SOCO CUmini E-Scooter User Manual

SOCO CUmini E-Scooter

USER INSTRUCTION

To ensure your safety, please read this manual carefully before riding and make sure you are always following the requirements below:

1. Fully understand the information in this manual, including but not limited to the relevant instructions, precautions and warnings.
2. Fully understand the operation and contingency measures of CUmini Smart Electric Scooter.
3. Be fully aware of warning labels of CUmini Smart Electric Scooter.
4. Do not disassemble the vehicle or any parts without permission. Please contact customer service department and dealers if you need any replacement or make further purchase.
5. Please keep the user manual in a safe place.
   | All parameters of this vehicle have been permanently set according to the national standard before leaving factory. The company is not responsible, if the original electrical or circuit has changed and caused excess, such as increase the speed.
   ---|---

SAFETY INSTRUCTION

To ensure the safety of you and others, please make sure to observe the following:

1. Don’t lend your vehicle to someone who can’t operate it to prevent any hurts.

2. Juveniles under 16 years old are strictly prohibited to drive electric scootor on the road.

3. Please drive in the bicycle lane and the maximum speed should not exceed 15km/h. (Keep to the right if there is no bicycle lane.)

4. Do not ride on the road after taking medications, drinking alcohol or when you feeling unwell which may affect your riding ability.

5. Observe traffic regulations and traffic signs, according to the provisions of laws and regulations to carry man and cargo. Confirm the surrounding road conditions and vechile condition any time to actively avoid danger.

6. In rainy and snowy weather, braking distance will be extended, please slow down the vehicle. Avoid travelling in bad weather such as storms and typhoons.

7. Wear safety gears, especially helmet. Wear appropriate protective clothing like boots and gloves if necessary.

8. To ensure the safety of you and others, please avoid using the high beam under good lighting conditions. The continuous use of high beam will cause visual obstacles to opposite vehicles and pedestrians and affect the safe driving. In the case of dim light, turn on the lights in time.

9. Please turn off the power immediately and remove the key after riding. Do not allow children play the vehicle to avoid unnecessary losses.

10. Perform a basic check each time before riding.

11. Please pay attention to the safe operation of the electric vehicle:
    a Do not park the vehicle indoors or in the hallway.
    b Do not charge the battery/vehicle indoors or in the hallway. The battery/vehicle should be kept away from combustible materials when charging, and the charging time should not be too long.
    c Please pay attention to the correct usage of the battery and warning labels. Wasted batteries should not be dismantled without authorization, and should be managed and recycled by the relevant professional departments.
    d Please pay attention to the safe usage and the warning labels of the charger. Make sure to use the original charger for the same model.
    e Please be aware of the precautions regarding water washing.

12. Check before riding, if there is an abnormality, please promptly carry out maintenance or find professional repair service:
    a. Check the status of power circuit, lighting circuit, etc.
    b. Check whether the front and rear brakes work properly.
    c. Check whether the handlebars, front and rear wheels are stable.
    d. Check tire pressure.
    e. Check whether the reflectors are stained.
    f. When adjusting handlebars or saddles, make sure not to expose the safety line marks (where applicable)

ACCESSORIES CHECKLIST

Intelligent Remote Control

Quick Start

Key

Wrench for Rearview Mirrors

Charger

INSTALL BATTERY PACK

1. Open the cushion/battery
   

2. Put in the battery pack.
   

3. Plug in the main connector.
   

4. Put back the cushion.
   

STARTING VEHICLE

1. Put on the helmet.
   

2. Get on your CUmini, retract the side stand.
   

3. Press “Unlock” button on the intelligent remote control.
   

4. Press the “Parking” button.
   

5. The vehicle enters READY state.
   

6. Gently twist the throttle to ride on the road.
   

DOWNLOAD APP

CU mini Smart Electric Scooter supports wireless communication, GPS, etc., which can connect the vehicle with your smart phone. You can manage and query your vehicle through SOCO App on your smart phone.

Available on iOS and Android platforms, please check your smart phone operating system before installation.
iOS platform: App requires iOS 9.0 or later.
Android platform: App requires Android 4.4 or later.
Download and install SOCO App by scanning the QR code in the last page of this manual.

SOCO APP

| Since the date of purchase, you will be presented with 1 year’s free data of SIM card to use SOCO APP function.Make sure to recharge it before the free period expires. For those who fail to recharge within the time limit, the operator will close the recharge interface, and the recharge function of data cannot be restored, in which case SOCO APP cannot be used normally.
---|---

PARAMETER TABLE

Main Specifications and Performance Index for CUmini.

Motor Main Specifications

| Motor Type| Permanent Magnet| Permanent Magnet
Rated Power(W)| 350| 350
Rated Rotating Speed (r/min)| 290| 290
Rated Voltage(V)| 48| 48
Controller Main Specifications| Undervoltage Protection Value (V)| 42±1| 42±1
Overcurrent Protection Value(A)| 21±1| 21±1

DESCRIPTION OF COMPONENTS AND PARTS

a. Schematic diagram of vehicle parts

b. Dash Overview

1.  Speedometer/Error Codes
   Display current speed of the vehicle. Display the SoC in percentage. When the error indicator illuminates, it displays error code.

2. Total Mileage/Mileage Per Trip
   Display total mileage and mileage per trip.

3. State of Charge (SoC)
   Display the SoC in percentage

4. Power Display Bar
   Display current amount of energy

5. State of Headlight
   Display the on/off state of headlight.

Error Indicator Display error with error code.

 Battery Error Indicator Flicker when electric quantity is 10%.

OPERATION GUIDE

a. Left Handlebar Control Assy 4

1. Headlight Switch Tap to switch on/off.
2. Turn Signal Switch Turn to left, left turn signal on; Turn to right, right turn signal on, keep in middle, turn signal off.
3. Horn Button Press, horn on; Release, horn off.
4. One-Click Fix

Turn on the power switch, then press the “One-Click Fix”, you can start the self-check operation. If there is a failure such as Hall fault and handle fault, the vehicle can keep driving normally at a low speed.

b. Right Handlebar Control Assy

1. Warning Button
   Press the triangle warning button as shown in the picture to turn on the emergency flasher.

2. Parking Button

3. When the vehicle is unlocked, tap the button to enter the “READY” state, and gently turn the handle to start the vehicle;When the vehicle is stationary, tap the button to enter the locked state.

c. Intelligent Remote Control Operation

CU mini is equipped with second generation SOCO Intelligent Remote Control, with a press of the button, you can lock or unlock the vehicle within effective distance.

d. Open Battery Compartment
Insert the key and turn it clockwise to open the battery compartment

RIDING GUIDE

a. Pre-ride Checklist
Before operating your CUmini Smart Electric Scooter, check the following to ensure your own safety:

1. Check whether the handlebar is stable and flexible when turning.
2. Check whether the left and right handlebar controls work properly.
3. Check whether the throttle control works properly.
4. Make sure the tire pressure is within normal range. The suggested tire pressure is 175-200 kPa for the front tire, and 200- 225 kPa for the rear tire (maximum tire pressure 280Kpa).
5. Make sure that there are no cracks, damage, wear, foreign object puncture or adhesion on the tire surface.
6. Check trend depth of both tires is enough. If the tire is worn to the black shaded mark on the diagram, it needs to be replaced.
7. Check if any error warning sign illuminates on the dash when power on.
8. Check whether the battery capacity is sufficient for your trip.
9. Check whether all lights function properly.
10. Check whether horn function properly.
11. Check whether rearview mirrors are clean and adjust them to appropriate angle.
12. Check whether the handlebar and brake system function properly.

If you have any questions, please contact SOCO Customer Service.

b. Start the vehicle

1. Put on the helmet.
   

2. Get on your CUmini, retract the side stand
   

3. Press “Unlock” button on the intelligent remote control.
   

4. Press the “Parking” button
   

5. The vehicle enters READY state.
   

6. Gently twist the throttle to ride on the road.
   

**TIPS

**

• Before riding, make sure the center stand is retracted.
• You can only start the vehicle when it’s in the stationary state. If an error occurs while riding, please slide or push the vehicle to a safe area.
  Do not attempt to restart the vehicle while riding or in the driving lane to avoid danger.

c. Tips for Riding

1. When the vehicle is starting, you should slowly accelerate in order to avoid excessive starting current caused by instantaneous rapid acceleration and increased energy consumption.
2. Under the premise of ensuring safety, try to maintain a constant speed, reduce frequent start, brake, instant acceleration, etc. to avoid increased energy consumption.
3. The maximum load for CUmini is 75KG. Overloading is strictly prohibited.
4. When pushing the vehicle, please press the “Parking” button or switch to Forward Mode to prevent accidents caused by sudden start of the vehicle due to unintentional turning of the throttle control.
5. Please hold up the center stand while parking, and press the “lock button” of the intelligent remote control.

BATTERY USE INSTRUCTION

Battery Charging 1

1. Open the battery compartment.
2. Disconnect the battery pack main plug.
3. Take the battery pack out of the battery compartment.
4. Put the main plug of the charger into the battery charging port, and then connect the plug to a power supply
5. The indicator illuminates red while the battery pack is being charged normally, and it turns gree when fully charged.

Battery Charging 2

1. Take out the charger.
2. Connect the main plug of the charger with the socket under the seat of the vehicle.
3. The indicator illuminates red while the battery pack is being charged normally, and it turns green when fully charged.
   

Warning:
Battery is strictly prohibited to get wet, flushed,or even submerged in water.Vehicle wading height should not exceed the bottom of the battery compartment, or it will cause the water inflow, short circuit,resulting in permanent battery failure. Under such circumstances, it is strictly forbidden to charge the vehicle or the battery again, otherwise it will cause the danger of internal fire, combustion and explosion. Please immediately transfer the battery to the service center for maintenance.This car is not equipped with air circuit-breaker, perform power-off protection when it is disconnected .

TIPS

1. Charging temperatures: 0 – 40, discharging temperature: -15 – 45 .

2. Charge the battery pack after using, if you plan on not riding the vehicle for a long time, please take the battery pack out of the vehicle.

3. Forbidden to short-circuit the battery pack.

4. Please prevent children from touching the battery pack and forbidden to throw it into the fire.

5. Forbidden to impact or press strongly on the battery pack.

6. Only charge the battery pack with the designated special charger. Do not use unapproved chargers to charge the battery pack.

7. The battery pack and charger have been strictly inspected before leaving the factory, forbidden to disassemble the battery pack without authorization.

8. Do not park the vehicle indoors or in the hallway. Do not charge the vehicle indoors or in the hallway.
   The battery/vehicle should be kept away from combustible materials when charging.

9. Don’t charge in a closed space, under the hot sun, or at high temperature, and the charging is not allowed to perform in the saddle or tailbox;

10. If the indicator is abnormal, odor occurs or the charger shell is overheated in the charging process, stop charging immediately, and overhaul or replace the charger.

11. Used batteries shall not be disassembled without authorization, but shall be collected by relevant departments.

Storage, Maintenance and Transportation

1. If the vehicle is not used for a long time (such as winter, summer or other special circumstances), the battery must be removed and stored separately, and regularly maintained and charged. Otherwise, the battery can be completely drained, causing irreversible damage. Battery failure in such case will not be covered by warranty.
2. In case you plan on storing your battery pack for a long period of time, please disconnect the battery from the vehicle to prevent it from over-discharging. Keep the battery in a dry, ventilated place and fully charge it with the charger once every month.
3. The battery pack and charger should be stored in a clean, dry and well-ventilated place and avoid contact with corrosive substances, and be kept away from power, fire and heat sources.
4. Battery pack storage conditions: ambient temperature 0-25, ambient humidity 65%RH 5 Don’t park the vehicle, or charge the battery/vehicle indoors,and avoid combustible materials when charging.

APP INSTRUCTIONS

CUmini Smart Electric Motorcycle sup ports wireless communication, GPS, etc., which can connect the vehicle withyour smart phone.
You can manage and check your vehicle using your smart phone through the SOCO App.

Available on iOS and Android platforms, please check your smart phone operating system before installation.

iOS platform: App requires iOS 9.0 or later.
Android platform: App requires Android 4.4 or later.

APP main features:’

| On-Board Diagnostics:
When the vehicle is ready to start , you can access the condition of the vehicle by performing a one-button examination.
---|---
| Data Record:
Users can access the vehicle information, battery level, distance travelled, tracking and other information through the APP.
| Anti-theft System:
The vehicle will sound the alarm when an unauthorized movement of the vehicle occurs. The app will notify the owner and track tracking the position of the vehicle.
| Social Networking:
Users can make friends and build the community through the app and enjoy the fun of riding online and offline.

MAINTENANCE

Regular maintenance can improve the service life and driving safety of CUmini Smart Electric Scooter. It is suggested that you take care of the vehicle following advices below:

a. General cleaning and maintenance
Cleaning: Please use clear water and mild detergent to clean the vehicle, and use soft cloths and sponges to clean the surface. Please do not use metal brushes, sandpapers etc. to prevent the parts surface from scratching. After cleaning, dry it with a soft cloth.
Storage: Please move the vehicle to a dry and cool indoor place, reduce exposure to sun and rain to avoid rust and corrosion of parts, thereby prolong the service life of your vehicle.

b. Warnings

1. Please do not use high-pressure washers to flush the vehicle directly, so as to avoid internal electrical parts and lines being exposed to water intrusion and soaking, which may cause vehicle mechanical failure or other potential accidents.
2. Before long-term storage, please disconnect the battery from the vehicle and avoid over discharging, and please charge the battery once a month.

