Studio Titan STA 01-350R-MK2-10 Rotating Commercial Studio Camera Stand Instruction Manual

August 29, 2024
Studio Titan

Studio Titan STA 01-350R-MK2-10 Rotating Commercial Studio Camera Stand

Studio-Titan-STA-01-350R-MK2-10-Rotating-Commercial-Studio-Camera-Stand-
PRODUCT

Product Information

Specifications

  • Model: STA-01-350R-MK2
  • Component Types: Rotation, High Load – Rotation
  • Adjustability: Hand Lever adjustable, 360-degree range of movement

Product Usage Instructions

  • Identify the components based on the model type (Rotation or High Load – Rotation).
  • Follow the assembly steps provided in the manual for proper setup.
  • Avoid cross-threading components during assembly to prevent damage.
  • Cross-threading is not covered under warranty and may require replacement or repair.
  • Attach the Leg Assemblies to the base using the supplied fasteners and Hex Key tool.
  • Install the vibration reduction brackets on the legs using the provided hardware.
  • Remove the counterweight transportation securing screw and identify the counterweight cable.
  • Raise the Vertical/Center Column with assistance, ensuring proper handling.
  • Secure the Vertical Carriage/Brake Knob and Rotational Knob/Brake as per the diagrams provided.

FAQ

  • Q: What should I do if I encounter cross-threading during assembly?
  • A: Cross-threading is not covered under warranty. If you encounter cross-threading, stop assembly immediately and seek assistance for repair or replacement of damaged components.
  • Q: How should I handle the counterweight cable to avoid damage?
  • A: Always avoid contact with the counterweight cable. If the cable becomes frayed, stop use immediately and replace the cable to prevent injuries from sharp strands.

CAUTION
INSPECT BOXES AND INTERNAL COMPONENTS FOR SHIPPING DAMAGE PRIOR TO ASSEMBLY

WARNING
READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND OPERATION

CAUTION: Use supplied leather work gloves and safety glasses when handling the box, when opening the box, and when assembling the product.
HAZARD: Strapping is under tension and can jump when cut. Strapping and Buckles, Protective Edging, Plastic Walls, Plastic Caps, and Product Components and parts should be handled with care. Work slowly, and use extra caution to avoid any sharp edges.
Additional Tools may be Required: The essential tools are included. The following tools are recommended to be on site: Box Cutter, Scissors, Screw Driver, Plyers or Adjustable wrench, Metric Hex / Allen Key set

WARNING
TO AVOID THE DANGER OF SUFFOCATION, KEEP PLASTIC BAGS SUPPLIED WITH THIS PRODUCT AWAY FROM BABIES AND CHILDREN!

Studio-Titan-STA-01-350R-MK2-10-Rotating-Commercial-Studio-Camera-Stand-
FIG-1

Transit Damage

Each package is inspected before being shipped from the warehouse to ensure that is in perfect condition. The column shipping boxes are constructed using extra-thick cardboard. Some packaging includes engineered plastic walls, end caps, and banding. The columns are packed using engineered plastic walls and in dense foam to protect and absorb energy from reasonable drops and impacts. The column packaging is designed and drop-tested from approximately 5 feet [1.5 Meters] without sustaining any internal damage. The packaging is crush tested using a 660lb [300kg] weight placed along the long side of the box without sustaining any internal damage. If handled without care the boxes will show signs of transit damage. Wearing supplied work Gloves, while following the Assembly Steps, carefully inspect the contents inside the boxes. Specifically, the Vertical center column top cap pulley should be securely fastened to the top of the Vertical center column as shown on the [component identification] page. In the base, the transportation counterweight securing strap should be secured to the counterweight. [See Diagram: E] If anything seems unusual, !!!STOP!!! Send images to: info@studiotitanamerica.com for a second opinion. If there are damaged OR Loose parts, do not assemble the stand, you may injure yourself. If the damage is noticeable such as cracks or loose or broken parts contact your dealer for exchange. If the damage is minor or cosmetic and does not compromise the safe assembly or operation of the stand send images of the parts that are affected to: info@studiotitanamerica.com. Arrangements will be made to provide you with replacement parts to restore the stand to new condition.

