BLAUPUNKT Honda and Toyota Plug and Play Tire Pressure Monitoring System User Manual

June 11, 2024
Blaupunkt

BLAUPUNKT-LOGO

Honda and Toyota Plug and Play Tire Pressure Monitoring System

BLAUPUNKT-Honda-and-Toyota-Plug-and-Play-Tire-PRODUCT-
IMAGE

Product Information

The product is a TPMS (Tire Pressure Monitoring System) that comes with internal and external sensors, a display, and a user manual. The system is designed to monitor the tire pressure of your vehicle and provide real-time alerts if the pressure drops below a certain threshold value. The system has two settings: Sensor Pairing and Threshold Value Setting.

Sensor Pairing Setting
To pair the sensors with the display unit, follow the below steps:

  1. Long press the Set button for 3 seconds.
  2. The display will show P1.
  3. Press OK button, and the FL tire will be waiting for a new ID.
  4. Once you install or reinstall FL external sensor, or inflate or deflate FL tire and keep it for at least 20 seconds, the screen will display a new ID number and give a success sound of DI, then it will turn to FR tire automatically.
  5. Note: Before leaving the factory, we have matched ID of sensor.

Threshold Value Setting|
To set the threshold value, follow the below steps:

  1. Long press the Set button.
  2. Click Set button 2 times again, screen display P3.
  3. Press OK button, then press the set button to switch between High Pressure Value & Low Pressure Value interface.
  4. Click OK, Value will flash, then click SET button to adjust the threshold Value Setting that you like.
  5. Click OK to make sure that the value is suitable for your tire.
  6. Press & hold the setting button to exit the setting interface.

Accessories

  • Internal sensor
  • External sensor
  • Display

Installation
For installation instructions, please refer to the user manual:

  • Page 2 – Internal sensor installation
  • Page 4 – External sensor installation

HONDA & TOYOTA PLUG & PLAY

Cautions Safety Notes
This TPMS(Tire Pressure Monitoring System)has been manufactured according to established safety guidelines. However, dangers may still occur if the safety notes in this manual is not observed. This manual is intended to familiarize the user with the TPMS’s important functions. Read this carefully, prior to using the appliance. Keep this manual in an easily accessible location. In addition, do observe the instructions of the devices used in conjunction with this appliance.

Disclaimer
In no event shall Company be liable for any direct, indirect, punitive, incidental, special consequential damages to property or life and whatsoever arising out of or connected with the use or misuse of our products

Structure & Functions

  1. Data Display
  2. Pressure Unit
  3. Display Battery Status
  4. OK Button
  5. Setting Button
  6. TPMS Alarm Icon

BLAUPUNKT-Honda-and-Toyota-Plug-and-Play-Tire-05

External Sensor

  1. Sensor Cover
  2. Battery Holder
  3. Battery
  4. Sensor
  5. Rubber Seal
  6. Base BLAUPUNKT-Honda-and-Toyota-Plug-and-Play-Tire-06

Valve Sensor

  1. Dust Cap
  2. Aluminum Alloy Nut
  3. Aluminum Alloy Valve
  4. Transmitter

Display Installation BLAUPUNKT-Honda-and-Toyota-Plug-and-Play-
Tire-07 BLAUPUNKT-Honda-and-Toyota-Plug-and-Play-
Tire-08

WIRING DIAGRAM BLAUPUNKT-Honda-and-Toyota-Plug-and-Play-
Tire-09

Internal sensor installation BLAUPUNKT-Honda-and-Toyota-Plug-and-Play-
Tire-10

External sensor installation

Sensor technical parameters

  • Operating frequency:433.92±0.05MHz
  • Battery voltage:1.8V~3.3V
  • Working temperature:-30℃~60℃(External), -40℃~125℃(Internal)
  • Pressure range:0~8 Bar/0~116 PSI

Display technical parameters

  • Operating current:<20mA
  • Operating voltage:+12V
  • Operating temperature:-30℃~80℃
  • Pressure display range:0~6.8Bar/0~99PSI

Default Value

  • High pressure value:3.1 Bar/45 PSI
  • Low pressure value:1.8 Bar /26 PSl
  • High temperature value:80℃
  • Tire Warning(For example, Front left tire)

Function list

  • P1. Sensor Pairing
  • P2. Tire Position Exchange Setting (Internal sensor use the function)
  • P3. Threshold Value Setting
  • P4. Unit Switching

Note: Press &Hold the setting button 3s, Screen will going into function, you can click Setting button to switch these function from P1 to P4, and press &hold the OK button 3s, will sure that you want to operate functions, then Press & hold the setting button to exit setting interface.

Sensor Pairing Setting

  1. Long press Set 3s
  2. Display P1
  3. Press OK, FL tire will waiting new ID

BLAUPUNKT-Honda-and-Toyota-Plug-and-Play-Tire-01

Once you install or reinstall FL external sensor, or inflated or deflated FL tire and keeping 20s at least, screen will display new ID number, and give a success sound of DI, then will turn to FR tire automatic.
Note: Before leaving the factory, we have matched ID of sensor.

Threshold Value Setting

  1. Long press Set button
  2. Click Set button 2times again, screen display P3.BLAUPUNKT-Honda-and-Toyota-Plug-and-Play-Tire-03
  3. Press OK button, then press the set button to switch between High Pressure Value & Low Pressure Value interface.
  4. Click OK , Value will flash, then click SET button to adjust the threshold Value Setting that you like.
  5. Click OK to sure that the value suitable with your tire.
  6. Press & hold the setting button to exit setting interface.

Accessories

BLAUPUNKT-Honda-and-Toyota-Plug-and-Play-Tire-04

Documents / Resources

| BLAUPUNKT Honda and Toyota Plug and Play Tire Pressure Monitoring System [pdf] User Manual
Honda and Toyota Plug and Play Tire Pressure Monitoring System, Plug and Play Tire Pressure Monitoring System, Tire Pressure Monitoring System, Pressure Monitoring System
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals