superun BA03 V2.6 Treadmill For Home Instruction Manual

superun BA03 V2.6 Treadmill For Home

SPECIFICATION

Welcome to use Help you enjoy exercising at home

• Product Size: 49.1
• Product weight: 45.85LBS
• Peak horsepower: 2.5HP
• Running belt size: 39.4*15.7inch
• Rated voltage: 120V
• Maximum load: 300LBS
• Maximum speed: 3.8MPH

SAFETY PRECAUTIONS

Please read all instructions carefully before operating this product. Basic precautions should always be followed when using the device, including the following safety instructions:

• please do not use the machine when you are sick, tired or drunk.
• Please wear comfortable clothes and avoid flip-flops or skirts when using this machine.
• Please start with a suitable sport as excessive exercise may affect health.
• Load capacity 300LBS, overload may cause damage.
• please ensure that all parts are not damaged and fixed before use. The device should be placed on a flat surface when used.
• Do not attempt any maintenance or adjustments other than those described in this manual.
• The device is for home use only. Do not use the device in a commercial, rental, or institutional environment.
• Only one person is allowed to use the device.
• Keep children and pets away from the device when using it.
• If you experience any chest pain, nausea, dizziness, or shortness Of breath, stop exercising immediately and consult your doctor before continuing.

WARM-UP

Sports suggestions and guidelines

• WARNING! Before beginning this or any exercise program, you should consult your physician.
• Warming up prepares the body for exercise by increasing circulation, supplying more oxygen to the muscles, and raising body temperature.
• Begin each workout with 5 to 10 minutes of stretching and light exercise to warm up. The photos on this page show several forms of basic stretching you may perform before your workouts. To achieve an adequate warm-up, perform each stretch three times.

1. Stretch down:
   • Bend your knees slightly with your body stretched down slowly, let your back and shoulders relax, and try to extend your hands to touch your toes. Hold for 10-15 seconds and take a break for a few seconds. Repeat 3 times.
2. Hamstring stretch:
   • Sit down on a clean cushion, straighten one leg place the other leg inward towards the thigh, and snug on the inside of the straightened leg.
   • In the meantime, try to touch the toes of your straitened le with the hand on the same side. Hold for 10-15 seconds and take a break for a few seconds. Repeat times for each leg.
3. CaIf and Achilles Tendon Stretches:
   • Place both hands against the wall while standing with one foot behind the other, keeping your back leg straight and both heels planted on the ground while leaning against the wall.
   • Hold for 10-15 seconds and take a break for a few seconds. Repeat 3 times for each leg.
4. 0uadriceps Stretch:
   • Hold your body steady with your left hand holding against the wall and your right hand reaching back to grab your right heel and pull it slowly towards your hips, until you feel the muscle tightness at the front side ot your thigh.
   • Hold for 10-15 seconds and take a break for a few seconds. Repeat several times for each leg.
5. Sartorius (muscle of innerthi2h) Stretch:
   • Sit on the floor with your two feet holding against each other and your knees pointing to the opposite directions, grab your feet with your hands and pull them toward your groin.
   • Hold for 10-15 seconds and take a break for a few seconds. Repeat 3 times.

PRODUCTS AND ACCESSORIES

Product introduction

FUNCTION DIAGRAM

The function of the display panel is described

When the machine is running, the display window automatically switches every 5 seconds. The indicator light at the bottom Of the luli window changes with the display of the window. The information displayed in different Windows is as follows:

1. “WIFI” window
   • Display the WIFI indication. The icon will light up when the WIFI connection is successful.
2. “Bluetooth” window
   • Display the Bluetooth indication. The icon will light up when the Bluetooth connection is successful.
3. “Speed” window
   • The current speed value is displayed in the running state, and the speed is on. The display range is 0.6-3.8 mph.
   • ATTENTION: 0.6-3.8 MPH is the best walking speed, so our default value is 3.8 MPH
4. “Time” window
   • Display exercise time. The time range is minutes.
5. “Distance” window
   • Display the moving distance, the display range is 0.00-99.99 miles.
6. “Calories” window
   • Display the calorie consumption value, the display range is 0.0-9999 kcal.

• WIFI indicator
• Bluetooth indicator
• Speed Display
• Time Display
• Distance Display
• Calorie Display

Remote control

1. Press the “Speed -” key to reduce the machine speed.
2. Press “Speed +1′ to increase the speed of the machine.
3. Press the “ON/OFF” button, and the machine will start or stop slowly.
4. In the standby state, directly press the “ON/OFF” button, the treadmill would start to move at the speed of 0.6 miles/hr, other windows start countingup from 0, press +,-  button to change the speed.

USlNG THE TREADMILL

• Note: System requirements: ios13 or above ; android 6.0 or above.
• After registration, click the treadmill icon in the upper right corner

1. Waiting for the treadmill to connect
2. Searching for Wifi

Display “Green” to complete the connection

Treadmill supports connection to mobile phone via Bluetooth

1. Download Pitpat app on your phone and install it Search for “PitPat”in the app store or scan the following QR code to download and install the app.
2. Configure PitPat app account Open PitPat app and follow the app instructions to log in or register account information.
3. Connect the treadmill
4. Turn on the Bluetooth function of the mobile phone (the android mobile phone also needs to turn on the positioning function).
5. Open the PitPat app (if the app prompts for authorization, please grant the app related permissions).
6. Enter the app home page, click the treadmill icon in the upper left corner Of the home page to enter the search interface. your phone will automatically search for nearby devices. Tap your treadmill (devices starting with PitPat-T are your treadmills) to connect.
7. After the treadmill makes a beep, the connection is successful, and the Bluetooth icon on the treadmill panel lights up.
8. Note: Please make sure your phone is connected to the Internet when connecting the treadmill via Bluetooth.
9. Please refer to the APP description for detailed networking configuration.

Note: lf the treadmill is not connected to the mobile app, the Bluetooth icon of the treadmill is off; if the treadmill is successfully connected to the mobile app, the Bluetooth icon of the treadmill is on.
Treadmill WIFI network configuration
After the treadmill is successfully connected to the mobile app, it will enter the treadmill WIFI configuration interface.
Note: The treadmill only supports 2.4GHZ WI Fl (the app also only displays the 2.4GHZ WIFI signal that the treadmill can search for), please make sure that your network device can provide 2.4GHZ WIFI signal.

1. Find the network you need to connect to.
2. Enter your WIFI password according to the prompt. After the treadmill successfully connects to the network, the WIFI icon on the treadmill panel lights up and the app will return to the home page.
   • Note: If the WIFI connection fails, after the WIFI returns to normal, please restart the treadmill so that it can reconnect to the Internet.

FIRST USE GUIDANCE

1. Place the machine on a flat ground, keeping 50 cm Of space in front and back.
2. Adjust the mats to make the machine level and make each mat fall firmly on the ground.
3. Connect the power supply, and turn on the switch.
4. First, check the battery installation on the back Of the remote control, press the “ON/OFF” button, there will be 3 3-second delay displayed on the panel before operating.
5. Start using a walking treadmill.

MAINTENANCE INSTRUCTION

1. The treadmill must be lubricated after half a year or a cumulative run Of 100 hours.
2. Confirm the lubrication status. With the treadmill Off, lift the running belt from one side and reach for the surface under the running belt, if the lubricant can be touched, there is no need to add more lubricant. But if the lubricant dries up, refill it with it. (Use only non-petroleum-based lubricants).
3. Follow the figure below to properly add the lubricant.
4. Clean the treadmill.
5. Turn off the power, lift the running belt, and apply silicone Oil to the inner surface.
6. Start the treadmill and lubricate at 3 mph for 10-20 seconds.

• When the running belt leans to the left, adjusting the screw on the left 1-2 turns clockwise. Then, test running; If the running belt still leans to the left, repeat the above steps until the running belt is aligned.
• When the running belt leans to the right, adjust the screw on the right 1-2 turns clockwise. Then, test running; If the running belt still leans to the right, repeat the above steps until the running belt is aligned.
• When the running belt gets too tight it will cause stronger resistance. Please adjust both side’s screws 1-2 turns counterclockwise, and loosen the belt until stopping skidding or pausing; When the running belt is too loose, please adjust both side’s screws 1-2 turns along clockwise.

FAQS AND SOLUTIONS

Erl: Indicates that the communication between the electronic watch and the electronic control is abnormal

Er3: Indicates that the down-control motor overvoltage protection information prompts Er4: Indicates that the down-control motor over-current protection information prompt

Er5: Indicates that the lower control detects the abnormal phenomenon of motor overload

Er6: Indicates that the lower control detects the abnormal phenomenon of speed

Er7: Controller does not receive signal

Electric meter fault judgment and solution

FCC

FCC Warning
This device complies with part 15 Of the FCC Rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device Inust accepts any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used per the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

Support Service: +1888 318 4777

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>