SPINRITE 3.25hp Variable Speed Router Motor Instruction Manual

September 11, 2024
SPINRITE

3.25hp Variable Speed Router Motor

“`html

Specifications

  • Horsepower: 3.25hp
  • No Load RPM: 10,000-22,000
  • Volts AC: 120

Product Usage Instructions

General Safety Rules

  1. Keep work area clean and well-lit. Cluttered, dark work areas
    invite accidents.

  2. Avoid dangerous environments. Do not use your power tool in
    rain, damp or wet locations or in the presence of explosive
    atmospheres (gaseous fumes, dust or flammable materials). Remove
    materials or debris that may be ignited by sparks.

  3. Keep children and bystanders away. Children and bystanders
    should be kept at a safe distance from the work area to avoid
    distracting the operator and contacting the tool or extension
    cord.

  4. Protect others in the work area from debris such as chips and
    sparks. Provide barriers or shields as needed.

  5. Make workshop childproof with padlocks, master switches, or by
    removing starter keys.

  6. Double insulated tools are equipped with a polarized plug (one
    blade is wider than the other). This plug will fit in a polarized
    outlet only one way. If the plug does not fit fully in the outlet,
    reverse the plug. If it still does not fit, contact a qualified
    electrician to install a polarized outlet. Do not change the plug
    in any way. Double insulation eliminates the need for the
    three-wire grounded power cord and grounded power supply
    system.

  7. Warning: To reduce the risk of injury, always
    unplug tool before attaching, removing accessories.

  8. Grounded tools must be plugged into an outlet properly
    installed and grounded in accordance with all codes and ordinances.
    Never remove the grounding prong or modify the plug in any way. Do
    not use any adapter plugs. Check with a qualified electrician if
    you are in doubt as to whether the outlet is properly
    grounded.

  9. Warning: To reduce the risk of injury, always
    unplug tool before attaching, removing accessories.

  10. Guard against electric shock. Prevent body contact with
    grounded surfaces such as pipes, radiators, ranges, and
    refrigerators. When making blind or plunge cuts, always check the
    work area for hidden wires or pipes. Hold your tool by insulated
    non-metal grasping surfaces. Use a Ground Fault Circuit Interrupter
    (GFCI) to reduce shock hazards.

FAQ

Q: What should I do if I encounter issues with the motor?

A: If you experience any problems with the motor, please contact
us at 800-752-0725 for assistance during our office hours from 9:00
a.m. to 4:00 p.m. EST, Monday – Friday.

Q: How do I adjust the variable speed on the router motor?

A: To adjust the variable speed on the router motor, use the
Variable Speed Dial provided in the package. Turn the dial to set
your desired speed within the range of 10,000-22,000 RPM.

“`

S P IN R IT E R O U T E R M O T O R
ROUTER MOTOR
3.25hp VARIABLE SPEED

D IA G R A M (Q TY) PA RT N AM E NUMBER
1 (1) Router M otor 2 (1) Power Cord 14AW G 3 (1) Variable Speed Dial 4 (1) Power Switch 5 (1) Collet Shaft 6 (1) 1/4″ Collet 7 (1) 1/2″ Collet 8 (1) Collet Nut 9 (2) W rench

C A U T IO N ! Read all instructions carefully. SAVE THESE INSTRUCTIONS. Refer to them often and use them to instruct others.

Volts AC 120

S P E C IF IC A T IO N S

H o rs e p ow e r

No Load RPM

3.25hp* 10,000-22,000

If you think you’re m issing anything, call us at 8 0 0 -7 5 2 -0 7 2 5 from 9:00 a.m . to 4:00 p.m . EST M onday – Friday.

GENERAL SAFETY RULES
W A R N IN G ! READ AND UNDERSTAND ALL INSTRUCTIONS Failure to follow all instructions listed below, m ay result in electric shock, fire and/or serious personal injury.

C A U T IO N ! Read all instructions carefully. SAVE THESE INSTRUCTIONS. Refer to them often and use them to instruct others.

· WORK AREA

1. K e e p w o rk a re a c le a n a n d w e ll lit. C luttered, dark w ork areas invite accidents.

2. A vo id d a n g e ro u s e n v iro n m e n ts . D o not use your pow er tool in rain, dam p or w et locations or in the presence of explosive atm ospheres (gaseous fum es, dust or flam m able m aterials). R em ove m aterials or debris that m ay be ignited by sparks.

3. K e e p c h ild re n a n d b y s ta n d e rs a w a y . C hildren and bystanders should be kept at a safe distance from the w ork area to avoid distracting the operator and contacting the tool or extension cord.

4. P ro te c t o th e rs in th e w o rk a re a from debris such as chips and sparks. P rovide barriers or shields as needed.

5. M a k e w o rk s h o p c h ild p ro o f w ith padlocks, m aster sw itches, or by rem oving starter keys.

· E LE C TR IC A L S A FE TY

6. D o u b le in s u la te d to o ls a re e q u ip p e d w ith a p o la riz e d p lu g (one blade is w ider than the other). This plug w ill fit in a

polarized outlet only one w ay. If the plug does not fit fully in the outlet, reverse

the plug. If it still does not fit, contact a qualified electrician to install a

polarized outlet. D o not change the plug in any way. D ouble insulation elim inates the need for the three-w ire grounded pow er cord and grounded pow er supply system .

W A R N IN G ! To reduce the risk of injury, always unplug tool before attaching, removing accessories

7. G rounded tools m ust be plugged into an outlet properly in s ta lle d a n d g ro u n d e d in accordance w ith all codes and ordinances. N ever rem ove the grounding prong or m odify the plug in any w ay. Do not use any adapter plugs. C heck w ith a qualified electrician if you are in doubt as to w hether the outlet is properly grounded. If the tool should electrically

or m aking adjustm ents. Use only specifically recom m ended accessories. O thers m ay be hazardous. Never disassem ble the tool or try to do any rewiring on the tool’s electrical system.

m alfunction or break down, grounding provides a low resistance path to

carry electricity away from the user.

8. G u a rd a g a in s t e le c tric s h o c k . Prevent body contact w ith grounded surfaces such as pipes, radiators, ranges and refrigerators. W hen m aking blind or plunge cuts, alw ays check the w ork area for hidden w ires or pipes. H old your tool by insulated nonm etal grasping surfaces. Use a G round Fault C ircuit Interrupter (GFCI) to reduce shock hazards.

9. D o n ot expo se to rain o r u se in d a m p lo catio ns.

10. D o n o t a b u s e th e c o rd . N ever use the cord to carry the tools or pull the plug from an outlet. Keep cord aw ay from heat, oil, sharp edges or m oving parts. Replace dam aged cords im m ediately. D am aged cords increase the risk of electric shock.

· PERSONAL SAFETY

11. K n o w y o u r p o w e r to o l. R ead this m anual carefully to learn your pow er tool’s applications and lim itations as w ell as potential hazards associated w ith this type of tool.

12. S ta y a le rt, w a tc h w h a t y o u a re d o in g , a n d u s e c o m m o n s e n s e w hen operating a pow er tool. D o not use tool w hile tired or under the influence of drugs, alcohol, or m edication. A m om ent of inattention w hile operating pow er tools m ay result in serious personal injury.

13. D res s p ro p e rly . D o not w ear loose clothing or jewelry. W ear a protective hair covering to contain long hair. These m ay be caught in m oving parts. W hen w orking outdoors, w ear rubber gloves and insulated non-skid footwear. Keep hands and gloves away from m oving parts.

14. R e d u c e th e risk o f u n in te n tio n a l s tartin g . Be sure your tool is turned off before plugging it in. Do not use a tool if the pow er sw itch does not turn the tool on and off. Do not carry a plugged-in tool w ith your finger on the switch.

15. R e m o v e a ll a d ju s tin g k e y s a n d w re n c h e s . M ake a habit of checking that adjusting keys, w renches, etc. are rem oved from the tool before turning it on.

16. D o n o t o v e rre a c h . M aintain control. Keep proper footing and balance at all tim es.

17. U s e s a fe ty e q u ip m e n t. Everyone in the w ork area should w ear safety goggles or glasses w ith side shields com plying w ith current safety standards. Everyday eyeglasses only have im pact resistant lenses. They are not safety glasses. W ear hearing protection during use and a dust m ask. H ard hats, face shields, safety shoes, etc. should be used w hen specified or necessary. Keep a fire extinguisher nearby.

18. K eep guards in p lace and in w o rkin g order.

19. N e v e r s ta n d o n to o l. Serious injury could occur if the tool is tipped or if the cutting tool is tipped or if the cutting tool is unintentionally contacted.

20. K eep hands aw ay from all cutting edges and m oving parts.

C A U T IO N ! Before each start, check that Router M otor is securely in place. Check that the w ork is rigidly clam ped and secure before m aking any cuts.

