rizoma MI EE146 00 Wiring Kit for Front Turn Signals User Manual
- June 10, 2024
- rizoma
Table of Contents
MI EE146 00 Wiring Kit for Front Turn Signals
User Manual
MI EE146 00 Wiring Kit for Front Turn Signals
Welcome to Rizoma
Before you start
We are pleased to welcome you into the world of RIZOMA, and we congratulate
you for your excellent choice. Please carefully follow the instructions in
this guide, which will allow you to mount and use the product correctly and
enjoy all the features it has. For your protection and safety, RIZOMA
expressly recommends that you have the installation of the product performed
by skilled personnel. Improper installation, repair or maintenance, can cause
accidents. Keep this user guide as a reference for the future. RIZOMA accepts
no liability for any damage, of any kind, which may be caused, directly or
indirectly, to persons or things as a result of incorrect assembly or failure
to observe all the assembly instructions. We also invite you to comply with
the provisions of the Highway Code and Traffic rules and/or to additional
regulations in force in your Country.
General conditions
Attention: This component comes assembled for shipping purposes only.
Tighten all fasteners to appropriate torque specifications before riding.
Descriptions preceded by this symbol contain information, instructions, or
procedures, which, if not followed, may result in death or serious injury.
- Carefully read, understand and follow these instructions, they are an essential part of the product. If you have any doubt whatsoever regarding the installation or use of your RIZOMA product, please see your authorized RIZOMA dealer for assistance (on www.rizoma.com ).
- For correct installation, all tightening has to be done after the correct positioning of the accessories without restricting the moving parts, to not compromise the correct functioning of the product.
- After installing any Rizoma product, please check that all related components of the motorbike function e.g. brakes, throttle, clutch, lights and steering. We strongly suggest to repeat these checks periodically, especially after long trips or prolonged periods of not using the bike.
Your RIZOMA products require regular inspection and maintenance. The more you
ride the more often you must inspect your RIZOMA products. If your products
are leaking, bent, deformed, cracked, chipped or worn, no matter how slight,
immediately have a RIZOMA dealer inspect the products before you ride again.
In any case never try to repair or modify the Rizoma products or their
components, always replace with Rizoma original components.
Rizoma products may not be compatible with your motorcycle or with other
aftermarket equipment installed before. For your safety Rizoma suggests to
always contact your RIZOMA dealer.
O.E.M.: original equipment manufacturer.
Resistor kit for Rizoma front and rear turn signal
N°01 resistor da 100 ohm 2 watt e n°01 resistor 47 ohm 3 watt.
Before you start mounting the product please check the completeness of the kit
on the part list. The difficulty level and the time of assemblage shown do not
include the removal of OEM components. The warrantee is not valid for any
electric wires cutting or any product modify or tampering.
Improper installation could damage the electrical system of the motorcycle and
cause a fire, resulting in personal injury or death. Electrical shock hazard.
Disconnect the battery before starting to install turn license plate bracket
or rear light or the turn signals. The pins must always be isolated and
respect the polarity in the connections. The warrantee is not valid for any
electric wires cutting or any product modify or tampering.
| DIFFICULTY LEVEL| Simple
---|---|---
| TIME OF ASSEMBLAGE| 3-5 min
INSTALLATION
Step 1
Your guarantee will not apply if the turn signal has not been correctly
installed and connected to the electrical supply on your motorbike. Do not
carry out the installation unless you are specifically trained to do so;
otherwise, please contact an authorized dealer Rizoma. Your guarantee does not
apply to damage due to wrong connection or excess voltage. Improper mechanical
installation or orientation of the turn signal may invalidate your motorbike’s
roadworthiness and insurance protection, or even lead to accidents. Check that
your turn signal are securely fitted before you ride your motorbike. Make sure
that your motorbike is standing firmly before you start work, as a fall may
lead to damage to the motorbike or injury to you or others.
ELECTRIC CONNECTIONS
Step 2
Disconnect the battery before starting to install the resistors. To avoid
damage to the electrical system of the bike, for electrical connection of turn
signal and resistor we recommend using the Rizoma electric wiring. Consult the
Rizoma catalog or the web site www.Rizoma.com to choose the correct electric
wiring. Arrange the wires to protect them from splash water and fasten them as
appropriate, such as with wire connectors. Reconnect the motorbike battery and
test the turn signal. Align the turn signal as described above. Install the
resistors in such a way that heat can escape effectively. These measures may
disable the rapid flashing function to alert the rider that one of the turn
signal is no longer working. Check your turn signal before each motorcycle
trip. These resistors will heat up if the turn signal is used for an extended
period. Make sure that other components or person are safe.
INSTALL ELECTRIC WIRING
Step 3
Warnings
RIZOMA reserves the right, in its sole discretion, to make changes to the
product and this information at any time and without prior notice. Although
many catalogs and advertisements depict riders engaged in extreme or stunt
riding, this activity is extremely dangerous, increases the risk of an
accident, and increases the severity of any injury. The action depicted is
performed by professionals under strictly controlled riding conditions.
Only you know the limits of your riding ability and only you can control the
conditions under which you ride. By and in consideration for his/her purchase
and use of the RIZOMA product, the user expressly recognizes and agrees that
in the event of any claim arising out of the use of this RIZOMA product,
whether such claim is based in contract, warranty, tort (personal injury or
wrongful death) or otherwise, the laws of the Republic of Italy shall apply
and jurisdiction and venue for any such action shall be in the Courts of Busto
Arsizio, Italy.
All riders are strongly urged to take a motorcycle rider safety clinic. Always
wear a properly fitted and fastened motorcycle helmet (RIZOMA recommends a
full face helmet), that has been approved by ANSI , SNELL, CE, or any other
relevant authority, and any other safety equipment necessary for your riding
style, such as full finger gloves, boots, and body armor.
Be sure to read and follow all the instructions and warnings that originally
accompanied your motorcycle, as well as the literature that accompanied any
other component parts installed on your motorcycle.
Be sure that your tires are inflated to the correct pressure and that there is
no damage whatsoever in the tread or sidewall of the tire.
Legal notes
Some of our products may not be approved for road circulation in the
countries where homologation is required. Thus RIZOMA® srl declines any
responsibility for a different use of its products.
Rev.: 00
Documents / Resources
|
rizoma MI EE146 00 Wiring Kit for Front Turn
Signals
[pdf] User Manual
MI EE146 00 Wiring Kit for Front Turn Signals, MI EE146 00, Wiring Kit for
Front Turn Signals, Wiring Kit
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>