novostella NTF81 Smart Flood Light User Guide
- June 10, 2024
- novostella
Table of Contents
Smart Flood Light User Guide
Contact Us
Have some issue? No worries! Please reach us via these channels.
Our customer services team is more than happy to help.
Smart Flood Light User Guide
Before installation, let’s know how the whole thing works.
Step One:
Install the smart flood light. Step Two: Fundamental setup
• Connect smart LEO flood light to Smart Life App. Step Three & Four: Optional
set-up – Connect Smart life App to Amazon Alexa or Google Assistant.
After completing Step Two, you can remote control the light on Smart Life App.
After completing Step Three and Four, you can voice control the light with
Alexa or Google Assistant. This manual consists of Four parts.
Part One – How to Install the light ? 3 – 7
Part Two – Now to pair the light to Smart Life app? 8 -11
Part Three • How to control the light with Amazon Alexa? 12 • 14
Part Four- Now to control the light with Google Assistant? 15 • 16
Part One – How to install the light ?
Warning (1) Please check if the light and the parts are intact before
installation. (2) Make sure to cut off power before installation. (3) Please
do not place this light In corrosive conditions. (4) If there Is any damage to
the cord, please cut off the power and stop using it immediately. (5) Please
do not retrofit the light within the warranty period. (6) To ensure the light
works property, please use the voltage indicated on the packing.
Parameters
| Model | NTF80 | NTF81 | NTFS2 |
|---|---|---|---|
| Wattage | 30 W | 60W | 100W |
| Input Voltage | US: 120VAC | ||
| Color | RGB | ||
| Frequency | 50/60Hz | ||
| Waterproof Rating | 1P66 | ||
| Beam Angle | 120° | ||
| Working Temperature | -20-40°C |
PIN: raF800/NTRIBMTP320-RG6 Operatic., Frerquency.2402-2480 MHz(BLE IM) 2412.2462 MH4802.111:40 ht20)WIFI 2422-2452 MHz(13021In 111443)V1F1
Components
Note: Cord – typeV attachment. For type V attachment: If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar Qualified person in order to avoid a hazard.
Dimension
Installation
Step A: According to the spacing of two screw bits on the bracket, drill two holes on the mounting panel.
Step B: Aim the bracket at the holes and fix it with two bolts.
Step C: Adjust the lighting direction up or down as per your need and plug in
to power the light on.
Note:
Limitation of Indoor and Outdoor Use
- This light is waterproof and damp proof. It is protected against the rain, but it cannot be immersed in water.
- The mounting position of this light should be able to bear at least 10 times as heavy as the light.
- This light should be used in condition that is good for heat dissipation. Its working temperature should be less than 40°C Too high the working temperature will cause serious lumen depression and affect lifespan of the light.
The light source of this luminaire is not replaceable, when the light source
reaches its end of life the whole luminaire shall be replaced.
Note:
01 Make
sure that the distance between the light and the object being its is more than
1 meter, so as to avoid high temperature caused by short distance.
FCC ID: 2AWONNTROC
Federal Communication Commission(FCC)Statement for Users Warning: Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment. This device complies
with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may
cause undesired operation. This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna. – Increase the separation between
the equipment and receiver. – Connect the equipment into an outlet on a
circuit different from that to which the receiver is connected. – Consult the
dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement: This equipment complies with FCC
radiation exposure limits set forth for an uncontrolled environment . This
transmitter must not be coylocated or operating in conjunction with any other
antenna or transmitter. This equipment should be installed and operated with
minimum distance 20cm between the radiator &you body.
Part Two — How to pair the light to Smart Life app?
Step A : Smart Life app installation Please choose either way below to
download and install the app. (1) As per your phone system, choose the QR code
to scan.
(2) Search keyword ‘Smart Life’ in Apple Store or Google Play.
|
---|---
https://itunes.apple.com/cn/app/smart-life-smart-living/id1115101477?l=en|
https://play.google.com/store/apps/details?id=com.tuya.smartlife
Step B: Create an account on Smart Life and login.
Note: Please keep your account and password in mind for Alexa or Google
Assistant App pairing later.
Step C: Add the light to Smart Life App 1. Tap ‘+’ button on top right corner
to add device, then tap ‘lighting’ to enter next page.
2. WiFi
Connection
This smart light only supports 2.4GHz WiFi network, not 5.0GHz. Please make
sure your working network is 2.4GHz, and your phone is connected to the
required WiFi network. (1) Power on the light with your own switch. (2)
Observe how frequently the light blinks to identify which mode it is in. –
Smart Life App supports two WiFi connections, EZ (Easy) Mode and Access Points
(AP) mode. When in EZ Mode, the light blinks rapidly (about 0.5s per blink);
when in AP mode, the light blinks slowly (about 3s per blink). – EZ Mode is
the easier way for WiFi connection. When the light is in AP Mode, you can
change it to EZ Mode by repeatedly turn on-off-on-off-on the switch to
activate the light into rapid blinking status (about 0.5s per blink). And
please make sure to keep an interval over 2 seconds between each turn-on and
turn-off. (3) Confirm the light is in EZ Mode, then tap ‘confirm’ button to
proceed. If you need help, tap ‘view help’ for more details.
Step D : Give a name to the light.
– A simple name is recommended for easier voice recognition with Alexa or
Google Assistant.
– The name given to the light will be the same for voice control on Alexa or
Google Assistant. For example, the light is named ‘smart light’ on this user
guide.
Step E : The named light will be shown on the app homepage.
Now you can control the light (turn on/off, change colors, adjust brightness
ect) with Smart Life on the setting page. Turn on or off the light by tapping
the bulb icon.
Note: To control the light with Amazon Alexa, please read Part Three. To
control the light with Google Assistant, please read Part Four directly.
Part Three — How to control the light with Amazon Alexa?
Please make sure that your Alexa app is connected to Echo, and both work well
under your WiEi network.
Step A : Log in your Alexa App, tap top left corner, and tap ‘Skills’.
Step B :
Type ‘Smart Life’, find ‘Smart Life’ from the search result and tap it to
enable the skill. 
Step C: Enter your Smart Life App account and password. Tap ‘link Now’, then
tap ‘Authorize’ on the next page to bind Smart Life account to Alexa.
Step D : When your Smart Life account is bound to Alexa, tap ‘DISCOVER
DEVICES’ to detect the light. Step E : When the named light is paired to Alen
from Smart Life, it will show on the device page (see the ‘smart light’
example ).
Step F : Now you can control the light with Alexa App on the setting page. To
turn on or off the light, simply tap the bulb icon.
Step G : You can also voice control the light with Alexa by giving these com-
mands: “Alexa, turn on ‘device name’ “, “Alexa, set ‘device name’ to ‘color’
“, “Alexa, set ‘device name’ to ‘number’ “. Device name is the one you give to
the light. The light is named ‘smart light’ in this user guide. For example,
“Alexa, turn on ‘smart lIght “, “Alexa, set ‘smart light’ to ‘blue’ ” etc.
Note: To control the light with Google Assistant, please continue to read
Part Four.
Part Four — How to control the light with Google Assistant?
Step A : Login Google Assistant App, tap ‘Home Control’ on the left side bar
page.
Step B: Tap button on the bottom right to enter next page.
Step C: Find ‘Smart Life’ from side bar list. Step D : Enter your Smart Life
App account and password to bind Smart Life account to Google Assistant. Step
E : You will find the named light shows on the Home Control page. Now you can
control the light on Google Assistant App, or voice control It by giving these
commands: “ok Google, turn on ‘device name’ “, “ok Google, set ‘device name’
to ‘color’ “, “ok Google, set ‘device name’ to ‘number’ “. Device name is the
one you give to the light. The light is named ‘smart light’ in this user
guide. For example, ‘ok Google, turn on ‘smart light’ “, ‘ok Google, set
‘smart light’ to ‘blue’ ” etc.
THANK YOU for choosing Novostella. It is pretty easy to set up this light by
taking a few minutes to watch the step-by-step tutorial video. And for those
who prefer to have a manual at hand for set-up, you may also read the rest
pages for details.
Video Guide
Please scan the left QR code below, choose the language to watch the
installation on Youtube.
Before installation, please note:
+ This product only supports 2.4GHz WiFi network, not 5.0GHz.
+ Make sure to keep an interval over 2 seconds between each turn-on and turn
-off during the set-up.
General Troubleshooting
Scan the right QR code below for FAQ. If your problem is not yet solved,
please write us email via
support@novostella.net.
|
---|---
https://www.youtube.com/playlist?list=PLCQnjkV2wdpqrfS6apyxPbG55Pc5eTlDl|
https://www.novostella.net/pages/smart-floodlight-installation
support@novostella.net
www.novostella.net
[P+ we are social. Get connected I
@Novostella_US 0 @novostella_official c
@novostella_official
f fb.com/novostella.fans
@Novostella_officia I
E-manual
https://www.novostella.net/pages/wi-fi-smart-flood-light-user-manual-version-
ii
Step 1: Scan the QR code
Step 2: Click E-manual PDF file Step 3: Read file online or download Go paper-
free, make life easier, and do something good for the environment.
Manual Version: NTF808/NTF81B/NTF82B-RGB-US / V1.1
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>