· TOOL USE & CARE

21. S e c u re w o rk . Use clam ps or a vise to hold w ork w hen practical. It is safer than using your hand and it frees both hands to operate the tool.

22. D o n o t fo rc e to o l. Your tool w ill perform best at the rate for w hich it w as designed. Excessive force only causes operator fatigue, increased w ear and reduced control.

23. U s e th e rig h t to o l. Do not use a tool or attachm ent to do a job for w hich it is not recom m ended.

24. U n p lu g to o l w hen it is not in use before changing accessories or perform ing recom m ended m aintenance.

25. S to re id le to o ls . W hen not in use, store your tool in a dry, secured place. Keep out of reach of children.

26. N e v e r le a v e th e to o l ru n n in g u n a tte n d e d . Turn pow er off. D o not leave the tool until it com es to a com plete stop.

27. C h e c k fo r d a m a g e d p a rts . Inspect guards and other parts before use. C heck for m isalignm ent, binding of m oving parts, im proper m ounting, broken parts and any other conditions that m ay affect operation. If abnorm al noise or vibration occurs, turn the tool off im m ediately and have the problem corrected before further use. D o not use a dam aged tool.

28. U se p ro p e r a c c e s s o rie s . C onsult this m anual for recom m ended accessories. U sing im proper accessories m ay be hazardous. Be sure accessories are properly installed and m aintained. Do not discard a guard or other safety device w hen installing an accessory or attachm ent.

29. M a in ta in to o ls c a re fu lly . Keep cutting edges sharp and clean. Follow instructions for lubricating and changing accessories. Periodically inspect tool cords and extension cords for dam age. H ave dam aged parts repaired or replaced by the m anufacturer.

30. M a in ta in la b e ls & n a m e p la te s . These carry im portant inform ation.

· S ER VIC E

31. S ervice p erfo rm ed by unqualified personnel m ay resu lt in a risk o f injury and m ay void w arranty.

· A D D ITIO N A L W A R N IN G S

32. W A R N IN G ! Som e dust created by pow er sanding, saw ing, grinding, drilling and other construction activities contains chem icals know n by the State of C alifornia to cause cancer, birth defects or other reproductive harm .

S om e exam ples of these chem icals are: lead from lead-based paint, crystalline silica from bricks and cem ent and other m asonry products, arsenic and chrom ium from chem ically-treated lum ber.

Your risk from these exposures varies, depending on how often you do this type of w ork. To reduce your exposure to these chem icals: w ork in a w ell- ventilated area, and w ork w ith approved safety equipm ent, such as those dust m asks that are specifically designed to filter out m icroscopic particles.

33. R ead, understand, and fo llow th e instructions packaged w ith th e router tab le and router lift.

34. A lw ays w e a r safety g o g gles and d u st m ask. Use only in a w ell- ventilated area. U sing personal safety devices in a safe environm ent can reduce the risk for injury.

W A R N IN G ! To reduce the risk of injury, wear safety goggles or glasses with side shields, ear protection & a dust mask.

35. S om e w oods contain preservatives th at can

b e to x ic . Take extra care to prevent inhalation and skin contact w hen w orking w ith these m aterials. R equest, and follow, any

safety inform ation available from your m aterial supplier.

36. A lw a ys m a k e s u re th e w o rk p ie c e is fre e fro m n ails, s c rew s , a n d o th e r fo reig n o b je c ts . Keep the working edge away from the clam ping surface. Cutting these objects can cause loss of control of the w orkpiece and dam age to the bit.

37. N ever place hands near cutting surface.

38. N e v e r u s e d u ll o r d a m a g e d b its . Sharp bits m ust be handled w ith care. D am aged bits can break during use. Dull bits require m ore force, w hich could cause the bit to break. D am aged bits can throw carbide pieces and burn the w orkpiece.

39. W A R N IN G ! T o re d u c e th e ris k o f in ju ry alw ays unplug tool before attaching, rem oving accessories or m aking adjustm ents. U se only specifically recom m ended accessories. O thers m ay be hazardous.

40. A fter changing the bit or m aking any adjustm ents, m ake sure the collet nut and any other adjustm ent devices are securely tightened.

41. L o o s e a d ju s tm e n t d e v ic e s c a n u n e x p e c te d ly s h ift, c a u s in g lo s s o f c o n tro l. Loose rotating com ponents w ill be violently throw n. W atch for vibration or w obbling that could indicate an im properly installed bit.

