SAFEGUARD SUPPLY LRA-D1000S Loud Doorbell Plugin Kit User Manual
- June 11, 2024
- SAFEGUARD SUPPLY
Table of Contents
LRA-D1000S Plug-In Strobe Kit
User Manual
(LRA-DCRXS+LRA-PBTXA)
PARTS & FUNCTION
LRA-DCRXS Plug-In Strobe Receiver LRA-PBTXA Wireless Push Button
THINGS TO KNOW PRIOR TO USE
- These instructions illustrate pairing a push button to the receiver. For other types of transmitters, follow the same process in step #5 in the “TRANSMITTER PAIRING & MELODY SELECTION”
- If your products are not automatically paired, please refer to the section below labeled “TRANSMITTER PAIRING & MELODY SELECTION”
SAFEGUARD SUPPLY CONTACT INFORMATION
Phone: 678-214-4212
email: [email protected]
2260 Moon Station Ct. NW #110
Kennesaw, GA 30144 USA
- Each LRA-DCRXS (receiver) can pair with a total of two wireless transmitters
- Once two (2) transmitters have been paired to a receiver, you cannot add an additional transmitter unless you delete a transmitter from the receiver
- There is no limit to the number of receivers you can pair with a transmitter
PRODUCT FEATURES
- Wireless range from transmitter to receiver is up to 1,000 ft.(line of sight)
- Each receiver can pair with a total of two (2) transmitters
- Receiver has three (3) operating modes; a) sound only, b) strobe only & c) sound & strobe
- Assign one (1) of eighteen (18) available melodies to each transmitter
- Strobe has two flashing patterns; a) slow & b) fast
- Operating frequency: 915MHz
- Operating temperature: 32F to 104F
- Product dimensions: 2.5” L x 1.2” W x 4.72” H
- Product weight: .25 lbs
LRA-PBTXA Push Button
Battery Installation
- Use the finger to unlock the lock lever
- Rotate the mounting bracket and bell press into 90 degree.
- Remove the mounting bracket from the unit.
- Rotate the Battery cover using a coin.
- Insert a CR2032 battery to battery compartment provided.
- Close the battery cover using a coin.
TRANSMITTER PAIRING & MELODY
If push button & receiver are purchased together as a kit (LRA-D1000S) then
the included push button is already paired to the included
receiver.
Step 1: Insert the included
battery into the transmitter (push button).
Step 2: Plug the receiver into a standard wall outlet.
Step 3: Press on hold the • Learn button for three seconds. A red LED
light will blink indicating the unit is in pairing mode. If the light is
solid, this means there are already two transmitters paired and you must clear
the transmitter memory from the receiver.
Step 4: Press the melody selector button to scroll through available
melodies. Once you hear a melody you prefer, do not press any button as the
melody is set for the transmitter (push button). Step 5: Once the melody
is selected, trigger the transmitter by pressing the push button. If you are
pairing a different type of transmitter, trigger that transmitter by following
the inst ructions provided for that transmitter.
Step 6: If successful, the receiver will generate a short tone. Press the
learn button again to exit the programming mode. The unit is now ready to use.
LRA-PBTXA MOUNTING OPTIONS Requires an electric drill for holes to fix the
wall bracket with the provided ram plug and screws. Stick the double-sided
adhesive on the mounting bracket.
Put the push button into the bracket
CHANGING THE MELODY
Press & hold the • learning button for 3 seconds to enter the pairing mode.
Press the melody selector button to select the melody desired. Once you hear
the melody you want for the transmitter, trigger the transmitter to lock in
that sound
CLEARING TRANSMITTER MEMORY FROM RECEIVER
The receiver can only pair with two (2) transmitters at a time. If you need to
replace a transmitter after two are already locked in, you must delete all
memory from the receiver by following the instructions below.
Press & hold the • learn button for 3 seconds to enter the pairing mode. Press
& hold the • learn button & melody selector button together for 3 seconds to
delete the memory.
The receiver will generate a beep tone to indicate all transmitr on the memory
is deleted. The red LED will change to blink. Now you can pair new transmitter
to the receiver.
Safety Instructions
Warning: To prevent fire or shock hazard. Do not expose this unit to rain
or moisture.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
The lighting flash with an arrowhead within a triangle alerts you to
uninsulated dangerous voltage within the product’s enclosure that could cause
an electric shock
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.
The exclamation point within a triangle alerts you to pressence of important
operating, maintenance and servicing instructions in this user’s manual.
FCC Statement:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which
the receiver is connected.
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: Modifications to this product will void the user’s authority to
operate this equipment.
