Studio Titan STA 01-360MK2 Professional Studio Camera Stand User Manual
- June 5, 2024
- Studio Titan
Table of Contents
STA 01-360MK2 Professional Studio Camera Stand
User Manual
CAUTION: Use leather work gloves and safety glasses when handling the
box, when opening the box, and when assembling the product.
HAZARD: Strapping is under tension and can jump when cut. Strapping and
Buckles, Protective Edging, Plastic Walls, Plastic Caps, and Product
Components and parts should be handled with care. Work slowly, use extra
caution to avoid any sharp edges.
Additional Tools may be Required: The essential tools are included. The
following tools are recommended to be on site: Box Cutter, Scissors, Screw
Driver, Plyers or Adjustable
Transit Damage:
Each package is inspected prior to being shipped from the warehouse to insure
that is in perfect condition. The column shipping boxes are constructed using
extra-thick cardboard. Some packaging includes engineered plastic walls, end
caps, and banding. The columns are packed using engineered plastic walls and
in dense foam to protect and absorb energy from reasonable drops and impacts.
The column packaging is designed and drop tested from approximately 5 feet
[1.5 Meters] without sustaining any internal damage. The packaging is crush
tested using a 660lb [300kg] weight placed along the long side of the box
without sustaining any internal damage. If handled without care the boxes will
show signs of transit damage. Wearing work Gloves, while following the
Assembly Steps, carefully inspect the contents inside the boxes. Specifically,
the Vertical center column top cap pulley should be securely fastened to the
top of the Vertical center column as shown on the [component identification]
page. In the base, the transportation counterweight securing strap should be
secured to the counterweight. [See Diagram: E] If anything seems unusual,
!!!STOP!!! Send images to:
info@studiotitanamerica.com for a second
opinion. If there are damaged OR Loose parts, do not assemble the stand, you
may injure yourself. If the damage is noticeable such as cracks or loose or
broken parts contact your dealer for exchange. If the damage is minor or
cosmetic and does not compromise the safe assembly or operation of the stand
send images of the parts that are affected to:
info@studiotitanamerica.com. We will
make arrangements to provide you with replacement parts to restore the stand
to new condition.
CAUTION
INSPECT BOXES AND INTERNAL COMPONENTS FOR SHIPPING DAMAGE PRIOR TO
ASSEMBLY
CAUTION
INSPECT BOXES AND INTERNAL COMPONENTS FOR SHIPPING DAMAGE PRIOR TO ASSEMBLY
Product Identification:
Product Nameplate / Label is located on the vertical column assembly.
The label information is indicated below:
STUDIO TITAN AMERICA
No.[Model Number] – [Manufacture Date] Imported by / Importe par STEPHANIE
MCNEIL CORPORATION 250 Augusta Ave, Suite 204 Toronto, ON MST 2L7 CANADA
Manufactured in / Fabrique en SOUTH KOREA
Label examples are indicated below:
Intended use:
This product is intended for use by professional and commercial photographers
in a studio environment with a high ceiling. The wheels are designed to be
used indoors on a floor that is smooth, hard, flat and unobstructed. The
Studio Stands with internal counterweight are designed to be used at all times
with a load (Camera or laptop shelf or both).
CAUTION: This product is not recommended for use by hobbyists or in a
household environment with a low ceiling or carpeted floors. Carpeting or
pitted surfaces are not recommended because of the increased rolling
resistance which can cause the stand to tip over. If the surface is not ideal,
the stand must be moved with CAUTION, very slowly, using both hands one at the
top and the other at the bottom to steady the stand in order to prevent the
stand from tipping over. If the surface is not ideal, lower the load to waist
level before moving the stand. We also recommend the use of a sandbag or
weight attached at the base when conditions are not ideal to prevent tipping
over. Ultimately it’s the users responsibility to understand how they stand
operates and to use the stand within its specification limits, as intended to
insure their own safety and the safety of their equipment. It is also
recommended to use a short tether cable to secure the camera to the stand in
the event that the head, head plate, attachment stud or camera adapter plate
comes loose or fails. Some assembly is required, we recommend using an
assistant during the initial product assembly. Please read all documentation
prior to assembly.
Component Identification: STA 01-360MK2
Component Identification: STA 01-360MK2 CAUTION! Cross Threading
Components:
Cross-threading components during assembly are not covered under
warranty.
Cross-threading is a term that describes the damage that is caused when a
misaligned screw or knob thread is forced into a threaded hole. When this
occurs, threads are damaged and are no longer capable of proper operation. The
remedy is replacement or repair of the damaged component/s.
