FLYSKY FS-ST8B Digital Proportional Radio Control System Instruction Manual

Manual
Digital Proportional Radio
Control System Copyright ©2023 Flysky Technology Co., Ltd.

Introduction

This system consists of the FS-ST8B transmitter and FS-Br01 receiver, and is specially designed for the bait boat model.
This system needs to be used with the boat control board. Through the transmitter, users can remotely control the boat’s driving, baiting, and light switch. Through the GPS satellite positioning  system on the integrated control board, it can automatically navigate the model boat to multiple destinations and return back to the starting place, with the travel distance calculated. When the  receiving signal is weak, the model boat will automatically turn back.
In order to facilitate the operator to control the bait boat, this transmitter is equipped with a display screen, to allow users to control the status of the bait boat in real time, such as the remote  signal strength, number of satellites, transmitter battery level and boat, etc. In addition, it is also equipped with the audible alarm system. There will be an audible alarm when the battery power of the transmitter or boat is too low.

1.1 Transmitter Overview

1.1.1 Controls Description
The matchup between the transmitter control and the bait boat function is described as follows (Note that the function is related to a specific protocol).
Left Stick: Controls the container.

• Up: N/A
• Down: When the left LED and right LED flash for three times at the same time, the left and right containers open.
• Left:When the left LED flashes for three times, the left container opens.
• Right: When the right LED flashes for three times, the right container opens.

Right Stick: Controls the bait boat to turn left or right and move forward or backward.

• Up: Controls the bait boat to move forward.
• Down: Controls the bait boat to move backward.
• Left: Controls the bait boat to turn left.
• Right: Controls the bait boat to turn right.

SWA Switch (three-position): Turns on and off the LED of the bait boat, and adjusts its

• Up: Turns off the LED.
• Middle: Turns on the LED, with low brightness.
• Down: Turns on the LED light, with high brightness.

VRB Knob: Adjusts the motor speed.
Left Button

• Press the button to start the auto return (Auto home) function. The boat will return to the starting point automatically. To exit the return function, press the button again or toggle the right  stick (the travel exceeds 2/3 in any direction). The bait boat will travel at the speed as defined by the stick position after exit.

Right Button: Fixed speed

• When you press the button during the boat movement, the boat will move forward with the current throttle output speed. In this case, the stick can only control the boat to turn left or right  or move backward. Note that the stick needs to toggle more than 2/3 of the travel so that the boat can move backward;
• When you press the button during the boat movement, if the throttle is in neutral position, the boat will stop. If the boat moves forward at this time, it will advance forward with the current throttle output speed.

1.2 Receiver Overview
FS-Br01 Receiver

1.2.1 Receiver LED Status
The LED status indicates the power supply state of the receiver and its working state.
Three- flash- one-off（slow flash): The receiver is waiting for firmware’ update or forced firmware’ update.
Three-flash-one-off（Fast flash): The firmware of the receiver is upgrading.
Fast flash:The receiver is waiting for binding or in the bind mode.
Slow flash: The LED flashes slowly when the receiver is not received the signal, or losing signal.
Solid on: The receiver and the transmitter is conneted normally.
1.3 Antenna Related
This transmitter supports two antennas (internal antenna and external antenna).

Introduction Before Use

2.1 Transmitter Battery
You can AA batteries or 2S lithium batteries for this transmitter.
2.2 Turn ON/OFF The Transmitter
After the battery is installed, press and hold the power switch for seconds to turn on the transmitter.
Note: If the throttle stick is not at its neutral position when the transmitter is powered on. A pop-up menu will appear to remind you to put the throttle stick to neutral position and send a alarm sound.
2.3 LED
This LED is a multi-color indicator. It displays in a variety of colors such as red, green, blue, yellow, cyan, purple, white, and dazzling colors. You may set it to none. In addition, you may set it  to display the electricity level. The brightness of LED can also be adjusted.
The LED can be used to indicate the status of the transmitter or to give an alarm when the transmitter voltage is low, as shown in the following table:

Main Menu

Note:

1. There will be an audible alarm when the battery power of the transmitter, meanwhile, the battery icon will be slow flashing, and the buzzer will buzze to prompt.
2. When the system detectes the battery power of the boat is lower than 20%, a popo-up prompt for low voltage alarm will be sent, meanwhile, and the boat will automatically return back to  the starting place.

Function Menu

This transmitter function menu includes the following functions, which can be set by users as required, including Boat Psn, Fish spot setting, Auto Home, Bind setting, Basic setting and System settings.

4.1 Boat Psn(Boat position)
Use to display the position of the bait boat in real time, including the bathymetric data of the current location, the temperature, and the distance between the current position and the starting  point. Ensure the transmitter and the receiver are connected normally and the starting point is saved before enabling this function. This function is related to the specific protocol.

