superun CT05 Treadmill for Home User Manual

superun CT05 Treadmill for Home User Manual

**INSTALLATION INSTRUCTIONS

**

Welcome to use Help you enjoy exercising at home
Specification
Specifications：CT04
Product Size：55.5285.2inches
Product weight：68.3LBS
Peak horsepower：3.0HP
Running belt size：42.3*16.5inches
Rated voltage：120V
Maximum load：300LBS
Maximum speed：7.5MPH

SAFETY PRECAUTIONS

Please read all instructions carefully before operating this product.
Basic precautions should always be followed when using the device, including the following safety instructions:

• Please do not use the machine when you are sick, tired or drunk.
• Please wear comfortable clothes and avoid flip-flops or skirts when using this machine.
• Please start from suitable sport as excessive exercise may affect health.
• Load capacity 300LBS, overload may cause damage.
• Please ensure that all parts are not damaged and fixed before use. The device should be placed on a flat surface when used.
• Do not attempt any maintenance or adjustments other than those described in this manual.
• The device is for home use only. Do not use the device in a commercial, rental, or institutional environment.
• Only one person is allowed to use the device.
• Keep children and pets away from the device when using it.
• If you experience any chest pain, nausea, dizziness, or shortness of breath, stop exercising immediately and consult your doctor before continuing.

WARM-UP

Sports suggestions and guidelines
WARNING!  Before beginning this or any exercise program, you should consult your physician.
Warming up prepares the body for the exercise by increasing circulation, supplying more oxygen to the muscles and raising body temperature.
Begin each workout with 5 to 10 minutes of stretching and light exercise to warm up.The photos on this page show several forms of basic stretching you may perform before your workouts. In order to achieve an adequate warm-up, perform each stretch three times.

1. Stretch down:
   Bend your knees slightly with your body stretch down slowly, let your back and shoulders relax, and try to extend your hands to touch your toes. Hold for 10-15 seconds and take a break for a few seconds. Repeat 3 times.

2. Hamstring stretch:
   Sit down on a clean cushion, straighten one leg and place the other leg inward towards the thigh and snug on the inside of the straightened leg. In the meantime, try to touch the toes of your straitened leg with the hand at the same side. Hold for 10-15 seconds and take a break for a few seconds.
   Repeat 3 times for each leg.

3. Calf and Achilles Tendon Stretches:
   Place both hands against the wall while standing with one foot behind the other, keeping your back leg straight and both heels planted on the ground while leaning against the wall. Hold for 10-15 seconds and take a break for a few seconds. Repeat 3 times for each leg.

4. Quadriceps Stretch:
   Hold your body steady with your left hand holding against the wall and right hand reaching back to grab your right heel and pull it slowly towards your hips, until you feel the muscle tightness at the front side of your thigh. Hold for 10-15 seconds and take a break for a few seconds. Repeat several times for each leg.

5. Sartorius (muscle of inner thigh) Stretch:
   Sit on the floor with your two feet holding against each other and your knees pointing to the opposite directions, grab your feet with your hands and pull them toward your groin. Hold for 10-15 seconds and take a break for a few seconds. Repeat 3 times.

PRODUCTS AND ACCESSORIES

Product introduction

PRODUCTS AND ACCESSORIES

USING THE TREADMILL

FUNCTION DIAGRAM

When the machine is running, the display window automatically switches every 5 seconds. The indicator light at the bottom of the luli window changes with the display of the window. The information displayed in different Windows is as follows:

1. “Speed” window
   The current speed value is displayed in the running state, and the speed is on. The display range is 1-7.5mph.
   （1）When the column pillar is open, the maximum speed is 7.5mph
   （2）When the column pillar is closed, the maximum speed is 3.8 mph

2. “Time” window
   Display exercise time. The time range is 0:00-99:59 minutes,Maximum display 18h.

3. “Distance” window
   Display the moving distance, the display range is 0.00-9999mp miles, the reverse count is decremented from the set value to zero, when the counter turns to 0, the machine will steadily descend to stop.

4. Calories window”
   Display the calorie consumption value, the display range is 0.0-9999 kcal.
   The reverse count is decremented from the set value to zero, when the counter turns to 0, the machine will steadily descend to stop.

Remote control

1. Press the “Speed -” key to reduce the machine speed.
2. Press “Speed +” to increase the speed of the machine.
3. Press the “ON/OFF” button, and the machine will start or stop slowly.
   1. In the standby state, directly press the “ON/OFF” button, the treadmill would start to move at the speed of 0.2 miles/hr, other windows start counting up from 0, press “+”,”-” button to change the speed.

