saxby lighting 95544 HeroPro CCT Step Dimming Emergency Instruction Manual

saxby lighting 95544 HeroPro CCT Step Dimming Emergency

Product Information

The Stepped Dim Microwave Movement Sensor is a multi-function sensor that is designed to detect movement using microwave technology. It is fitted with a stepped dim feature that allows for customizable dimming levels based on the amount of movement detected. The sensor comes with the following specifications:

• DC Input Voltage: The voltage required to power the sensor.
• Rated Voltage: The optimal voltage for the sensor to operate.
• Stand-by Power Efficiency: The amount of power the sensor consumes when not in use.
• Operating Frequency: The frequency at which the sensor operates.
• Transmitting Power: The strength of the microwave signal transmitted by the sensor.
• Hold Time: The amount of time the sensor will keep the lights on after detecting movement.
• Stand-by DIM Level: The dimming level of the lights when the sensor is in stand-by mode.
• Stand-by Period: The duration of time the sensor remains in stand-by mode before shutting off completely.
• Detection Area: The area within which the sensor can detect movement.
• Daylight Sensor: A feature that allows the sensor to detect ambient light levels and adjust the dimming level accordingly.
• Detecting Radius: The maximum distance from which the sensor can detect movement.
• Mounting Height: The optimal height at which the sensor should be mounted for best performance.
• Detecting Angle: The angle within which the sensor can detect movement.
• Operating Temperature: The temperature range within which the sensor can operate effectively.

Product Usage Instructions

Follow the below instructions to properly use the Stepped Dim Microwave Movement Sensor:

1. Ensure that the sensor is properly installed and connected to a power source.
2. Adjust the stand-by DIM level to the desired dimming level for when the sensor is in stand-by mode.
3. Set the hold time to the desired duration for how long the lights should remain on after detecting movement.
4. Adjust the detecting radius and angle to ensure that the sensor is detecting movement within the desired area.
5. Activate the daylight sensor feature if desired to allow the sensor to adjust dimming levels based on ambient light levels.
6. Ensure that the operating temperature is within the specified range for best performance.
7. Test the sensor to ensure that it is properly detecting movement and adjusting dimming levels as desired.

Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product. Please retain these instructions for future reference.

Warning
This light fitting is double insulated and does not require connection to an earth circuit Please read these instructions carefully before commencing any work. This unit must be fitted by a competent and qualified electrician. Install in accordance with the IEE Wiring regulations and current Building Regulations. Check the pack and make sure you have all the parts listed To prevent electrocution switch off at the mains supply before installing or maintaining this fitting. Ensure other persons cannot restore the electrical supply without your knowledge. If you are in any doubt, please consult a qualified electrician. This light fitting should be connected to a circuit with a 30mA RCD fitted. If replacing an existing fitting, make a careful note of the connections. Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

Technical data

• Supply Voltage: 220-240 V~, 50 Hz
• Bulb Type: 18/14/9W LED module (SMD) CCT, 3000/4000/6000K This product contains a light source of energy efficiency class D.

Conformity with all relevant UKCA Directive requirements. Conformity with all relevant EC Directive requirements The power supply is Double Insulated and does not require
connection to an Earth circuit. Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice.

• This product is not suitable for dimming.
• This product is rated at IP65
• This product is rated at IK10.

Battery parameters:

Lumens| 120Lm in EM mode
Duration| 3 hours (180 Minutes)
Operating Temperature| 0ºC – 50ºC
Maximum Operating Humdity| 90%
Change over time| Approximately 1s
Battery Specification| LifePO4 3.2V 1500mAh
Battery Charge Time| 24 Hours
Battery warranty| 2 years

Layout

Plan the desired layout of these fittings carefully, ensuring the cables will reach the distances between each light fitting. Avoid locating any cables in positions that would cause a hazard. Position cables and junction boxes (not supplied) away from areas where they may be at risk from being cut, trapped or damaged. The mains supply cable must have a minimum cross section area of 1.0mm2. Cables must be protected using suitable conduit or plastic trunking. The products can be wall or ceiling mounted. If wall mounting ensure that the power supply is at the bottom

Installation

Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully note the position of each set of wires. Note that the switch is turned off before installation. The ceiling surface must be flat and smooth to ensure a good fit. Ensure that the screws and cable entry points are sealed to maintain the IP rating of the product.

• Twist and remove the lamp cover from the product, keep safe for refitting later.
• Turn the clip to loose the LED tray in the rear casing.
• Using the rear casing as a template mark the position to drill out the fixing holes. Take care to avoid damaging any concealed wiring and pipes.
• Fix the rear casing into the position using the installation plugs and screws
• Pull the cable through the cable entry hole and seal to maintain the IP rating and wire as detailed Wiring Diagram.
• Unscrewed the battery box cover and then connect the battery DC connector together before commissioning
• Refit the LED tray back into the rear casing and lock the clip.
• Twist the lamp cover back onto the product and lock in place.
• Replace fuse or circuit breaker and switch on. Your light is now ready for use.

The wattage is changeable between 18/14/9W using the wattage switch on the driver before installation. The colour is changeable between 3000/4000/6000K using the CCT switch on the driver before installation.

Choose your preferred wattage and colour before installing by wattage switch or CCT switch on the driver.

Note : Befeore you change the wattage or colour, please turn off the power switch for safety.

Product images may vary.

Bezels
The following individual casings are available for purchase separately.

• 95545 : Chrome plain
• 95548 : Black plain
• 95551 : Anthracite grey plain
• 95546 : White eyelid
• 95549 : Black eyelid
• 95552 : Anthracite grey eyelid
• 95547 : White grill
• 95550 : Black grill
• 95553 : Anthracite grey grill

Wiring

• This product is double insulated and must not be earthed. If there are any incoming earth cables, they must be joined together and well insulated with good quality insulation tape. This is to ensure earth continuity throughout your property
• Having correctly identified the wiring from your existing light fitting, connect to the quick fit connection block in the following way, using the supplied link cables where necessary.

Check that…

• You have correctly identified the wires.
• The connections are tight.
• No loose strands have been left out of the connection block

Stepped Dim Microwave Movement Sensor

This product is fitted with a stepped dim microwave movement sensor. Please see below detailed operating instructions.

MULTI-FUNCTION SENSOR SPECIFICATIONS

Detection area is effected on volume of motion object and motion speed. The detection area is tested by a 165cm height person and walking speed is 0.3m/s.

FUNCTION

• The light keeps off during daytime even when movement is detected. (Ambient lux level is above preset daylight threshold)
• With movement and insufficient ambient lux level, the light is triggered on 100% by the detector
• If there is no more movement, the light dims to stand-by dimming level after hold-time.
• The light turns off automatically after stand-by time

DIP SWITCH SETTING

1. Sensitivity
   Sensitivity can be adjusted by selecting the combination on the DIP switches for different applications.

2. Hold-time
   Hold-time refers to the time period that the light remains 100% on if no more movement is detected.

3. Daylight threshold
   Different daylight threshold can be preset on DIP switches. Light will always turn on upon movement if daylight sensor is disabled.

4. Stand-by time
   This is the time period that the light remains at a low level before it is completely turned off.

5. Stand-by dimming level
   Light can be dimmed to different levels after hold-time.

Care and Safety

We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the finish. For your safety, always switch off the power supply before cleaning. For further information, please visit https://www.lighting-info.co.uk/95544 www.saxbylighting.com

References

• Saxby Lighting - Commercial and Domestic Lighting Supplier

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>