ALTA WINDOW FASHIONS Bliss Bridge USB User Guide
- June 11, 2024
- ALTA WINDOW FASHIONS
Table of Contents
ALTA WINDOW FASHIONS Bliss Bridge USB
Introduction
Step 1
Please scan the QR Code below to download the BLISS app.
Scan the QR code to download the app on on the Apple Store.
Scan the QR code to get the app on Google Play.
Step 2
Please scan the QR Code below for additional videos on linking the BLISS Bridge with your home Wi-Fi router, setting up the BLISS app, and establishing a connection with other loT app1ications
Additional Videos
Additional Guides
Please scan the QR Code for additional BLISS programming and setup guides.
BLISS BRIDGE USB
Product Parameter
| Input Voltage | SV DC (USB Type A) |
|---|---|
| Input Power | l000mA |
| WiFi Network | 2.4Ghz only (802.1 lb/n/g) |
| Shade Control Frequency | 433.92 Mhz |
| Range | 30 meters or 98 feet |
| Protection Class | IP20 |
| Operation Temperature | 32″ F to 104 ° F (0° C to 40″ C) |
Status Indicator
| Color | Meaning | Duration |
|---|
| Constant Blue| Workfng fine| Constant
| Slow Flashing Red| Wi-Fi is disconnected|
Continuously till status change
| Slow Flashing Yellow| Wi-Fi is connected|
Continuously till status change
| Quick Flashing Red| Bridge reset| 5 times
| Slow Flashing Purple| Pairing underway|
Continuously till status change
| Slow Flashing Green| Upgrade in progress| Continuously till status change
Declarations
U.S. Radio Frequency FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
ISED RSS Warning:
This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
FCC SAR Warning:
RF Exposure Information (SAR): The SAR limit of USA (FCC)is 1.6W/Kg averaged
over one gram of tissue.
Product Type: BLISS Bridge (FCC ID: 2AU29AMPRFWIFIUSB) has also been tested
against this SAR limit. The device was tested for typical body-worn operations
to keep the BLISS Bridge at least 5mm from the body. When worn on body must be
correct back clip for this product, use of non-approved accessories may result
in exposure levels which exceed the uncontrolled environmental RF exposure
limits
FCC SAR Warning:
The SAR limit of IC is 1.6W/Kg averaged over one gram of tissue. Product Type: BLISS Bridge, model number: BLISS Bridge Wifi and RF (IC: 25624-AMPRFWIFI) has also been tested against this SAR limit. The device was tested for typical body-worn operations to keep the BLISS Bridge at least 5mm from the body. When worn on body must be correct back clip for this product, use of non-approved accessories may result in exposure levels which exceed the uncontrolled environmental RF exposure limits.