FLYSKY FS-R11P Receiver User Manual

: June 10, 2024
: Flysky

Table of Contents

Introduction
Overview
Specifications
Binding
Firmware update
Failsafe
Certifications
Documents / Resources

FS-R11P Receiver
User Manual

Introduction

FS-R11P based on ANT protocol is a receiver which provides 11-channel and bidirectional transmission, featuring external single antenna and PWM, PPM, i-BUS or S.BUS signal output, and a compact design. It can adapted to a variety of model cars or boats.

Overview

FLYSKY FS-R11P Receiver

CH1/P (PWM/PPM)
CH2
CH3
CH4
CH5
CH6
BIND Interface
VCC/BVD(Power Supply /Battery Voltage detection Interface)
CH7
CH8
CH9
CH10
CH11
SENS Interface
SERVO
LED
Antenna
BIND Button
Signal Pin
+ (Power Anode)
– (Power Cathode)
BVD Harness
Connect to Battery Anode
Connect to Battery Cathode

Specifications

Product Name: FS-R11P
Adaptive Transmittes: FS-G11P( Adapts transmitters with ANT protocol)
Adaptive Models: Cars or boats
PWM Channels: 11
RF: 2.4GHz ISM
Maximum Power: <20dBm (e.i.r.p.) （EU）
Antenna: External single antenna
Distance: ≥ 300m (Ground distance without interference)
2.4G Protocol: ANT
Resolution: 4096
Data Output: PWM/PPM/i-BUS/S.BUS
Input Power: 3.5 ~ 9V/DC
Working Current: 66mA/5V
Online Update: Yes
Temperature Range: -10℃ ~ +60℃
Humidity Limit: 20% ~ 95%
Water Proof: PPX4
Dimensions: 37.0mm25mm13.3mm
Weight: 10g
Certifications: CE, FCC ID: 2A2UNR11P00

Binding

The receiver supports two -way binding and one-way binding, and can be set at the transmitter side. The transmitter will display the information returned from the receiver after the two-way binding is completed.
Follow the steps below to bind in two-way binding:

Select [ANT 2 WAY] for RF standard of the transmitter, then put the transmitter in bind mode.
The receiver supports three ways to enter bind mode: BIND button binding, bind cable binding and BIND button binding after power-on.
• BIND button binding: Press and hold the BIND button of the receiver while powering on the receiver, tthe LED of the receiver should be flashing, indicating that the receiver is in bind mode. Then release the BIND button.
• Bind cable binding: Insert the bind cable to the BIND interface of the receiver, then power on the receiver. The LED of the receiver should be flashing, indicating that the receiver is in bind mode. Note that you need to remove the bind cable from the receiver after the binding process is finished.
• BIND button binding after power-on: The receiver has not been connected to the transmitter when it is powered on. Press and hold the BIND button for 3 seconds, the LED of the receiver should be flashing, indicating that the receiver is in bind mode. Then release the BIND button.
When the LED of the receiver is solid on, the binding process should be finished. The transmitter exits the bind mode automaticlly.
Check to make sure the transmitter and receiver functions are working correctly, repeat steps 1 to 3 (binding process) if any problems arise.

Follow the steps below to bind in one-way binding:

Select [ANT 1 WAY] for RF standard of the transmitter, then put the transmitter in bind mode.
Put the receiver in bind mode ( Refer to the description above for entering bind mode).
After the receiver LED becomes slow flashing, then put the transmitter to exit the binding state. At this time, the receiver LED is solid on indicating the binding is successful.
Check to make sure the transmitter and receiver functions are working correctly, repeat steps 1 to 3 (binding process) if any problems arise.

Firmware update

The firmware of this receiver can be updated via the FlyskyAssistant (Only version 3.0 or later is supported. The firmware of FlyskyAssistant is
available on the Flysch official website).
This receiver can be updated through the following two ways:

After the binding between the transmitter and the receiver (the LED of the receiver is solid on), connect the transmitter to the computer, then open the FlyskyAssistant on the computer to update the firmware.
Connect the transmitter to the computer. Then put the receiver to enter the forced update mode by referring to the following three ways (The LED of the receiver works in three-flash-one-off mode repeatedly). Afterwards, open the FlyskyAssistant on the computer to update the firmware.

Power on the receiver while pressing and holding the BIND button for more than ten seconds, until the LED of the receiver works in three- flash-one-off mode repeatedly, then release the BIND button.
Power on the receiver first, then press and hold the BIND button for more than ten seconds, when the LED of the receiver works in three lash-one-off mode repeatedly, then release the BIND button.
Connect the bind cable to the signal pins of the CH5 and BIND interface, then power on the receiver.

Failsafe

The failsafe function is used to output the channel value according to the out-of-control protection value set by the user after the receiver loses its signal and is out of control to protect the model and personnel.
It can also be set failsafe for each channel respectively. This receiver supports two failsafe modes: ON and OFF OFF It is no output for the interface of i-BUS/PPM/PWM.
ON Outputs the failsafe values set for the interface of i-BUS/PPM/PWM.
Notes:

Because the S.BUS signal information contains failsafe flag bits, the failsafe information can be transmitted to the subsequent devices by the failsafe flag bits ruther than by OFF state. The subsequent devices gives response according to the analysed information for the failsafe flag bits.
For the signal PWM/PPM/i-BUS without failsafe flag bits, it supports the setting of the output signal to OFF in case of failsafe, transmitting the failsafe information to the subsequent devices by OFF state.

Attentions:

Make sure the product is installed and calibrated correctly, failure to do so may result in serious injury.
Make sure the receiver’s battery is disconnected before turning off the transmitter, failure to do so can result out of control.
Unreasonable setting of the Failsafe may cause accidents.
Make sure the receiver is mounted away from motors, electronic speed controllers or any device that emits excessive electrical noise.
Keep the receiver’s antenna at least 1cm away from conductive materials such as carbon or metal.
Do not power on the receiver during the setup process to prevent loss of control.

Certifications

FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by taming the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

EU Dock Declaration
Hereby, Flysch Technology co., ltd] declares that the Radio Equipment [FS- R11P] is in compliance with RED 2014/53/EU.
The full text of the EU Dock is available at the following intermit address: www.flyskytech.com/info_detail/10.html

RF Exposure Compliance
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 centimeters between the radiator and your body.

Environmentally friendly disposal
Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances.

FCC ID: 2A2UNR11P00

| http://weixin.qq.com/r/8UiKkvbEAKt-rbLx9x3j
---|---
| https://space.bilibili.com/439932670
| http://www.flysky-cn.com/
| https://www.facebook.com/flyskyrc/

Manufacturer：ShenZhen FLYSKY Technology Co., Ltd.
Address: 16F, Huffing Building, No. 6006 Shenna Road, Fustian District, Shenzhen, Guangdong, China
Figures and illustrations in this manual are provided for reference only and may differ from actual product appearance. Product design and specific

http://www.flysky-cn.com
Copyright ©2022 Flysky Technology Co., Ltd.