COMMON PROBLEMS AND TROUBLESHOOTING METHODS

a. FAQ and Troubleshooting

1. Battery is poorly connected
2. The fuse is blown or in poor contact

|

1. Please check if the main battery plug is properly connected
2. Please change the fuse

Twist the throttle, the motor won’t start.|

1. Low battery
2. Handle lever is not returned
3. Parking button is not switched off
4. Throttle fault
5. Controller connector is loose
6. Controller fault
7. Motor fault

|

1. Charge the battery
2. Return the handle lever
3. Press the parking button to unpark
4. Replace the throttle
5. Replug the controller connector
6. Replace the controller
7. Replace the motor

Speed is slow or mileage is short.|

1. Low battery
2. Flat tire
3. Overloading
4. Poor braking
5. Battery aging or reaching end of life

|

1. Charge the battery
2. Please inflate the tires to normal pressure before riding
3. Observe load limits
4. Replace brake pads and check the brake system before riding
5. Replace the battery

Battery won’t charge|

1. The charging plug is poorly connected
2. Did not use the correct charger
3. Battery aging or reaching end of life

|

1. Please check if the main plug is properly connected
2. Please use SOCO designated charger
3. Replace the battery

b. Error Codes

service or dealer
Error 98 on Dash| Controller stops working (possibly overcurrent, locked- rotor, under voltage, over temperature)| Please stop for a while and then start again
Error 97 on Dash| Controller power transistor fault| Please contact customer service or dealer
Error 96 on Dash| Controller Hall sensor fault| Please contact customer service or dealer
Error 95 on Dash| Controller throttle fault| Please check the throttle wiring or contact customer service or dealer
Error 94 on Dash| Battery communication fault| Please check the charging port connection, or contact customer service or dealer
Error 93 on Dash| Charging overcurrent| Please stop charging, and check the charger
Error 92 on Dash| Charging overvoltage| Please stop charging, and check the charger
Error 91 on Dash| Battery at high temperature| Please stop charging/riding wait until the battery temperature drops before attempting to ride
Error 90 on Dash| Discharging overcurrent| If it keeps showing Error 90, please stop riding and wait for a moment
Error 89 on Dash| Low temperature charging| Please take out the battery and charge it in a warm indoor place
Error 88 on Dash| Low temperature discharging| Please take the vehicle or battery to a warm indoor place, and wait for a moment
Error 87 on Dash| Internet connection fault| Please move the vehicle to an open area, or contact customer service or dealer
Error 87 on Dash| GPS connection fault| Please move the vehicle to an open area, or contact customer service or dealer

c. Battery Troubleshooting

battery.
In use| Error 88 on Dash| Low temperature discharging| Please move the vehicle to a warm indoor place, and wait for a moment
In use| Error 90 on Dash| Discharging overcurrent| If it keeps showing Error 90, please stop riding and wait for a moment
In use| Error 91 on Dash| High discharge temperature| Please stop riding, switch off the air circuit-breaker and wait for a moment
In use| Error 94 on Dash| Battery communication fault| Please check the charging port connection or contact customer service or dealer
In use| Overnight or next day, the dash shows a drop in power| ECU, controller, alarm electrical components will drain the battery. Normal phenomenon| Operate as normal
In use| The mileage is different from official data| Official Mileage is the one in a special environment and condition, and is related to road conditions, weather, temperature, wind resistance, load capacity and other factors| If you have any questions, please contact customer service or dealer
Storage| Start the vehicle, “Power” not on| Battery has been stored for too long, power is used up| Charge the battery. If it can’t be charged, please contact customer service or dealer
Charging| Error 89 on Dash| Low temperature charging| Take out the battery and charge it in a warm indoor place
Charging| The charger heats up during charging| Charging process of the charger internal current is high and will generate a lot of heat, the metal housing can effectively dissipate heat, which will lead to a higher temperature of the housing| Operate as normal, and use the charger in a dry, ventilated place
Battery flooded water| The battery does not work properly and the vehicle cannot be started| The vehicle is rained on, soaked in water, waded too deep in water, causing battery flooded water| Stop using. Please contact customer service or dealer
Battery shell broken| The battery has been s impacted or dropped, causing the shell to break or crack| Battery shell damage caused by the use of the vehicle| Stop using. Please contact customer service or dealer

SOCO Smart Electric scooter

Android

|

iOS

|

Bind your vehicle

CHECK LIST

Note: Check the lithium battery balance by BMS reading and manual measurement.

Manufacturer:Yanaka (Xuzhou) New Energy Locomotive Co., Ltd.
Address: Accessories Park, Hi-tech Industrial Development Zone, Changdian Town, Fengxian County, Xuzhou City, Jiangsu Province, China
Assembly plant: Changzhou Kwang Yang Motor Co.,Ltd.
Address: No.10 Lvtang Road, New North District, Changzhou City, Jiangsu Province, China
The illustrations in this manual may dier from the actual products.
We reserve the rights to modify drawings and products to improve quality and performance without prior notice.

www.supersoco.com

References

• SUPERSOCO

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>