Unmanned Shutdown:
In the operating state of the treadmill, if the treadmill detects an unmanned state for more than 10s, it will automaticallystop.
5. Treadmill supports connection to mobile phone via Bluetooth

1. Download PitPat app on your phone and install it Search for “PitPat”in the app store or scan the following QR code to download and install the app.
2. Configure PitPat app account Open PitPatt app and follow the app instructions to log in or register account information
3. Connect the treadmill
   (1) Turn on the Bluetooth function of the mobile phone (the android mobile phone also needs to turn on the positioning function)
   (2) Open the PitPat app (if the app prompts for authorization, please grant the app related permissions)
   (3) Enter the app home page, click the treadmill icon in the upper left corner of the home page to enter the search interface,
   your phone will automatically search for nearby devices. Tap your treadmill (devices starting with PitPat-T are your treadmills) to connect.
   After the treadmill makes a beep, the connection is successful, and the Bluetooth icon on the treadmill panel lights up.
   Note: Please make sure your phone is connected to the Internet when connecting the treadmill via Bluetooth
   Please refer to the APP description for detailed networking configuration

Note：If  the treadmill is not connected to the mobile app, the Bluetooth icon of the treadmill is off; if the treadmill is successfully connected to the mobile app, the Bluetooth icon of the treadmill is on
Sleep function description:
Treadmill WIFI network configuration
After the treadmill is successfully connected to the mobile app, it will enter the treadmill WIFI configuration interface.
Note:  The treadmill only supports 2.4GHZ WIFI (the app also only displays the 2.4GHZ WIFI signal that the treadmill can search for), please make sure that your network device can provide 2.4GHZ WIFI signal
(1) Find the network you need to connect to
(2) Enter your WIFI password according to the prompt. After the treadmill successfully connects to the network, the WIFI icon on the treadmill  panel lights up and the app will return to the home page.
Note:  If the WIFI connection fails, after the WIFI returns to normal, please restart the treadmill so that it can reconnect to the Internet
5.Connect the bracelet to the treadmill
Turn on the treadmill, put the screen of the bracelet on the NFC logo of the treadmill, the treadmill make a sound of “bleep”, and the bracelet is connected with the treadmill.
Once the bracelet is successfully bound, it will recording your running information immediately.
When the treadmill stops running and there is no operation for more than 4 minutes, it will enter the sleep state. The electronic watch will automatically turn off the display. Press any key to wake up the electronic watch, and then enter the initial standby state again after full display.

 INSTALLATION STEPS

Installation steps

INSTALLATION INSTRUCTIONS

1. First, adjust the foot pads, and place them on flat ground and make sure there is a space of 50cm in front and rear.

2. Connect the power supply，turn on the switch.
   

3. First check and install the battery,press the “ON/OFF”button, there would be 3 seconds delay displayed on thepanel before operating.

4. Start using a walking treamill.
   

MAINTENANCE INSTRUCTION

Slip and correction of walking belt

1. Clean the treadmill
   Turn off the machine and unplug the power cord Apply a mild cleaner to a cotton cloth.
   Do not spray the cleaner directly on the walking belt Do not wipe under the walking belt

2. Walking belt lubrication
   Turn off the walking machine and unplug the power cord Lift the edge of the walking belt and smear the inner surface with silicone oil Start the walking treadmill and run at 3mph for 10-20 seconds before use The walking belt should be lubricated every one month

3.  When running belt leans to the left, adjusting screw on the left 1-2 turns clockwise. Then, test running; If the running belt still leans to the left, repeat the above steps until the running belt is aligned.

4. When running belt leans to the right, adjusting screw on the right 1-2 turns clockwise. Then, test running; If the running belt still leans to the right,repeat the above steps until the running belt is aligned.

5. When the running belt gets too tight it will cause stronger resistance. Please adjust both sides screws 1-2 turns counterclockwise, loosen the belt until stopping skidding or pausing; When the running belt too loose, please adjust both sides screws 1-2 turns along the clockwise.

COMMON FAULTS AND HANDLING METHODS

Er1: indicates that the electronic meter and electronic control communication abnormal phenomenon prompt

Erl solutions to common problems| The communication line of the electronic meter is not connected, broken, poor contact| Please reconnect the communication line
---|---|---
No signal output of electronic meter| Replace the electronic meter, to be repaired
No signal output of the lower control| Replace the lower control, to be repaired

Er3: indicates that the lower control detects the motor over-voltage protection information prompt

Er3 solutions to common problems| Walker load exceeds the rated working voltage of the motor| Recommended to use within the rated working voltage of the motor
---|---|---
Walking machine motor abnormal / due to light sensor failure caused by speed too fast| Replace the motor / replace the photoelectric sensor
Lower control board over-voltage detection circuit failure| Replace the lower control, pending repair

Er4: indicates that the lower control detects the motor overcurrent protection information prompt

Er4 solution to common problems| The load of the walker exceeds the rated working current of the motor| Recommended to be within the rated operating current of the motor
---|---|---
Walking machine and motor assembly structure problems,resulting in motor resistance or blocking phenomenon| Check the walking machine structure is normal
Lower control current limiting system failure| Replace the lower control, pending repair

Er5: indicates that the lower control detects the motor overload abnormal phenomenon prompt

Er5 common problem solution| The current is too high during the continuous time| Please check whether the power supply line is normal
---|---|---
Lower control board detection line failure| Replace the lower control, pending maintenance

Er6：Indicates that the lower control detects the abnormal phenomenon of speed

Er6 solutions to common problems| Motor line is not connected properly| Reassemble
---|---|---
The lower control board detection line failure or motor damage (no sense mode)| Replace the lower control or motor, pending repair

Er7: The controller does not receive signal

Er7 or – common problem solution| The communication line of the electronic meter is not connected, broken, poor contact| Please reconnect the communication line
---|---|---
Lower control board detection line failure| Replace the lower control, pending repair

Er99: Unmanned Shutdown

Er 99| In the operating state of the treadmill, if the treadmill detects an unmanned state for more than 10s, it will automatically stop.
---|---

FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1.  This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.
   RF Exposure Information
   This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>