AVOID cross-threading of mounting screws and knobs during assembly using
this easy to follow the procedure:
While standing in front of and looking into the threaded hole. Place the
screw or knob thread against the threaded hole. Using one hand, hold the
thread between your fingers. With the other hand hold the hex key like a
pencil or place your index finger in the center of the knob. Align the screw
or knob with the hole as indicated in the picture with the checkmark below.
Slowly turn it counter-clockwise or left, several turns, until you hear a
click or feel the start of the thread. Then proceed slowly, turning clockwise
or right, gently using only finger force to tighten the screw or knob. If you
feel increased resistance, the threads are not aligned, remove and start the
procedure from the beginning again.
Assembly Steps:
-
Wearing Gloves and together with your Assistant…Wearing Gloves …..Place the Column Box [long rectangular box] flat on the floor. Place some packing materials on th floor. Do not remove and stand the Vertical/Center Column vertically. Remove the Vertical/Center Column and Lay the Vertical/Center Column flat on the floor. Under the Base, Visually inspect and Confirm that the Counterweight strap is present securing the counterweight to the counterweight stop pin. [See Diagram: D] Do NOT remove the Counterweight strap until advised later. If the strap is present proceed to step 2 with assembly. If NOT, then follow the instructions below:
If the Counterweight strap is NOT present: the counterweight is loose and can move inside the column. Do not stand the column vertically. Stop the SET-UP and Contact us through the Studio Titan America website for further instructions.
Please email: info@studiotitanamerica.com with the best phone number to reach you. We normally respond within 24hrs, during weekdays.
WARNING
READ ALL INSTRUCTIONS PRIOR TO ASSEMBLY AND OPERATION -
Attach the three Leg Assemblies to the base. [See Diagram: A] The Hex Key tool is supplied and fasteners are supplied attached to the Base. Use the supplied Hex Key Loosen the fasteners, insert the legs, and then re-tighten by hand. Note: two of the leg assemblies are supplied with foot plungers. To have direct access to the foot plungers you will want to install the foot plungers facing the operator or on the same side of the stand that the Horizontal and Vertical scales face. [If the floor is polished or on an angle consider ordering a third leg assembly with a plunger. This is a special order, please email info@studiotitanamerica.com for additional information].
-
Wearing Gloves, using a screwdriver, remove the counterweight transportation securing band. [See Diagram: D] !!!CAUTION!!! DO NOT INSERT OR PUT FINGERS INSIDE THE BOTTOM OF THE VERTICAL COLUMN OR BEYOND THE COUNTERWEIGHT PIN. THE COUNTERWEIGHT IS HEAVY AND CAN INJURE YOUR FINGER. [See Diagram: E]
-
Locate and identify the counterweight cable from the component identification page. !!! CAUTION!!! AVOID CONTACT WITH THE COUNTERWEIGHT CABLE AT ALL TIMES. CAUTION MUST BE USED TO AVOID FINGER OR HAND INJURY DURING SET-UP AND NORMAL OPERATION. The counterweight cable may become frayed during transportation or normal use. When frayed, stop using the stand and immediately replace the cable. Cable strands that separate may become sharp.
WARNING
READ ALL INSTRUCTIONS PRIOR TO ASSEMBLY AND OPERATION
-
Together with your Assistant…Wearing Gloves Carefully, Slowly raise and lift until the Vertical/ Center Column until it is standing freely on its wheels.
-
Locate the M8 Hex Wrench. Refer to section “Cross Threading Components.” Remove the four M8 x 20 bolts from the Vertical carriage. [See DI-AGRAM: B] Locate the Horizontal Arm/Bar Carriage Assembly See [component identification] page. Together with your assistant. Have your assistant hold the Horizontal Arm/Bar Carriage Assembly in place while you fasten it with the four M8 x 20 bolts. Note the order [See DIAGRAM: B] [Bolt, Spring washer, and then Flat washer]. Hand tightening with the Hex Wrench is recommended. If you have a torque wrench tighten the M8 bolts to 45Nm or 33 lb/ft not more.
-
Locate the M6 Hex Wrench. Locate the loose Vertical / Brake Knob. Locate the location of the Vertical Carriage / Brake Knob See [Transportation Set Screw] [See DIAGRAM: D & B]. Refer to section “Cross Threading Components.” With the M6 Hex Wrench Remove the transportation set screw and replace it with a Vertical Carriage / Brake Knob. Turn the Vertical Carriage /Brake Knob fully Clock Wise to secure the vertical carriage in the uppermost or “parking position” [See DIAGRAM: D]
-
Locate two M8 Hex wrenches. Locate the Basket. Locate the Basket Shaft, See [component identification] page. With the first M8 hex key hold the M8 bolt at the top of the Basket shaft. With the second M8 hex key loosen the M8 bolt at the bottom of the Basket shaft. Attach the Basket to the Basket Shaft. Note the order of fastener connection: [Bolt, Flat washer, Basket Plate, Flat Washer]. [See: Component Identification page and DIAGRAM: C]
-
CAUTION: [Only with the Horizontal Arm/Bar in the uppermost position “parking position”.] Slowly release the Vertical Carriage Knob/brake by turning it Counter Clock Wise. This will release the vertical carriage allowing it to travel freely up and down the Vertical Center / Colum. Confirm that the Vertical Carriage is free to move in both directions while using both hands to hold the Horizontal Arm/Bar. Turn the Vertical Carriage Knob/brake fully Clock Wise to secure the vertical carriage.
-
Locate the Two Horizontal Carriage Knob/ Brakes, See [component identification] page. Turn the Horizontal Carriage Knob/Brake Counter Clockwise to release and confirm that the Horizontal Arm / Bar is free to move left and right.STOP SET-UP– Read below– GO TO STEP 11 If anything seems unusual or if the vertical carriage is not moving freely up or down. Stop Set-up and send a few images of the stand to: info@studiotitanamerica.com for assistance. Use & Maintenance Steps:
-
HAZARD: Stop and take a moment to understand the effect of the counterweight.
HAZARD: The counterweight forces the vertical column to travel toward the top of the Studio Stand. Without a load [Camera, laptop, etc] on the horizontal Arm/Bar, it can travel quickly towards the top of the stand.
HAZARD: Never use the stand without a load [Camera, laptop, etc]. Always securely “Park” the Vertical Carriage by Turning the Vertical Carriage Knob/brake fully Clock Wise before and after re-positioning or before the stand is unloaded [removing Camera, laptop, etc]. -
HAZARD: Work in such a way so you’re always standing behind or in front of the stand so that you always stand clear of the Horizontal Arm/Bar and accessories. Take extra notice of your body position when you are releasing the Vertical Carriage knob. With your free hand-apply, a downward force to the Horizontal Arm/Bar Simultaneously as you release the Vertical Carriage knob.
-
Storage: Store with Vertical Carriage either in the uppermost “Parking Position” with the load removed or store the Studio Stand with a weight or sandbag on the Horizontal Arm/Bar to counteract the effect of the counterweight, in the event that non-trained personal attempt to use the Studio Stand. Train all Studio personnel prior to operating the Studio Stand.
-
Re-tighten all fasteners AGAIN. Re-tighten fasteners after the first shoot. Tighten yearly.
WARNING
READ ALL INSTRUCTIONS PRIOR TO ASSEMBLY AND OPERATION
Theory of Operation
A studio stand is used by professional and commercial photographers to capture images accurately with repeatability. It provides a rigid and stable platform essential for High-Resolution Sensors used in DSLR, Medium Format, and Large Format cameras and imaging systems. A studio stand reduces vibrations that are present when shooting handheld. Reduced vibration increases image sharpness. It enables the photographer to focus on the subject matter and image composition instead of hand-holding the camera. It provides creative shooting options using heights and angles that are unachievable when hand-holding a camera. It provides the foundation stone that enables the photographer to develop their own technical workflow. As the workflow evolves to include advanced imaging practices, the results can be seen as sharper images. With an adjustable camera head, the user can accurately set up the camera to maintain the camera to subject flatness of field in both the vertical and horizontal planes of travel. The flatness of field is maintained as the user moves the stand both vertically and horizontally eliminating perspective distortion. Shooting tethered with the optional laptop shelf reduces floor cabling and allows the photographer to immediately confirm both focus and lighting. A Studio Stand reduces user fatigue. The internal counterbalance offsets the weight of the camera and computer. Allowing the user to easily move the camera and computer up and down and left and right using only one hand. This promotes good body ergonomics which can prevent tennis elbow.
Tip-Over Hazard:
Caution must be used when moving the stand to prevent tip over. Move the stand
slowly and avoid uneven surfaces as well as low and high-level objects.
Additional caution must be used when the Horizontal arm with load (Camera or
Laptop Shelf) is used in the upper area above the midpoint of the stand.
