ALTA WINDOW FASHIONS Roller Skyline Valance Cornice Instruction Manual

June 3, 2024
ALTA WINDOW FASHIONS

ALTA WINDOW FASHIONS Roller Skyline Valance Cornice Instruction Manual
ALTA WINDOW FASHIONS Roller Skyline Valance Cornice

Install the Brackets — Fabric Cornice

Important: Make sure the mounting surface is level. Brackets must be in line and level for shade to operate properly. Shim brackets if necessary.

Fabric Cornice — Inside Mount
Mounting Instructions

Inside Mount Screws Required


Width|

# of Screws

12” – 28”

| 3
28 1/8” – 52”|

4

52 1/8 – 76”

| 5
76 1/8” – 100”|

6

100 1/8” – 120”

| 7
120 1/8” – 144”|

8

First, center the cornice in desired location. Mark 2” from each jamb for screw location. Mark the mounting surface using a pencil. Then, center the marks in the bracket slots. Space screws evenly, but no more than 24” apart. Finally, drill screw holes.
IMPORTANT: Use drywall anchors when mounting into drywall. Install the cornice through the slotted angle bracket to the mounting surface with the #8 x 1-1/4” screws provided. To install shade behind the valance – refer to Roller Shades – Skyline Open Roll installation instructions

Fabric Cornice — Outside Mount
Mounting Instructions

Inside Mount Screws Required


Width|

# of Screws

12” – 28”

| 2
28 1/8” – 52”|

3

52 1/8 – 76”

| 4
76 1/8” – 100”|

5

100 1/8” – 120”

| 6
120 1/8” – 144”|

7

First, attach the returns to the valance and check the angle on each return. Then, fasten short screws into the valance. Repeat for opposite return.
If ordered custom returns under Fabric Cornice Only (without shade), place the 8” bracket on top of the slotted angle next to the return. With the back of the bracket flush with the back edge of the return, mark the cut mark just past the screw hole that lines up with the slotted angle. Then cut the bracket at the mark.

Measure distance from top edge of cornice to the first complete hole in the slotted angle. Use that measurement to mark the location for the first bracket at the desired height. Repeat for the opposite bracket. Space brackets evenly, but no more than 24” apart. Install the brackets level and aligned to each other, using the screws provided. Using the bolts and nuts provided, attach the slotted angle on top of the installation brackets. To install shade behind the valance – refer to Roller Shades – Skyline Open Roll installation instructions.

Install the Dust Cover (Outside Mount Only)

Note: Dust cover only comes with cornice 1-1/2”, 4” & 6” return.

7/8” Dust Cover
Dust Cover Installation

First, remove adhesive backing from square tapes and place the square tapes on slotted angle. Then, put the dust cover on top of slotted angle and press it to secure the adhesive.

3 7/8” & 5 7/8” Dust Cover
Dust Cover Installation

First, snap the dust cover support onto the slotted angle. Then, remove adhesive backing from square tapes and place the square tapes on slotted angle and brackets. Press the dust cover in place to secure the adhesive.

Install the Brackets — Deluxe Valance

Deluxe Valance — Inside Mount
Bracket Installation

First, install the valance and then proceed with shade installation.
The valance can be mounted directly to the top of the window frame, drill vertically through the pre-drilled slots. To install shade behind the valance – refer to Roller Shades – Skyline Open Roll installation instructions.

Deluxe Valance — Outside Mount
Bracket Installation
First, install the brackets level and aligned to each other, using the screws provided. Then, slide the valance under the clips that are on the top of
the installation brackets. To install shade behind the valance – refer toRoller Shades – Skyline Open Roll installation instructions.

Child Safety

WARNING
STRANGULATION HAZARD – Young chidren can be strangled by cords. Immediately remove this product if a cord longer than 22 cm or a loop exceeding 44 cm around becomes accessible.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals