DIGITUS DN-80112-1 Gigabit Switch Installation Guide
- June 10, 2024
- DIGITUS
Table of Contents
DIGITUS DN-80112-1 Gigabit Switch
16/24-Port Gigabit Switch
Introduction
DN-80112-1 has 16×10/100/1000Mbps RJ45 port, Using store and forward
technology, combined with dynamic memory allocation, to ensure the effective
allocation of bandwidth to each port. This switch is easy to install and does
not require configuration . It is easy to manage and maintain which can meet a
lot of networking environment, such as Business building, Community, Hotel,
Office etc.
DN-80113-1 has 24 10/100/1000 Mbps RJ45 ports, with port 23 and port 24 as the
uplink ports. It uses store-and-forward technology in combination with the
dynamic memory allocation for each port. The integrated VLAN function can
improve the network environment and reduces network maintenance costs. The
DN-80113-1 is easy to manage and maintain.
Main feature
- Flow control for full duplex operation and back pressure for half duplex operation
- Supports VLAN mode (Only for DN-80113-1)
- LED lights for monitoring the operating status and for fault analysis
- Line speed forwarding, smart identification
- Supports jumbo frame up to 9216K bytes
- Line speed forwarding, smart identification
Package Content
- 1x 16/24 Port Switch
- 1x Power Cable
- 1x QIG
- 1x Mounting material
Main Specifications
| Model | DN-80112-1 | DN-80113-1 |
|---|---|---|
| Standard | IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3z, |
IEEE802.3az, IEEE802.3x
Network Media
| 10BASE-T: UTP category 3,4,5 cable (≤100m) 100BASE-TX: UTP category 5 cable
(≤100m) 1000BASE-T: UTP category 5e cable (≤100m)
MAC Address Table| 8K, Auto-learning, Auto-aging
Transfer mode| Store-and-Forward
Frame Forward Rate| 10Base-T: 14881pps/Port 100Base-TX: 148810pps/Port
1000Base-T/X: 1488095pps/Port
Switching Capacity| 32Gbps| 48Gbps
Forwarding Rate| 23.8Mpps| 35.7Mpps
Packet buffer| 4.1M bit
Dimensions (LxWxH)| 280 x 180 x 44 mm
Fan| Fanless
Power Input| AC: 100~240V, 50/60Hz
Temperature| Operating Temperature: 0°C ~ 40 °C (32 °F ~104°F) Storage
Temperature: -40 °C ~ 70 °C (-40 °F ~158°F)
Humidity| Operating Humidity: 10% ~ 90% non-condensing
Storage Humidity: 5% ~ 90% non-condensing
Green energy saving| IEEE 802.3az
MTBF| >50000 hours
Hardware Description
Front Panel
The Front Panel consists of Ethernet Ports. The LED indicators are also
located on the panel.
DN-80112-1
DIP Switch (Only for DN-80113-1)
The DIP switch located on the left panel.
- Default: the factory default mode, can normal communication between port 1~24.
- VLAN: 1-22 port can be isolated each other but 1-22 port can connect to 23- 24 port after open VLAN to stop broadcast storm to increase forwarding rate of frame.
LED indicator
| LED | Color | Function |
|---|---|---|
| PWR | Green | Off: No Power supply. |
Light: Indicates the switch has power.
LNK/ACT
| ****
Green
| Off: No device is connected to the corresponding port.
Light: Indicates the link through that port is successfully established at 10/100/1000Mbps.
Blink: Indicates that the Switch is actively sending or receiving data over that port.
Rear Panel
The rear panel of the switch indicates an AC inlet power socket, which
accepts input power from 100 to 240V AC, 50/60HZ.
Power socket
Connect the female connector of the power cord here, and the male connector to
the AC (Alternating Current) power outlet. Please make sure the voltage of the
power supply meets the requirement of the input voltage
Grounding column
The switch already comes with lightning protection mechanism. For safety
consideration, you should ground the switch through the PE (Protecting Earth)
cable by Grounding Column
Installation the Switch
This part describes how to install your Ethernet Switch and make connections to it. Please follow the following instructions in avoid of incorrect installation causing device damage and security threat.
- Before cleaning the switch, unplug the power plug of the switch first.
- Do not clean the switch with wet cloth or liquid
- Do not place the switch near water or any damp area. Prevent water or moisture from entering the switch chassis
- Do not place the switch on an unstable case or desk. The switch might be damaged severely in case of a fall
- Ensure proper ventilation of the equipment room and keep the ventilation vents of the switch free of obstruction
- Make sure that the operating voltage is the same one labeled on the switch
- Do not open the chassis while the switch is operating or when electrical hazards are present to avoid electrical shocks.
Desktop Installation
Install the Switch on a desktop, please attach these cushioning rubber feet provided on the bottom at each corner of the Switch in case of the external vibration. Allow adequate space for ventilation between the device and the objects around it as example below.
Rack-mountable Installation
The switch is rack-mountable and can be installed on an EIA-19-inch equipment
rack. To do this, first, please install the mounting brackets on the switch’s
side panels (one on each side), secure them with the included screws, and then
use the screws provided with the equipment rack to mount the switch on the
19-inch rack as example below.
Turn on the switch
Please connect the AC power cord into the rear of the switch and to an
electrical outlet (preferably one that is grounded). When the switch is power
on, the LED indicators flash momentarily for one second, which represents a
resetting of the system. The Power LED indicator turns on green.
Note: Please confirm the voltage is correct before power on, otherwise the
switch will be damaged.
(The power input is:100V-240Vac, 50/60Hz.)
This is a Class A product. In home environment, this product may cause radio interference. In this case, the user may be required to take appropriate measures. Hereby Assmann Electronic GmbH, declares that the Declaration of Conformity is part of the shipping content. If the Declaration of Conformity is missing, you can request it by post under the below mentioned manufacturer address.
www.assmann.com Assmann Electronic GmbH Auf dem Schüffel 3 58513 Lüdenscheid Germany
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>