SAFEGUARD SUPPLY LRA Series LRA-EXTX Wired Doorbell Extender Owner’s Manual

SAFEGUARD SUPPLY LRA Series LRA-EXTX Wired Doorbell Extender Owner’s

Manual

Owner’s Manual
This device complies with Part 15 of the FCC rules, Operation of this device is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference, including interference that may cause undesired operation.

Introduction

The ERA-EXTX is a Transmitter compatible with the ERA-DCRX, ERA-VPRX, and the ERA- RXPG Receiver. The ERA-EXTX is a wireless transmitter that is wires to the terminal screws in a wired doorbell. When a visitor presses the push button (typically located next to the front door) the wired doorbell will ring as normal, and this transmitter will send a radio signal to a compatible receiver and play pre-selected melody.

Helpful Notes

• This product IS NOT a standalone product. It must be programmed to a compatible ERA receiver.
• The ERA-EXTX works with two wired doorbell push buttons, typically labeled as “front” and “back.” Each may be programmed to play a distinct melody on a compatible transmitter.
• The transmitter only works with standard wired doorbells that play a “ding-dong” and/or a “ding” sound. It is not supported with intercom or video-based doorbell systems.
• The transmitter is compatible with a 9V-18V AC wired door chimes.
• The transmitter is powered by a long lasting CR123A lithium battery (included).
• Unit measures 1.75” H x 2.00” W x 0.75” D.
• The wires are approximately 10” in length.
• Although transmitter installation is straight-foward, we recommend contacting a qualified electrician if you are not comfortable installing low-voltage products. ** Please ensure power to your wired doorbell is cut-off prior to installation.

Battery Installation

1. Open the front cover by insert a small flat-head screw driver. (figure 1) into the small notch on the cover & gently pushing in.
2. Remove top half of case from lower case.
3. Install the included CR123A battery in the holder.
4. Test the battery by pressing the “front” or “back” button. The red LED located in the center of the unit should light.

Note: Program the transmitter to the compatible receive prior to wiring the transmitter & replacing the cover.

Pair Transmitter to Receiver

Always test the transmitters programming prior to wiring & mounting the receiver.
The transmitter works with all ERA receivers. Basic programming calls for the user to pair the transmitters with a receiver & select a melody for the transmitter to instruct the receiver to play when triggered. In the example below, the transmitter will be programmed to the ERA-DCRX.
If you are using a different ERA receiver, follow the programming instructions for that receiver to put the receiver in programming mode and to change the melody.
For quick setup, however, each zone defaults to a basic “ding-dong” sound allowing you to easily pair the transmitter for a faster set up process.

1. On the ERA-DCRX receiver, hold down the “mode” (left button in figure 2 below) button until you hear a short tone sound & the “zone 1” LED flashes for approximately 3 second. (See figure 2 below.)
2. If you are programming the transmitter to zone 1press the “front” button on the transmitter (see figure 3). You will hear the receiver play a short musical note (zone 1 will flash). If you are not programming a second wired button, skip to step 5.
3. To program the “back” button to a different zone, press the “zone” button on the receiver to scroll to the appropriate zone . The zone you want to program will flash. Repeat step 2 above, pushing the “back” button (figure 3.)
4. Once you have programmed all the zones move to the next step.
5. To exit program mode, hold down the “mode” button until you hear a short tone sound (approx 3 sec)

1. Hold down the “zone” button until you hear a short tone & all LEDs on front panel of receiver are red (approx 3 seconds). The zone you are programming will flash.
2. Press the “volume” button to scroll through the 12 available melodies for selection. Once you find a melody you like, move to step 3.
3. Press the “zone” button to scroll to the next zone & repeat step 2 to program a melody to other zones.
4. Once you have programmed a melody to all necessary zones, move to step 5.
5. Hold down the “zone” button until you hear a short tone sound (approx 3 seconds) notifying the receiver is out of melody programming mode.

Test the Programming of Transmitter to Receiver

• Push the “front” button and/or the “back” button on the transmitter.
• After completing the programming steps above, test the programming pairing prior to mounting the transmitter. You should see a red LED on the transmitter, & the receiver should play the selected melody (make sure volume is on).
• If there’s no red LED on the transmitter, ensure the plastic wrapper is removed from the battery & it is inserted correctly.

How to Wire the Transmitter to Your Wired Doorbell

If you are not familiar with electrical projects, please hire a certified electrician. Ensure you have no power going to your wired doorbell by turning off the circuit breaker.

1. Remove the cabinet cover from your wired doorbell. This is typically located in the foyer or front hallway of you home.
2. Notice the 3-terminal screws on the wired doorbell mechanism (see figure 4).
3. Connect the red wire from the transmitter to the front door terminal screw located on your wired doorbell (see figure # above).
4. Connect the white from the transmitter to the “back” or “second” door terminal screw on your wired doorbell. If you are not using the second door you can still connect the screw or simply wrap the wire connector in electrical tape to prevent interference.
5. Connect the black wire from the transmitter to the “trans” or “common” terminal screw on your wired doorbell
6. Before mounting the transmitter, test the unit by pressing the wired doorbell push button (usually located outside your home next to the front door). This should trigger the corresponding zone on the ERA receiver (typically zone 1).
7. If you have a second wired doorbell button & have programmed it using these instructions, push the button. Zone 2 on the receiver should trigger.
8. When testing the “front” & “back” button, your wired doorbell should chime as normal. The ERA receiver should play the selected melody that correspond to the zone settings you have programmed.

Mounting the Transmitter

It doesn’t matter where you mount the the ERA-EXTX transmitter. In most cases, simply placing it on top of the wired door chime cabinet keeps it out of site for most visitors to your home.

• Use the supplied double-sided tape to stick the transmitter above, to the side, or below the wired doorbell mounted on the wall.
• In some cases, there may be enough room inside your wired doorbell cabinet to put the ERA-EXTX inside it.
• As mentioned before, you can also simply sit the transmitter on top of the wired doorbell cabinet.

Programming with Other Transmitters
The ERA-EXTX is compatible with the ERA-VPRX Portable Receiver & the ERARXPG Plugin Receiver. The programming of the ERA-EXTX is very similar for these receivers. The only change is how to put the respective receiver into programming mode, choosing a melody, & changing the zone. Please consult the manual for the specific receiver when programming.

TECHNICAL SUPPORT

If you encounter any difficulty in the operation of this product after reading the manual, please contact us. You can reach us by phone at 904-245-1184 from 8:00 AM to 5:00 PM Monday through Friday (Eastern Standard Time). We will be happy to answer your questions and help you in any way we can.

WARRANTY
Safeguard Supply warrants this product to be free of defects in material and workmanship for a period of one year from the date of purchase. This warranty does not cover damage resulting from accident, abuse, act of God or improper operation. If this product does become defective, simply return it to Safeguard Supply. Please include a note describing the troubles along with your name and return address as well as the original sales receipt. If the product is covered under warranty it will be repaired or replaced at no charge. If it is not covered by warranty, you will be notified of any charges before work is done.

Safeguard Supply, 2260 Moon Station Ct. NW #110, Kennesaw, GA 30144 Phone: 678-214-4212, www.safeguardsupply.com

Legal Notices

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help important announcement

Warning: Cancer and Reproductive Harm. Go to www.P65Warnings.ca.gov for more information.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>