AUDSTER PR-12BAT Professional Amplifier Speaker System Instruction Manual
- June 10, 2024
- audster
Table of Contents
AUDSTER PR-12BAT Professional Amplifier Speaker System
Product Information
The device complies with the Federal Communications Commission (FCC) Radio Frequency (RF) radiation exposure limits for an uncontrolled environment. This means that the device can be safely installed and operated without any restrictions.
Product Usage Instructions
When using the device, it is important to follow the manufacturer’s instructions for proper installation and operation. The device should only be used in accordance with the intended purpose as described in the manual. It is also recommended to maintain a safe distance between the device and the user’s body during operation. The user should avoid direct contact with the antenna and keep it away from their head and body. If the device is being used in a public place, it is important to comply with any regulations or guidelines that may apply to RF radiation exposure. This may include following signage or instructions provided by the facility. Overall, the device is safe to use within the FCC RF radiation exposure limits, and following proper usage instructions will ensure safe and effective operation.
Please do as the below battery operating instruction before running the appliance:
-
Make sure the appliance is powered off before installing the battery fuse.
-
Open the fuse cover by tilting downforce.
-
Press the fuse into the fuse holder fully, and close the cover well.
-
Power on, and ready to start the unit.
-
Avoid the battery fuse in connection mode if the device is not used for a long period of time.
-
According to the date of manufacture, please recharge the battery once every 3 months, recommend charging level;:,:75%.
Technical Specification
-
Amplified plastic loudspeaker.
-
Woofer:12″, 50 Oz, 65mm VC.
Tweeter: 34mm Ti driver -
Frequency response: 45Hz-20KHz
-
Sensitivity: 98±2dB
-
With USB, MMC, FM, BT, and REC
-
Power: 4000W
-
Voltage: AC110V/220V
Notes
- Please read the entire attached document carefully before using the device for your reference.
- The power supply must match the demand of the device with a reliable ground wire.
- All covering signals should comply with the demand of the device.
- The device should be equipped far away with high temperature, moisture, and powerful electro and magnetic field.
- Please don’t use the organic cleaner but dry soft cloth to clean the device.
- When not in use, unplug the unit from the mains.
- Set the unit to the lowest volume prior to switching it on. Only use suitable means of transportation if you want to move the speaker box-BE WARE OF YOUR BACK!
FUNCTIONS
-
MMC Port
-
USB Port
-
The control button of the USB. MMC. FM. BT. RECORD
REC: RECORD is to put a USB/MMC in the speaker, through MIC/Line in, it could to record the information within the USB/MMC -
bluetooth light:
Red: Indicates searching for Bluetooth name, Blue: Indicates matched -
Remote Window
-
LCD Display
-
MIC 1 input
Microphone input with XLR connector and 6.35 connector line input. -
Stereo Line Input
-
Stereo Line Output
-
Graphic Equalizer
Use the function to adjust the high-middle-low effect -
Time and Repeat Effect
-
Master Level
-
Effect Leve
-
MP3 and Line Level
Adjust this knob, you can reach the effect you want. -
MIC Priority selection:
When it is on status: MIC Priority could work(When the volume of the microphone reaches a certain
loudness, the loudness of music will decrease); When it is off: MIC Priority couldn’t work. -
Antennas of Wireless microphone
-
ON/OFF button
When it is on status, the wireless microphone could work; when it is off, the
the microphone couldn’t work. -
Volume control of wireless microphone
-
Voltage Switch
-
Power Socket
-
Power Switch
-
DC Input/DC Output
-
Battery FUSE
-
Battery indicator
-
Speaker Output
FCC STATEMENT
Federal Communications Commission (FCC) Statement. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications made to this device not expressly approved by NingBo Lisound Audio Equipment Co., Ltd. may void the FCC authorization to operate this device.
Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
RF exposure statement
This device complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. The device is installed and operated without
restriction.
CONTACT
- Falcon Sound & Lighting
- Web: www.AUDSTER.com.
- Email: lnfo@AUDSTER.com.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>