4.2 Fish Spot Setting
You can set [Start point] and [Fishing point] through this function. A total of 30 fishing points can be set. You can navigate from one fishing point to another. As a result, you can start from the  starting point and navigate to the fishing point automatically.
You can select [Manual] or [Auto]. When you select [Manual], the manual interface appears, displaying the current boat direction and distance between the boat and fishing point. The bait boat  will approach the target fishing point through manual operation.
When you select [Auto], the bait boat automatically arrives at the fishing point saved according to the direction defined by the GPS. This function is related to the specific protocol.

4.3 Auto Home
When this function is enabled, the bait boat will automatically start to return to the starting point after the baiting is finished at the fishing point. Note that the starting point must be saved  before enabling this function.
Note: The function is available only when the bait boat is enabled with the auto-cruise.

4.4 Binding Setting
It is used to complete the bind between the FS-ST8B transmitter and FS-Br01 receiver.
The transmitter supports two-way binding. The transmitter will display the information returned from the receiver after the two-way binding is completed. In addition, the bind settings  (between the transmitter and receiver) has been completed before delivery from the factory.

4.5 Basic Setting
Used to set basic functions, including Stick calibration, Firmware Update, About and More.

4.5.1 Stick Calibration
The calibration is required in case of data offset of the transmitter due to physical wear in long-term operations. At this time, we need to calibrate the output data and neutral angle of the stick,  and potentiometers. The transmitter has been calibrated before ex-factory.

4.5.2 Firmware Update
Put the transmitter into a firmware update state. When the firmware needs to be upgraded, it is need to put the transmitter into upgraded mode using this function first. You can update the  firmware by downloading the latest version of the transmitter firmware from your computer or by using the Fly Sky Assistant.

4.5.3 About
In this function, you can view some information, such as the product name, firmware version, firmware release date, and hardware version.

4.5.4 More
See more contact information’s about our company.

4.6 System Setting
Used to set some functions, including Language, Sound, Volume, Standby timeout, Battery type, [LED color, LED brightness, LCD brightness, Contrast, Backlight time and Auto shutdown.

4.6.1 Language
To set the system language, including Chinese and English.
4.6.2 Sound
To set the sound for system and alarm. SYS+ALA means the same sound for system and alarm.
4.6.3 Volume
To set the volume of the sound.
4.6.4 Standby Timeout
To set the time of the standby timeout or whether to enable the standby timeout function.
4.6.5 Battery Type
To set the battery type.
4.6.6 LED Color
To set the color of the LED, or to turn off the LED.
4.6.7 LED Brightness
To set the brightness of the LED.
4.6.8 LCD Brightness
To set the brightness of the LED.
4.6.9 Contrast
To set the contrast of the LCD.

4.6.10 Backlight Time
To set the time of the backlight, namely how long the screen takes to turn off when not in use.
4.6.11 Auto Shutdown
To set the time of auto shutdown, and enable or disable it.

Product Specifications

5.1 Transmitter Specification

400m (water distance without interference) for external antenna
Low Voltage Alarm| Battery Capacity <20%
Antenna Type| Two Antenna(one bulit-in antenna and one external antenna)
Dlspaly| 12864 LCD (Black and white dot matrix screen) .
Battery| 1.5AA4 / 2S Lipo (JST)
Temperature Range| -10°C – +60°C
Humidity Range| 20%– 95%
Languages| Chinese, English
Charging Port| None
Color| Black
Dimensions| 176210.982.5mm
Weight| 420g
Online Update| Yes
Certifications| CE, FCC ID:: N4ZST800

5.2 Receiver Specifications

Certifications

6.1 CE Warning
The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co- located or operating in conjunction with any  other transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.
6.2 FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection  against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televison reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must  accept any interference received, including interference that may cause undesired operation.
Caution!
The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the  equipment.

1. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-lacated or operating in conjunction with any other transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.
2. Move all your channels to the desired position.
3. Select [All channels] and then [Yes] in the confirmation box.

6.3 Environmentally Friendly Disposal
Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle  valuable raw materials and the treatment of toxic substances.

| |
---|---|---
https://space.bilibili.com/439932670| http://www.flysky-cn.com/| https://www.facebook.com/flyskyrc/

www.flysky-cn.com
Copyright ©2023Flysky Technology Co., Ltd.
Release date:2023-03-28
FCC ID：N4ZST800
FCC ID: 2A2UNBR0100

Manufacturer：ShenZhen FLYSKY Technology Co., Ltd.
Address: 16F, Huafeng Building, No. 6006 Shennan Road, Futian District, Shenzhen, Guangdong, China

References

• Flysky

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>