ALTA WINDOW FASHIONS Roller Shades Skyline Shades with Fascia Instruction Manual

ALTA WINDOW FASHIONS Roller Shades Skyline Shades with Fascia

Important: Make sure the mounting surface is level. Brackets must be in line and level for shade to operate properly. Shim brackets if necessary.

Install the Brackets

• Inside Mount (IB), Install each bracket with two screws either through the side or up through the top. Make sure all brackets are leveled and aligned.
• Outside Mount (OB), Secure each bracket with two screws. Make sure all brackets are level. Minimum 1 1/4” mounting surface height requirement.

Install the Shade

• Install the Shade****  

  * First, attach chain diverter into the clutch bracket by gently pulling down. Insert the hooks on the clutch straight into the two slots in the bracket. Once the two hooks are through the slots, gently pull down on the clutch until the hooks have locked securely to the bracket. Then, place the spring loaded pin end into the round hole of the bracket.![ALTA WINDOW FASHIONS Roller Shades Skyline Shades with Fascia-fig5](https://manuals.plus/wp-content/uploads/2022/09/ALTA-WINDOW-FASHIONS-Roller-Shades-Skyline-Shades-with-Fascia-fig5.png)
  * Once the roll has been installed, align the chain in the diverter as shown. This allows room for fascia attachment. For SL10 & SL15 (A), attach the chain diverter cover. If needed, secure the cover with screws. The Clutch SL20 (B) does not require a cover.

• Skyline Clutch 4” Fascia****  

First, place the spring loaded pin end into the round hole of the bracket. Then, keeping the pin end secure in its bracket, insert the hooks on the clutch straight into the two slots in the bracket. Once the two hooks are through the slots, gently pull down on the clutch until the hooks have locked securely to the bracket. The bottom of the clutch should point straight down.

• Agile Lift****  

Important: Do not to pull the lock pin until shade is securely assembled onto the brackets.
First, place the spring loaded pin end into the round hole of the bracket. Then, keeping the pin end secure in its bracket, insert the hooks on the control head straight into the two slots in the bracket. Once the two hooks are through the slots, gently pull down on the control head until the to hooks have locked securely to the bracket. Lastly, remove the lock pin prior to operation by pulling it down.
Note: If for any reason needs to make an adjustment on the position of the installation brackets or remove the shade; raised the shade and insert the lock pin prior to disengaging the shade from the installation brackets.

Install the Fascia

• 3” Fascia****  

First, position the fascia top ridge into the front top channel of all brackets. Then, rotate the bottom front of the fascia downwards until the bottom rear of the fascia snap into the bracket. Finally, attach the bracket covers.

• 4” Fascia****  

First, attach the fascia clip to both brackets, as showed. Then, position the fascia top ridge into the front top channel of all brackets. Rotate the bottom front of the fascia downwards until the bottom rear of the fascia snap into the fascia clip. Finally, attach the bracket covers

Extra Features

• Level Adjust for 4” Fascia Only****  

Note: In some installations, due to leveling issues, the shade may “telescope”. This is not considered a defect.
The 4” fascia offers an optional adjuster bracket with screws that allow the shade to raise or lower ensuring a perfect leveled installation. Once leveled, the shade should stop telescoping.

• 2-on-1 Shades
  Please refer to Roller Shades – Skyline 2-on-1 / Coupled Shades Installation Instructions.

Installing the Beaded Cord Tensioner (Clutch Option Only)

Pull tension device down until the chain is taut and then move the tension device up approximately 1/8”. Mark the upper and lower screw hole and install the device with the screws provided. Important: Do Not Over-Tighten.

Removing the Shade (Only If Necessary) — Removing the Fascia

First, rotate upward to disengage the fascia. Then, gently pull up the control unit (Clutch, Motor or Spring) until the hooks touch the top part of the bracket slot. Pull the shade towards the spring loaded pin end until the hooks are complete out of the bracket slots. Finally, remove the spring loaded pin end from the idler bracket.

Child Safety

Young children can STRANGLE in cord loops and in the loop above the cord stop. They can also wrap cords around their necks and STRANGLE.

•  Always keep cords out of children’s reach.

• Move cribs, playpens and other furniture away from cords. Children can climb furniture to get to cords.

• Do not tie cords together.

• Make sure cords do not twist together and create a loop.
  WARNING

  • STRANGULATION HAZARD – Young children can be strangled by cords.
  • Immediately remove this product if a cord longer than 22 cm or a loop exceeding 44 cm around becomes accessible. Rev 7/21 Print 7/21

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>