Counterweight Hazard:
The Horizontal Arm/Bar is connected to a counterweight located inside the
Vertical Center/ Column. Caution must be used at all times when using the
Horizontal Arm/Bar. The Vertical Carriage Knob/Brake must always be tightened
to lock the Horizontal Arm/Bar in place. Without a load on the Horizontal
Arm/Bar it can accelerate upwards quickly. When releasing the Vertical
Carriage Knob/Brake stand clear of the arms path of movement, firmly hold the
Horizontal Arm/Bar applying pressure downwards. Stand back to avoid contact
with the Horizontal Arm/Bar when unloaded. Do not remove the load when the
Vertical Carriage Knob/Brake knob is released or turned CCW. Unless
repositioning the Vertical Center/Column intentionally the Vertical Carriage
Knob/Brake must be fully engaged (turned fully clockwise). Store with Vertical
Carriage either in the upper most “Parking Position” with the load removed or
store the Studio Stand with a weight or sandbag on the Horizontal Arm/Bar.
WARNING
READ ALL INSTRUCTIONS PRIOR TO ASSEMBLY AND OPERATION
Assembly Diagrams:
Assembly Diagrams:
!!! CAUTION !!!
DO NOT PUT YOUR FINGERS INSIDE THE BOTTOM OF THE VERTICAL COLUMN WHEN MOVING
THE STAND, STANDING IT UP, LAYING IT DOWN, OR DURING NORMAL OPERATION.
CONSIDER HOLDING THE LEGS WHEN STANDING IT UP OR LAYING IT DOWN. THE INTERNAL
BALANCING WEIGHT OR COUNTERWEIGHT RESTS ON THE METAL PIN WITH THE BLACK RUBBER
BUMPER. THE COUNTERWEIGHT WHEN MOVING DOWNWARDS CAN PINCH YOUR FINGER IF IT IS
INSIDE THE BOTTOM OF THE VERTICAL COLUMN. TO PREVENT THE COUNTERWEIGHT FROM
MOVING DURING SET-UP. PLACE THE STAND LYING DOWN OR HORIZONTALLY ALONG THE
FLOOR WHEN REMOVING THE COUNTERWEIGHT TRANSPORTATION BAND. THE IMAGE BELOW
SHOWS THE BOTTOM VIEW OF THE STAND LOOKING INTO THE BOTTOM OF THE VERTICAL
COLUMN. THE ARROW POINTS AT THE TRANSPORTATION SECURING BAND WHICH IS
SURROUNDS THE METAL PIN AND RUBBER BUMPER.
STA 01-360MK2 Specification
- Total Height : 192cm / 75.59 in
- Working Height Maximum : 180cm / 70.86 in (measured from Camera Plate to the floor)
- Working Height Minimum: 50cm / 19.7 in (measured from Camera Plate to the floor)
- Working Width Horizontal – Fully Extended to Left: 55cm / 21.6 in (center of Column to the center of Camera plate)
- Working Width Horizontal – Fully Extended to Right: 55cm / 21.6 in (center of Column to the center of Camera plate)
- Overall Working Width Horizontal – Fully Extended from Left to Fully Extended Right: 110cm / 43.2 in (center of Camera plate to center of Camera plate)
- Width : 85cm / 33.46 in
- Weight : 30kg / 66lbs
- Suggested Wheels: 01-360-20-024
- Base Diameter : 90cm / 35.4 in
- Recommended General load capacity : 7kg (15.4lbs)
- Camera Plate Hardware : 3/8th inch – 16 thread
- Includes two Camera Head Mount Plates and Basket as shown
Options:
-Large accessory shelf STA-01-395 for notebook computer
-Small accessory shelf STA-01-397A for notebook computer
-STA-01-390 3-way head
Material composition: The Vertical and Horizontal columns are made of
aluminum. The counterweight is S20C steel. The nuts and bolts are made of
steel. The casters are polyurethane. This product does not contain lead.
STUDIO TITAN RESERVES THE RIGHT TO MAKE PRODUCT CHANGES AND PRODUCT
ENHANCEMENTS. PRODUCTS SUPPLIED MAY NOT BE DELIVERED EXACTLY AS ADVERTISED OR
SHOWN ON THE WEBSITE OR IN THE MANUAL.
- The column box blue outer plastic material is Polypropylene, abbreviated as PP, is a recyclable thermoplastic polymer widely used in many different products. PP is rugged. PP’s resin identification code is 5, and it is recyclable.
- Plastic bags are made of LDPE (Low-Density Polyethylene) Recyclable plastic (check Local Authority) LDPE can be recycled. However, check with your Local Authority to ensure it is recycled in your area. This is described as a hard flexible plastic.
- The Corrugated cardboard box can be recycled at depots, in municipal curbside collection programs, and through private recyclers.
Imported by: STEPHANIE MCNEIL CORPORATION
250 Augusta Avenue – Suite 204
Toronto, Ontario, MST 2L7
Canada 647-879-7837
info@studiotitanamerica.com
studiotitanamerica.com
Made in: South Korea
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>