Hex / Allen Key set
WARNING
TO AVOID THE DANGER OF SUFFOCATION, KEEP PLASTIC BAGS SUPPLIED WITH THIS
PRODUCT AWAY FROM BABIES AND CHILDREN!
Transit Damage:
Each package is inspected prior to being shipped from the warehouse to ensure
that is in perfect condition. The column shipping boxes are constructed using
extra-thick cardboard. Some packaging includes engineered plastic walls, end
caps, and banding. The columns are packed using engineered plastic walls and
in dense foam to protect and absorb energy from reasonable drops and impacts.
The column packaging is designed and drops tested from approximately 5 feet
[1.5 Me-ters] without sustaining any internal damage. The packaging is crush
tested using a 660lb [300kg] weight placed along the long side of the box
without sustaining any internal damage. If handled without care the boxes will
show signs of transit damage. Wearing supplied work Gloves, while following
the Assembly Steps, carefully inspect the contents inside the boxes.
Specifically, the Vertical center column top cap pulley should be securely
fastened to the top of the Vertical center column as shown on the [component
identification] page. In the base, the transportation counterweight securing
strap should be secured to the counterweight. [See Diagram: E] If anything
seems unusual, !!!STOP!!! Send images to: in-
fo@studiotitanamerica.com for a second
opinion. If there are damaged OR Loose parts, do not assemble the stand, you
may injure yourself. If the damage is noticeable such as cracks or loose or
broken parts contact your dealer for exchange. If the damage is minor or
cosmetic and does not compromise the safe assembly or operation of the stand
send images of the parts that are affected to:
info@studiotitanamerica.com.
Arrangements will be made to provide you with replacement parts to restore the
stand to new condition.
The product Nameplate / Label is located on the vertical column assembly. The
label information is indicated below:
STUDIO TITAN AMERICA
- No. [Model Number] – [Manufacture Date]
- Imported by / Importe par
- STEPHANIE MCNEIL CORPORATION
- 250 Augusta Ave, Suite 204
- Toronto, ON M5T 2L7 CANADA
- Manufactured in / Fabrique en
- SOUTH KOREA
Label examples are indicated below
Intended use:
This product is intended for use by professional and commercial photographers
in a studio envi-ronment with a high ceiling. The wheels are designed to be
used indoors on a floor that is smooth, hard, flat, and unobstructed. The
Studio Stands with internal counterweights are designed to be used at all
times with a load (Camera or laptop shelf or both).
CAUTION: This product is not recommended for use by hobbyists or in a household environment with a low ceiling or carpeted floors. Carpeting or pitted surfaces are not recommended because of the increased rolling resistance which can cause the stand to tip over. If the surface is not ideal, the stand must be moved with
CAUTION, very slowly, using both hands one at the top and the other at the bottom to steady the stand in order to prevent the stand from tipping over. If the surface is not ideal, lower the load to the waist level before moving the stand. We also recommend the use of a sandbag or weight attached at the base when conditions are not ideal to prevent tipping over. Ultimately it’s the user’s responsibility to understand how the stand operates and to use the stand within its specification limits, as intended to ensure their own safety and the safety of their equipment. It is also recommended to use a short tether cable to secure the camera to the stand in the event that the head, head plate, attachment stud, or camera adapter plate comes loose or fails. Some assembly is required, we recommend using an assistant during the initial product assembly. Please read all documentation prior to assembly.
Component Identification: STA 01-350R-MK2
Component
Identification: STA 01-350R-MK2
CAUTION! Cross Threading Components:
Cross-threading components during assembly is not covered under war- ranty.
Cross-threading is a term that describes the damage that is caused when a misaligned screw or knob thread is forced into a threaded hole. When this occurs, threads are damaged and are no longer capable of proper opera-tion. The remedy is the replacement or repair of the damaged component/s. AVOID cross-threading of mounting screws and knobs during assembly using this easy- to-follow procedure: While standing in front of and looking into the threaded hole. Place the screw or knob thread against the threaded hole. Using one hand, hold the thread between your fingers. With the other hand hold the hex key like a pencil or place your index finger in the center of the knob. Align the screw or knob with the hole as indicated in the picture with the checkmark below. Slowly turn it counter-clockwise or left, several turns, until you hear a click or feel the start of the thread. Then proceed slowly, turning clockwise or right, gently using only finger force to tighten the screw or knob. If you feel increased resistance, and the threads are not aligned, remove and start the procedure from the beginning again.