42. A lw ays keep th e p o w er sup p ly co rd a w a y from m o vin g p arts on th e tool.
43. N ever start th e tool w h en th e bit is in co ntact w ith th e m a te ria l. The bit cutting edge m ay grab the m aterial causing loss of control of the w orkpiece.
44. N ever to uch th e b it d uring o r im m e d ia tely a fter use. After use the bit m ay be hot enough to burn bare skin.
45. T o re d u c e th e ris k o f in ju ry , a v o id ” c lim b c u ttin g .” C lim b cutting can cause the w orkpiece to be throw n violently out of your control. Even sm all router bits can result in clim b cutting. A lw ays feed the w orkpiece against the cutter rotation.

W A R N IN G ! To reduce the risk of injury, always use featherboards, push sticks or push blocks with
proper guarding. Keep hands aw ay from m oving bit. Refer to your Router Table m anual for proper table setup and use.

E X TE N S IO N C O R D S
Grounded tools require a three-wire extension cord. Double insulated tools can use either a two or three wire extension cord. As the distance from the supply outlet increases, you m ust use a heavier gauge extension cord. Using extension cords w ith inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool dam age. Refer to the table shown to determ ine the required m inim um wire size. The sm aller the gauge num ber of the wire, the greater the capacity of the cord. For example, a 14-gauge cord can carry a higher current than a 16-gauge cord. If you are using one extension cord for more than one tool, add the nam eplate am peres and use the sum to determ ine the required m inim um wire size.
· G uidelines for U sing E xtension C ords 1. If you are using an extension cord outdoors, be sure it is m arked with the suffix “W -A” (“W ” in Canada) to indicate that it is acceptable for outdoor use. 2. Be sure your extension cord is properly wired and in good electrical condition. Always replace a dam aged extension cord or have it repaired by a qualified person before using it. 3. Protect your extension cords from sharp objects, excessive heat and dam p or wet areas.
· R ecom m ended M inim um W ire G auge fo r E xtension C ords*

A M PS 25′-50′

15

16ga

5 0 ‘-1 0 0 ‘ 12ga

Extension Cord Length in Feet

100′-200′ 150′-300′ 200′-400’

10ga

8ga

6ga

2 5 0 ‘-5 0 0 ‘ 6ga

  • Based on limiting the line voltage drop to five volts at 150% of the rate amperes.

3 0 0 ‘-6 0 0 ‘ 4ga

I. A S S E M B LY
A . S electing th e B it The Router M otor can accom modate router bits with 1/4 or “1/2″ diam eter shanks. C A U T IO N ! Do not use router bits with a diam eter in excess of 3-1/2”.
B . C hanging C ollets
A Collet m ust be attached to the Collet Nut before it is put into the Collet Shaft. Be sure that the size of the Collet m atches the size of the bit shank being used. If the wrong size bit shank is used, the Collet m ay break.
For attaching or detaching the Collet Nut to the Collet, follow these instructions. FIGURE 1. 1. Always disconnect the Router M otor 1 from the power supply.
2. Loosen the Collet Nut 8 from the Collet Shaft 5 com pletely. 3. Snap the Collet 6 or 7 out of the Collet Nut.
4. Replace the Collet by snapping it back into the Collet. Tighten the Collet Nut assem bly onto the Collet Shaft.
W A R N IN G ! To reduce the risk of injury, always unplug tool before attaching, removing accessories
or m aking adjustm ents. Use only specifically recom m ended accessories. Others m ay be hazardous. Never disassem ble the tool or try to do any rewiring on the tool’s electrical system.

C . Installing th e B it Do not use this Router M otor unless it is securely installed into a recomm ended router lift and table.
To install the Router M otor into a router lift, read, understand, and follow the instructions packaged with the router lift.
It is not necessary to remove the Router M otor from the lift to
install a C ollet assem bly or a bit. (If removal of the Router Motor is desired, see the instructions packaged with the router lift.)

WA R N IN G ! TIoHreG duceFthE e rD isk oCf BA
injury, alw ays unplug tool before attaching, removing accessories
or m aking adjustm ents. Use only specifically recom m ended accessories. O thers m ay be hazardous. Never disassem ble the tool or try to do any rewiring on the tool’s electrical system.

1. Unplug the Router M otor from the power source.

2. Raise the Router M otor as high as possible. Always wipe wood chips, dust, or other foreign m aterials from the Collet Shaft and Collet assem bly before assem bling.

3. Assem ble the Collet assem bly onto the Collet Shaft.

4. Insert the bit shank into the Collet as far as it will go.

5. Back the bit shank out slightly to avoid bottom ing out. This equates to approxim ately 1/8″ (3.2mm ). Be sure there is a m inim um of 1/16″ between the top of the Collet assem bly and the radius to the cutting portion of the bit.

6. Be sure that the Collet is not clam ped to a fluted section on the bit shank. The Collet should be clam ped to a solid part on the bit shank.
7. Place one W rench 9 on flats on the Collet Shaft.

8. P lace the other W rench on the C ollet and tighten clockw ise. Tighten securely. FIGURE 2.

N O T E : N ever tigh ten a C ollet assem b ly w ith o ut inserting a bit sh an k o f th e proper size. This m ay dam age the C ollet.

D . R em o vin g th e B it Always wait for the bit to stop com pletely and unplug the Router M otor from the power supply before changing accessories or m aking adjustments. Never m ake adjustm ents while the Router M otor is running. Do not m odify or remove the guards.
To rem ove the bit, reverse the above procedure. After the Collet Nut initially b re a kfree it w ill m eet resistance again. Use the W renches and the Collet w ill release.

F. C onnection to the P ow er S ource · Before connecting the Router M otor to the power source m ake sure the Power Swtch 4 is in the “O ” off position. FIGURE 3. · Check that your power circuit has the sam e specifications as the Router Motor. · M ake sure the prongs on the Power Cord are straight and m ake good contact with the ou

II. FEA TU R ES O F TH E R O U TER M O TO R
A . S tarting / S topping the R outer M otor · Before starting the Router M otor always wipe wood chips, dust, or other foreign m aterials from the Collet Shaft and Collet and bit assembly. · The Router M otor has a Soft-Start feature. The Soft-Start feature reduces the amount of torque reaction of the tool. This feature gradually increases the m otor speed up from zero to the speed set by the Variable Speed Dial. · Always allow the Router M otor to com e to a com plete stop before m aking bit changes or adjustments.

B . E lectronic O verload P rotection Before the Router M otor is overloaded, the electronic overload protection circuit will turn off the Router M otor. If the Router M otor stops during use: 1. Turn the Power Switch to the “O” Off position. 2. Determ ine the cause of the overload (for example, dull bit, low voltage, excessive feed rate, etc.) and correct before continuing.
3. R estart the R outer M otor following Step II-A Starting / Stopping Rour tor instructions.

C . S peed C ontrol

· The Variable Speed Dial 3 on the face of the Router M otor allo to adjust the rotating speed (RPM) of the Router M otor from “H” High to “L” Low . FIGURE 4.

· Use the chart to determine the best speed for the bit diam eter. FIGURE 5.

· It is recom m ended that the speed be set prior to engaging the router bit into work. Should it be necessary to change the speed after work has begun, stop the Router Motor, remove the w ork piece from contact with the bit, adjust the speed, then resume the work.
D. Feedback C ontrol The Electronic Speed Control system allows the Router M otor to m aintain constant speed between no-load and load conditions.

FIG U R E 5

V a ria b le S peed Setting
Slow Slow M ed ium M ed ium M ed ium Fast Fast

RPM
10,000 12,000 14,000 16,000 18,000 20,000 22,000

M axim um Bit D iam eter
3″ to 3-1/2″ 3″ to 3-1/2″ 2-1/4″ to 2-1/2″ 2-1/4″ to 2-1/2″ 1-1/4″ to 2″ 1″ 1″

WA R N IN G ! To reduce the risk of injury, alw ays unplug tool before attaching, removing accessories
or m aking adjustm ents. Use only specifically recom m ended accessories. O thers m ay be hazardous. Never disassem ble the tool or try to do any rewiring on the tool’s electrical system.
W A R N IN G ! To reduce the risk of injury, always use featherboards, push sticks or push blocks with
proper guarding. Keep hands aw ay from m oving bit. Refer to your Router Table m anual for proper table setup and use.

IV . U S IN G T H E R O U TER M O TO R

C A U T IO N ! BIeH foreG eacF h sE tart,D ch eC ck thB a t A R outer M otor is securely in place. Check that the w ork is rigidly clam ped and secure before m aking any cuts.

W A R N IN G ! To reduce the risk of injury, w ear safety goggles or glasses with side shields, ear protection & a dust mask.

A . C utting
· Before using your router, consider the kind and total am ount of m aterial to be removed. It m ay be necessary, depending on the m aterial, to m ake m ore than one cut to avoid overloading the Router M otor. Keep the cutting pressure constant but do not crowd the router so the Router M otor speed slows excessively.
· Before beginning the cut on the actual workpiece, it is advisable to take a sam ple cut on a scrap piece of lum ber. This will show you exactly how the cut will look as well as enable you to check dimensions.
· The speed and depth of cut will depend largely on the type of m aterial being used. Keep the cutting pressure constant but do not use excessive force so the Router M otor speed slows excessively. It m ay be necessary on exceptionally hard woods or problem m aterials to m ake m ore than one pass to get the desired depth of cut..
· W hen m aking cuts on all 4 edges of the workpiece, it is advisable to have the first cut on the end of the workpiece across the grain of the wood. If chipping of the wood occurs at the end of a cut, it will be rem oved when m aking the next cut that is parallel w ith the grain.
· Position the fence so that the workpiece feeds against the cutter rotation. F e e din g th e w o rk p ie c e w ith th e cutter rotation is called clim b cutting, w hich is V ER Y D AN G ERO US. C lim b cutting can result in the w orkpiece being throw n violently out of your control at great speed.
W A R N IN G ! To reduce the risk of injury, avoid “clim b cutting.” Clim b cutting can cause the workpiece to be thrown violently out of your control. Even sm all router bits can cause dam age or injury if clim b cutting.

V. M A IN T E N A N C E
A . Tool M aintenance Keep your tool in functioning properly by adopting a regular m aintenance program . Before use, exam ine the general condition of your tool. Inspect guards, switches, power cords and extension cord for dam age. Check for loose screws, m isalignm ent, binding of m oving parts, im proper m ounting, broken parts and any other condition that m ay affect its safe operation. If abnorm al noise or vibration occurs, turn the tool off im m ediately and have the problem corrected before further use. Do not use a damaged tool.
W A R N IN G ! To reduce the risk of injury, electric shock and dam age to the tool, never im merse your tool in liquid or allow a liquid to flow inside the tool.
B . C leaning Y our Tool
Clean dust and debris from vents. Use only soft dam p cloth to clean your tool. Never use cleaning agents and solvents such as: gasoline, turpentine, lacquer thinner, paint thinner, chlorinated cleaning solvents, am m onia, household detergents containing am m onia, flam m able or com bustible solvents around tools. These are harm ful to your tool, plastics and insulated parts.
WA R N IN G ! To reduce the risk o f injury, always unplug tool before attaching, removing accessories
or m aking adjustm ents. Use only specifically recom m ended accessories. Others m ay be hazardous. Never disassemble the tool or try to do any rew iring on the tool’s electrical system .

S P IN R ITE
ROUTER MOTOR
O N E Y E A R L IM ITE D W A R R A N TY W arrantor warrants to the original purchaser that SpinRite Router M otor will be free from defects in m aterials and workm anship under norm al use and service for a period of one (1) year from the date of original purchase. The obligation of this W arranty is lim ited to repair or replacem ent, at our option, of com ponents which prove defective under norm al use. Any product or com ponent claimed to be defective should be sent during warranty period, postage prepaid to SpinRite W arranty Departm ent together with a copy of your original dated sales receipt. Please call for authorization num ber before sending. This warranty is in lieu of all other express warranties obligations or liabilities. ANY IMPLIED W ARRANTIES, OBLIGATIONS OR LIABILITIES, SHALL BE LIMITED IN DURATION TO THE ONE YEAR PERIOD OF THIS LIMITED W ARRANTY. NO AGENT, REPRESENTATIVE, DEALER, OR EMPLOYEE OF THE COMPANY HAS THE AUTHORITY TO INCREASE OR ALTER THE OBLIGATIONS OF THIS WARRANTY. This W arranty shall not apply to any product or com ponent which in the opinion of the W arrantor has been m odified or altered in any way, dam aged as a result of an accident, m isuse or abuse, or loss of parts. In no case shall the W arrantor be liable for any special or consequential dam ages, or any other costs or warranty, expressed or implied, whatsoever. This W arranty gives you specific legal rights, and you m ay also have other rights which vary from state to state.
If you think you’re m issing anything, call us at 800-752-0725 from 9:00 a.m . to 4:00 p.m . EST M onday – Friday.
S P IN R ITE
ROUTER MOTOR
© 2022 SpinRiteTM Brand WARNING! This product can expose you to chemicals, including chromium, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

REV050622

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals