AUDSTER PR-15BAT Professional Amplified Speaker System Instruction Manual
- June 10, 2024
- audster
Table of Contents
PR-15BAT Professional Amplified Speaker System
AUDSTER
Professional Amplified Speaker System
With USB, MMC, FM, BT, REC
Instruction Manual
Thank you very much for buying this speaker box, please kindly read
instruction manual before operating the product
Product: Professional Amplified Speaker System
Model:PR-15BAT
Technical Specification:
1.Amplified plastic loudspeaker.
2.Woofer:15″, 60 Oz, 75mm VC. Tweeter: 44mm Ti driver
3.Frequency response:45Hz-20KHz
4.Sensitivity:98:2dB
5.With USB, MMC, FM, BT and REC
6.Power:5000W
7.Voltage:AC110V/220V
Note:
Please read the entire attached document carefully
before using the device for your reference.
The power supply must match the demand of the device with reliable ground
wire,
All covering signal should be complied with the demand of device.
The device should be equipped far away high temperature, moisture and powerful
electro and magnetic
field.
Please don’t use the organic cleaner but dry soft cloth to clear the device.
When not in use, unplug the unit from the mains.
Set the unit to the lowest volume prior to switching it on.
Only use suitable means of transportation if you want to move the speaker box-
BE WARE OF YOUR
BACK!
- MMC Port
- USB Port
- MIC Level
- Control button of USB. MMC. FM. BT. RECORD REC: RECORD is to put a USB/MMC in the speaker, through MIC/Line in, it could to record the information within the USB/MMC
- Bluetooth light: Red: Indicating searching for Bluetooth name, Blue: Indicating matched
- Remote Window
- LCD Display
- MIC 1 input Microphone input with XLR connector and 6.35 connector line input.
- MIC 2 input Microphone input with XLR connector and 6.35 connector line input.
- MIC EFF
- Stereo Line Input
12.Stereo Line Output
13.Button to switch between line and USB/MMC/FM/BT
14.Graphic Equalizer
Use the function to adjust the high-middledow effect
15.Time and Repeat Effect
16.Master Level
17.MP3 and Line Level
Adjust this knob, you can reach the effect you want.
18.Volume control of wireless microphone
19.Antennas of Wireless microphone
20.0N/OFF button
When it is on status, the wireless microphone could work; when it is off, the
microphone couldn’t work.
21.MIC Priority selection
When it is on status: MIC Priority could work(When the volume of microphone
reaches a certain
loudness, the loudness of music will decrease); Whe it is off: MIC Priority
couldn’t work,
22.Voltage Switch
23.Power Socket
24.Power Switch
25.Battery Fuse
26.Speaker Output
27.Battery indicator
28.DC Input/DC Output
Federal Communications Commission (FCC) Statement. This device complies with
part 15 of the
FCC Rules. Operation is subject to the following twoconditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation. Note: This
equipment has been
tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the
FCC Rules. These limits are designed to provide Reasonable protection against
harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the
user is encouraged to try to correct the interference by one ormore of the
following
measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to
which the receiver is
connected.
•Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications made to this device not expressly
approved by NingBo
Lisound Audio Equipment Co., Ltd. may void the FCC authorization to operate
this device.Note:
The manufacturer is not responsible for any radio or TV interference caused by
unauthorized
modifications to this equipment. Such modifications could void the user’s
authority to operate
the equipment.
RF exposure statement:
This device complies with FCC RF radiation exposure limits set forth for an
uncontrolled
environment. The device is installed and operated without restriction.