Component Identification: STA 01-350R-MK2
Component Identification: STA 01-350R-MK2
WARNING
READ ALL INSTRUCTIONS PRIOR TO ASSEMBLY AND OPERATION
Component Identification: STA 01-350R-MK2
Hand Lever adjustable, 360 degree range of movement, camera head mount plates
Assembly Steps:
- Wearing gloves and together with your Assistant……..Place the Column Box [long rectangular box] flat on the floor. Place some packing materials on the floor. Do not stand the Vertical/Center Column vertically. Remove and Lay the Vertical/Center Column flat on the floor. Under the Base, Visually inspect and Confirm that the Counter-weight transport securing SCREW is present which secures the counterweight during transportation. Do NOT remove the Counterweight transport securing SCREW until advised later. Confirm the bolt is present and proceed to step 2 with assembly. If NOT, then: If Counterweight transports securing SCREW is NOT present, the counterweight is loose and can move inside the column. Do not stand the column vertically. Stop the SET-UP and Contact STEPHA-NIE MCNEIL CORPORATION for further instruc-tions. Please email info@studiotitanamerica.com with the best phone number to reach you. We normally respond within 24hrs, during weekdays.
- Attach the three Leg Assemblies to the base. [See Diagram: A] Three fasteners are supplied and attached to each Leg Assembly. Use the supplied Hex Key tool to tighten the nine fasteners by hand. Attach the vibration reduction brackets to the legs using the Hex key tool and four fasteners lock washers & washers. Note: two of the leg assemblies are supplied with foot plungers. To have direct access to the foot plungers, install the foot plungers facing the operator or on the same side of the stand that the Horizontal and Vertical scales face.
- Wearing Gloves, remove the counterweight transportation securing SCREW [See Component Identification STA 01-350MK2 Diagram ]
- Locate and identify the counterweight cable.[See Component Identification STA 01-350MK2 Diagram ]
CAUTION AVOID CONTACT WITH THE COUNTERWEIGHT CABLE AT ALL TIMES. CAUTION MUST BE USED TO AVOID PINCHING YOUR FINGER DURING SET-UP AND NORMAL OPERA- TION. The counterweight cable may become frayed during transportation or normal use. When frayed, stop using the stand and immediately replace the cable. Cable strands that separate may become sharp.
Together with your Assistant…Wearing Gloves …..Carefully, Slowly raise and lift the Vertical/ Center Column until it is standing freely on its wheels.
- Locate the M8 Hex Wrench. Refer to the section “Cross Threading Components.” Remove the six M8 x 20 screws from the Vertical carriage. Two M8 screws from the front and two from each side. [Diagrams: B1&B2 indicate the screw locations] Locate the Horizontal Arm/Bar Carriage Assembly. [See Component Identification STA 01-350R Diagram] Together with your assistant. Have your assistant hold the Horizontal Arm/Bar Carriage Assembly in place while you fasten it with the six M8 x 20 screws. Note the order. [screw, spring washer and then flat washer] Hand tightening with the Hex Wrench is recommended. If you have a torque wrench tighten the M8 screws to 45Nm or 33 lb/ft. not more.
- Locate the M6 Hex Wrench. Refer to section “Cross Threading Components.” Locate the loose Vertical / Brake Knob. Find the Location of the Vertical Carriage / Brake Knob Transportation Set Screw. [See DIAGRAM: D]. With the M6 Hex Wrench FIRST Remove the transportation set screw and then replace it with a Vertical Carriage / Brake Knob. Turn the Vertical Carriage /Brake Knob fully Clock Wise to secure the vertical car- riage in the upper most or “parking position.” Locate the loose Rotational Knob / Brake. Refer to section “Cross Threading Components.” Insert and fasten the Rotational Knob / Brake into the Rota- tional carriage. [See DIAGRAM: E]
Component Identification: STA 01-350R-MK2
Component Identification: STA 01-350R-MK2
- Locate two M8 Hex wrenches. Locate the Basket. Locate the Basket Shaft. [See Component Identification STA 01-350R Diagram] Refer to the section “Cross Threading Components.” With the first M8 hex key hold the M8 screw at the top of the Basket shaft. With the second M8 hex key loosen the M8 screw at the bottom of the Basket shaft. Attach the Basket to the Basket Shaft. Note the order of fastener connection: [Screw, Flat washer, Basket Plate, Flat Washer]. [See: DIAGRAM: C]
- CAUTION: [Only with the Horizontal Arm/Bar in the uppermost position “parking position”.] Slowly release the Vertical Carriage Knob/brake by turning it Counter Clock Wise. This will release the vertical carriage allowing it to travel freely up and down the Vertical Center / Colum. Confirm that the Vertical Carriage is free to move in both directions while using both hands to hold the Horizontal Arm/Bar. Turn the Vertical Carriage Knob/brake fully Clock Wise to secure the vertical carriage.
- Locate the Two Horizontal Carriage Knob/ Brakes. [See Component Identification STA 01- 350R Diagram] Turn the Horizontal Carriage Knob/Brake Counter Clockwise to release and confirm that the Horizontal Arm / Bar is free to move left and right. STOP SET-UP— Read below— GO TO STEP 11 If anything seems unusual or if the vertical carriage is not moving freely up or down. Stop Set-up and send a few images of the stand to: info@studiotitanamerica.com for assistance.
Use & Maintenance
- HAZARD: Stop and take a moment to understand the effect of the counterweight. HAZARD: The counterweight forces the vertical column to travel toward the top of the Studio Stand. Without a load [Camera, laptop, etc.] on the horizontal Arm/Bar, it travels toward the top of the stand. HAZARD: Use the stand with a load [Camera, laptop, etc.]. Always securely “Park” the Vertical Carriage by Turning the Vertical Carriage Knob/ brake fully Clock Wise before and after repositioning or before the stand is unloaded [removing the Camera, laptop, etc.].
- HAZARD: Work in such a way that you’re always standing behind or in front of the stand. Keep clear of the Horizontal Arm/Bar and accessories. Take extra notice of your body position when you are releasing the Vertical Carriage Knob/brake. With your free hand apply a downward force to the Horizontal Arm/Bar Simultaneously as you release the Vertical Carriage Knob/brake.
- Storage: When not in use, store with Vertical Carriage in the uppermost “Parking Position”. Review this manual with all Studio personnel prior to operating the Studio Stand.
- Re-tighten all fasteners AGAIN. Re-tighten fasteners after the first shoot. Tighten yearly.
A studio stand is used by professional and commercial photographers to capture images accurately with repeatability. It provides a rigid and stable platform essential for High-Resolution Sensors used in DSLR, Medium Format, and Large Format cameras and imaging systems. A studio stand reduces vibrations that are present when shooting handheld. Reduced vibration increases image sharpness. It enables the photographer to focus on the subject matter and image composition instead of hand-holding the camera. It provides creative shooting options using heights and angles that are unachievable when hand-holding a camera. It provides the foundation stone that enables the photographer to develop their own technical workflow. As the workflow evolves to include advanced imaging practices, the results can be seen as sharper images. With an adjustable camera head, the user can accurately set up the camera to maintain the camera-to-subject flatness of field in both the vertical and horizontal planes of travel. The flatness of the field is maintained as the user moves the stand both vertically and horizontally eliminating perspective distortion. Shooting tethered with an optional accessory/laptop shelf, reduces floor cabling and allows the photographer to immediately confirm both focus and lighting. A Studio Stand reduces user fatigue. The internal counterbalance offsets the weight of the camera and computer. Allowing the user to easily move the camera and computer up and down and left and right using only one hand. This promotes good body ergonomics which can prevent tennis elbow.
Tip Over Hazard:
Caution must be used when moving the stand to prevent tip-over. Move the stand slowly and avoid uneven surfaces as well as low and high-level objects. Additional caution must be used when the Horizontal arm with load (Camera or Laptop Shelf) is used in the upper area above the mid-point of the stand.
Counterweight Hazard:
The Horizontal Arm/Bar is connected to a counterweight located inside the Vertical Center/Column. Caution must be used at all times when using the Horizontal Arm/Bar. The Vertical Carriage Knob/Brake must always be tightened to lock the Horizontal Arm/Bar in place. Without a load on the Horizontal Arm/Bar it can travel upwards. When releasing the Vertical Carriage Knob/Brake stand clear of the arms path of movement, firmly hold the Horizontal Arm/Bar applying pressure downwards. Stand back to avoid contact with the Horizontal Arm/Bar when unloaded. Do not remove the load when the Vertical Carriage Knob/Brake knob is released or turned CCW. Unless repositioning the Vertical Center/Column intentionally the Vertical Carriage Knob/Brake must be fully engaged (turned fully clockwise). Store with Vertical Carriage in the uppermost “Parking Position.”
Options and accessories are available for sale either through your preferred authorized retailer or studiotitanamerica.com.
Options:
- STA 01-350LW-10 [3 x 10KG/22lb /ea BOLT UNDER – steel leg weights for 01-350MK2 series]
- STA 01-350LW-15 [3 x 15KG/33lb /ea BOLT UNDER – steel leg weights for 01-350MK2 series]
- STA 06-105 Folding Arm [The two-jointed folding arm attaches to the vertical carriage bracket via a quick-release pin. It provides articulated movement of an independent Camera plate in free space. It provides load balancing via an adjustable internal pneumatic cylinder. The camera plate remains parallel with the ground as the arm position changes vertically. Designed and developed together with the MET for digital imaging of Museum statues and artifacts. Requires STA 01-350LW-15 3 x 15KG/33lb /ea BOLT UNDER – steel leg weights for 01-350MK2 series]
STA 01-350R-MK2 Specification & Directions for Materials Recycling
- Total Height: 240cm / 94.4 in **
- Working Height Maximum: 220cm / 86.6 in (measured from Camera Plate to floor)
- Working Height Minimum: 50cm / 19.7 in (measured from Camera Plate to floor)
- Rotational Range of Horizontal Bar: 0-360 degrees
- Working Width Horizontal – Fully Extended to
- Left: 83.5cm / 32.8 in (center of Column to center of Camera plate)
- Working Width Horizontal – Fully Extended to
- Right: 83.5cm / 32.8 in (center of Column to the center of Cam-era plate)
- Overall Working Width Horizontal – Fully Extended from
- Left to Fully Extended Right: 167cm / 65.6 in (center of Camera plate to the center of Camera plate)
- Width: 100cm / 39.3 in
- Weight: 53kg / 116lbs
- Suggested Wheels: 01-350-20-024
- Base Diameter: 100cm / 39.3 in
- Recommended General load capacity: 10kg (22lbs)
- Camera Plate Hardware: 3/8th inch – 16 thread
- Caster Wheel Diameter: 76mm / 3 in
- Includes two Camera Head Mount Plates and Basket as shown.
- The total Height for custom orders will be as specified in the quotation. Options:
- Large accessory shelf STA-01-395 for notebook computer
- Small accessory shelf STA-01-397A for notebook computer
- Leg Weight set STA 01-350LW 3 × 10Kg / 22lb/ea. bolt on internal steel leg weights
- STA-01-390 3-wave head
STUDIO TITAN KOREA RESERVES THE RIGHT TO MAKE PRODUCT CHANGES AND PRODUCT EN- HANCEMENTS. PRODUCTS SUPPLIED MAY NOT BE DELIVERED EXACTLY AS ADVERTISED OR SHOWN ON THE WEBSITE OR IN THE MANUAL.
- The column box’s blue outer plastic material is Polypropylene, abbreviated as PP, is a recyclable thermo-plastic polymer widely used in many different products. PP is rugged. PP’s resin identification code is 5, and it is recyclable.
- Plastic bags are made of LDPE (Low-Density Polyethylene) – Recyclable plastic (check Local Authority) LDPE can be recycled. However, check with your Local Authority to ensure it is re-cycled in your area. This is described as a hard flexible plastic.
- The Corrugated cardboard box can be recycled at de-pots, in municipal curbside collection programs, and through private recyclers.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>