CAUTION
INSPECT BOXES AND INTERNAL COMPONENTS FOR SHIPPING DAMAGE PRIOR TO ASSEMBLY

Product Identification

Product Nameplate / Label is located on the vertical column assembly.
The label information is indicated below:
STUDIO TITAN AMERICA

  • No.[Model Number] – [Manufacture Date]
  • Imported by / Importe par
  • STEPHANIE MCNEIL CORPORATION
  • 250 Augusta Ave, Suite 204
  • Toronto, ON M5T 2L7 CANADA
  • Manufactured in / Fabrique en
  • SOUTH KOREA

Label examples are indicated below

Studio-Titan-STA-01-350R-MK2-10-Rotating-Commercial-Studio-Camera-Stand-
FIG-2

Intended use

This product is intended for use by professional and commercial photographers in a studio environment with a high ceiling. The wheels are designed to be used indoors on a floor that is smooth, hard, flat, and unobstructed. The Studio Stands with internal counterweights are designed to be used at all times with a load (Camera or laptop shelf or both).

CAUTION: This product is not recommended for use by hobbyists or in a household environment with a low ceiling or carpeted floors. Carpeting or pitted surfaces are not recommended because of the increased rolling resistance which can cause the stand to tip over.

If the surface is not ideal, the stand must be moved with CAUTION, very slowly, using both hands one at the top and the other at the bottom to steady the stand to prevent the stand from tipping over. If the surface is not ideal, lower the load to the waist level before moving the stand. We also recommend the use of a sandbag or weight attached at the base when conditions are not ideal to prevent tipping over. Ultimately it’s the users’ responsibility to understand how the stand operates and to use the stand within its specification limits, as intended to ensure their safety and the safety of their equipment. It is also recommended to use a short tether cable to secure the camera to the stand if the head, head plate, attachment stud or camera adapter plate comes loose or fails. Some assembly is required, we recommend using an assistant during the initial product assembly. Please read all documentation prior to assembly.

CAUTION
TIPPING HAZARD
WARNING
READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND OPERATION

Component Identification

Component Identification: STA-01-350R-MK2 -10 (Rotation)

Studio-Titan-STA-01-350R-MK2-10-Rotating-Commercial-Studio-Camera-Stand-
FIG-3Studio-Titan-
STA-01-350R-MK2-10-Rotating-Commercial-Studio-Camera-Stand-
FIG-4

CAUTION! Cross Threading Components

Cross-threading components during assembly is not covered under the warranty

  • Cross-threading is a term that describes damage that is caused when a misaligned screw or knob thread is forced into a threaded hole. When this occurs, threads are damaged and are no longer capable of proper operation.
  • The remedy is replacement or repair of the damaged component/s.
  • AVOID cross-threading of mounting screws and knobs during assembly using this easy-to-follow procedure:
  • While standing in front of and looking into the threaded hole. Place the screw or knob thread against the threaded hole. Using one hand, hold the thread between your fingers. With the other hand hold the hex key like a pencil or place your index finger in the center of the knob. Align the screw or knob with the hole as indicated in the picture with the checkmark below.
  • Slowly turn it counter-clockwise or left, several turns, until you hear a click or feel the start of the thread. Then proceed slowly, turning clockwise or right, gently using only finger force to tighten the screw or knob. If you feel increased resistance, the threads are not aligned, remove them and start procedure from the beginning again.

Studio-Titan-STA-01-350R-MK2-10-Rotating-Commercial-Studio-Camera-Stand-
FIG-5

Component Identification: STA-01-350R-MK2- TRI (High Load – Rotation)

Securing / Transport Screw

Studio-Titan-STA-01-350R-MK2-10-Rotating-Commercial-Studio-Camera-Stand-
FIG-6

HD Interface Plate

Studio-Titan-STA-01-350R-MK2-10-Rotating-Commercial-Studio-Camera-Stand-
FIG-7

WARNING
READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND OPERATION

Hand Lever adjustable, 360-degree range of movement, camera head mount plates

Studio-Titan-STA-01-350R-MK2-10-Rotating-Commercial-Studio-Camera-Stand-
FIG-8

WARNING
READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND OPERATION

Assembly Steps

  • Wearing gloves and together with your Assistant……..

  • Place the Column Box [long rectangular box] flat on the floor. Place some packing materials on the floor. Do not stand the Vertical/Center Column vertically. Remove and Lay the Vertical/ Center Column flat on the floor. Under the Base, Visually inspect and

  • Confirm that the Counterweight transport securing SCREW is present which secures the counterweight during transportation.

  • Do NOT remove the Counterweight transport securing SCREW until advised later.

  • Confirm the bolt is present and proceed to step 2 with assembly. If NOT, then:

  • If Counterweight transport securing SCREW is NOT present, the counterweight is loose and can move inside the column. Do not stand the column vertically. Stop the SET-UP and Contact STEPHANIE MCNEIL CORPORATION for further instructions.

  • Please email info@studiotitanamerica.com with the best phone number to reach you. We normally respond within 24hrs, during weekdays.

  • Attach the three Leg Assemblies to the base.
    [See Diagram: A] Three fasteners are supplied and attached to each Leg Assembly. Use the supplied Hex Key tool to tighten the nine fasteners by hand. Attach the vibration reduction brackets to the legs using the Hex key tool and four fasteners lock washers & washers.
    Note: two of the leg assemblies are supplied with foot plungers. To have direct access to the foot plungers, install the foot plungers facing the operator or on the same side of the stand that the Horizontal and Vertical scales face.

  • Wearing Gloves, remove the counterweight transportation securing SCREW [See Component Identification STA 01-350MK2 Diagram ]

  • Locate and identify the counterweight cable.
    [See Component Identification STA 01-350MK2 Diagram ]

  • CAUTION!  AVOID CONTACT WITH THE COUNTERWEIGHT CABLE AT ALL TIMES. CAUTION MUST USED TO AVOID PINCHING YOUR FINGER DURING SET-UP AND NORMAL OPERATION.

  • The counterweight cable may become frayed during transportation or normal use. When frayed, stop using the stand and immediately replace the cable. Cable strands that separate may become sharp.

Studio-Titan-STA-01-350R-MK2-10-Rotating-Commercial-Studio-Camera-Stand-
FIG-9

  • Together with your Assistant…Wearing Gloves …..Carefully, Slowly raise and lift the Vertical/ Center Column until it is standing freely on its wheels.
  • Locate the M8 Hex Wrench. Refer to the section “Cross Threading Components.” Remove the six M8 x 20 screws from the Vertical carriage. Two M8 screws from the front and two from each side. [Diagrams: B1&B2 indicate the screw locations] Locate the
  • Horizontal Arm/Bar Carriage Assembly. [See Component Identification STA 01-350R Diagram] Together with your assistant. Have your assistant hold the Horizontal Arm/Bar Carriage Assembly in place while you fasten it with the six M8 x 20 screws. Note the order. [screw, spring washer, and then flat washer] Hand tightening with the Hex Wrench is recommended. If you have a torque wrench tighten the M8 screws to 45Nm or 33 lb/ft. not more.
  • Locate the M6 Hex Wrench. Refer to the section “Cross Threading Components.” Locate the loose Vertical / Brake Knob. Find the Location of the Vertical Carriage / Brake Knob Transportation Set Screw. [See DIAGRAM: D]. With the M6 Hex Wrench FIRST
  • Remove the transportation set screw and THEN replace it with a Vertical Carriage / Brake Knob. Turn the Vertical Carriage /Brake Knob fully Clock Wise to secure the vertical carriage in the uppermost or “parking position.” Locate the loose Rotational Knob /
  • Brake. Refer to the section “Cross Threading Components.” Insert and fasten the Rotational Knob / Brake into the Rotational carriage. [See DIAGRAM: E]

Studio-Titan-STA-01-350R-MK2-10-Rotating-Commercial-Studio-Camera-Stand-
FIG-10

Component Identification: STA-01-350R-MK2- TRI (High Load – Rotation)

Studio-Titan-STA-01-350R-MK2-10-Rotating-Commercial-Studio-Camera-Stand-
FIG-11

Studio-Titan-STA-01-350R-MK2-10-Rotating-Commercial-Studio-Camera-Stand-
FIG-12

  • Locate two M8 Hex wrenches. Locate the Basket.
    Locate the Basket Shaft. [See Component Identification STA 01-350R Diagram] Refer to the section “Cross Threading Components.” With the first M8 hex key hold the M8 screw at the top of the Basket shaft. With the second M8 hex key loosen the M8 screw at the bottom of the Basket shaft. Attach the Basket to the Basket Shaft.
    Note the order of fastener connection: [Screw , Flat washer, Basket Plate, Flat Washer]. [See: DIAGRAM: C]

  • CAUTION: [Only with the Horizontal Arm/Bar in the uppermost position “parking position”.] Slowly release the Vertical Carriage Knob/brake by turning it Counter Clock Wise. This will release the vertical carriage allowing it to travel freely up and down the Vertical Center / Colum. Confirm that the Vertical Carriage is free to move in both directions while using both hands to hold the Horizontal Arm/Bar. Turn the Vertical Carriage Knob/brake fully Clock Wise to secure the vertical carriage.

  • Locate the Two Horizontal Carriage Knob/ Brakes. [See Component Identification STA 01- 350R Diagram] Turn the Horizontal Carriage Knob/Brake Counter Clockwise to release and confirm that the Horizontal Arm / Bar is free to move left and right.
    STOP SET-UP— Read below— GO TO STEP 11 If anything seems unusual or if the vertical carriage is not moving freely up or down. Stop Set-up and send a few images of the stand to: info@studiotitanamerica.com for assistance.

Studio-Titan-STA-01-350R-MK2-10-Rotating-Commercial-Studio-Camera-Stand-
FIG-13

Use & Maintenance Steps

  • HAZARD: Stop and take a moment to understand the effect of the counterweight. HAZARD: The counterweight forces the vertical column to travel toward the top of the Studio Stand. Without a load [Camera, laptop, etc.] on the horizontal Arm/Bar, it travels towards the top of the stand.
  • HAZARD: Use the stand with a load [Camera, laptop, etc.]. Always securely “Park” the Vertical Carriage by Turning the Vertical Carriage Knob/ brake fully Clock Wise before and after repositioning or before the stand is unloaded [removing the Camera, laptop, etc.].
  • HAZARD: Work in such a way that you’re always standing behind or in front of the stand. Keep clear of the Horizontal Arm/Bar and accessories. Take extra notice of your body position when you are releasing the Vertical Carriage Knob/brake. With your free hand apply a downward force to the Horizontal Arm/Bar Simultaneously as you release the Vertical Carriage Knob/brake.
  • Storage: When not in use, store with Vertical Carriage in the uppermost “Parking Position”. Review this manual with all Studio personnel before operating the Studio Stand.
  • Re-tighten all fasteners AGAIN. Re-tighten fasteners after the first shoot. Tighten yearly.

Assembly Steps: STA-01-350LW-15 Leg Weight Set

  1. Locate the hex key and remove the hex screw from the leg weight. Note the order of fastener connection: [Screw and then, Lock washer and then Flat washer.], [See: DIAGRAM: A]
  2. Locate the hole in the leg of the base. Position the leg weight under the leg. Lift the leg weight and position it under the leg hole so you can see the integrated nut in the leg weight. With the hex key tighten the fastener. Repeat for the two remaining legs.

STA-01-350LW-15 Leg Weight Set Specification

  • Individual Leg Weight: 3 x 15kg / 33lbs
  • Total Weight: 45 kg / 99 lbs

Material composition
The weight and bolt is made of steel. This product does not contain lead.

Studio-Titan-STA-01-350R-MK2-10-Rotating-Commercial-Studio-Camera-Stand-
FIG-14

Theory of Operation

  • A studio stand is used by professional and commercial photographers to capture images accurately with repeatability. It provides a rigid and stable platform essential for High Resolution Sensors used in DSLR, Medium Format, and Large Format cameras and imaging systems. A studio stand reduces vibrations that are present when shooting handheld.
  • Reduced vibration increases image sharpness. It enables the photographer to focus on subject matter and image composition instead of hand-holding the camera. It provides creative shooting options using heights and angles that are unachievable when hand-holding a camera. It provides the foundation stone that enables the photographer to develop their technical workflow. As the workflow evolves to include advanced imaging practices, the results can be seen as sharper images.
  • With an adjustable camera head, the user can accurately set up the camera to maintain camera-to-subject flatness of field in both the vertical and horizontal planes of travel. The flatness of the field is maintained as the user moves the stand both vertically and horizontally eliminating perspective distortion.
  • Shooting tethered with an optional accessory/laptop shelf, reduces floor cabling and allows the photographer to immediately confirm both focus and lighting. A Studio Stand reduces user fatigue. The internal counterbalance offsets the weight of the camera and computer. Allowing the user to easily move the camera and computer up and down and left and right using only one hand. This promotes good body ergonomics which can prevent tennis elbow.

Tip Over Hazard

Caution must be used when moving the stand to prevent tip-over. Move the stand slowly and avoid uneven surfaces as well as low and high-level objects.
Additional caution must be used when the Horizontal arm with load (Camera or Laptop Shelf) is used in the upper area above the midpoint of the stand.

Counterweight Hazard

  • The Horizontal Arm/Bar is connected to a counterweight located inside the Vertical Center/ Column. Caution must be used at all times when using the Horizontal Arm/Bar. The Vertical Carriage Knob/Brake must always be tightened to lock the Horizontal
  • Arm/Bar in place. Without a load on the Horizontal Arm/Bar, it can travel upwards.
  • When releasing the Vertical Carriage Knob/Brake stand clear of the arms path of movement, firmly hold the Horizontal Arm/Bar applying pressure downwards. Stand back to avoid contact with the Horizontal Arm/Bar when unloaded. Do not remove the load when the Vertical Carriage Knob/Brake knob is released or turned CCW. Unless repositioning the Vertical Center/ Column intentionally the Vertical Carriage Knob/ Brake must be fully engaged (turned fully clockwise).
  • Store with Vertical Carriage in the upper most “Parking Position.”

STA-01-350R-MK2-10 (Rotation) Options and Accessories

  • Options and accessories can be purchased through your preferred authorized retailer or the studiotitanamerica.com website.

Options

  • STA 01-390 3-way head
  • STA 01-395 Large Accessory Shelf for notebook computer
  • STA 01-397 Small Accessory Shelf for notebook computer

STA 06-105 Folding Arm [The two-jointed folding arm attaches to the vertical carriage bracket via a quick-release pin. It provides articulated movement of an independent Camera plate in free space. It provides load balancing via an adjustable internal pneumatic cylinder.
The camera plate remains parallel with the ground as the arm position changes vertically. Designed and developed together with the MET for digital imaging of Museum statues and artifacts. Requires STA 01-350LW-15 3 x 15KG/33lb /ea BOLT UNDER – steel leg weights for 01-350MK2 series]Studio-Titan-STA-01
-350R-MK2-10-Rotating-Commercial-Studio-Camera-Stand-
FIG-15

STA-01-350R-MK2-10 (Rotation) Specification & Directions for Materials Recycling

  • Total Height: 3246mm / 10.65 ft / 127.9 in
  • Working Height Maximum: 3048mm / 10ft /120 in measured from Camera Plate to floor)
  • Working Height Minimum: 500mm / 19.7 in (measured from Camera Plate to floor)
  • Rotational Range of Horizontal Bar: 0-360 degrees
  • Overall Width Horizontal Bar: 1000mm / 39.3 in (measured end to end)
  • Working Width Horizontal Bar- Fully Extended to one side of the vertical column: 835mm / 32.8 in (center of Camera plate to the center of Vertical column)
  • Width: 1000mm / 39.3 in
  • Weight of Stand including STA-01-350LW-15: 110kg / 244lbs
  • Suggested Wheels: 01-350-20-024
  • Base Diameter: 1000mm / 39.3 in
  • Recommended General load capacity: 10kg (22lbs)
  • Camera Plate Hardware: 3/8th inch – 16 thread
  • Includes: two Camera Head Mount Plates and a Basket as shown
  • Includes: Leg Weight Set STA-01-350LW-15
  • Caster wheel diameter: 76mm / 3 in

Options

  • Large accessory shelf STA-01-395 for notebook computer
  • Small accessory shelf STA-01-397A for notebook computer
  • STA-01-390 3-way head

Material composition: The Vertical and Horizontal columns are made of aluminum. The counter counterweight is S20C steel. The nuts and bolts are made of steel. The casters are polyurethane. This product does not contain lead.
STUDIO TITAN KOREA RESERVES THE RIGHT TO MAKE PRODUCT CHANGES AND PRODUCT ENHANCEMENTS. PRODUCTS SUPPLIED MAY NOT BE DELIVERED EXACTLY AS ADVERTISED OR SHOWN ON THE WEBSITE OR IN THE MANUAL.

  • The column box’s blue outer plastic material is Polypropylene, abbreviated as PP, is a recyclable thermoplastic polymer widely used in many different products. PP is rugged. PP’s resin identification code is 5, and it is recyclable.
  • Plastic bags are made of LDPE (Low-Density Polyethylene) – Recyclable plastic (check Local Authority) LDPE can be recycled. However, check with your Local Authority to ensure it is recycled in your area. This is described as a hard flexible plastic.
  • The Corrugated cardboard box can be recycled at depots, in municipal curbside collection programs, and through private recyclers.

CONTACT

Imported by

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals