CoverPro 10×20 Portable Car Canopy Owner’s Manual
- June 10, 2024
- COVERPRO
Table of Contents
CoverPro 10×20 Portable Car Canopy
Save This Manual Keep this manual for the safety warnings and precautions,
assembly,operating, inspection, maintenance and cleaning procedures. Write the
product’s serial number in the back of the manual near the assembly diagram
(or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken,please call 1-888-866-5797 as soon as possible.
WARNING
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
IMPORTANT SAFETY INFORMATION
WARNING
Read all safety warnings and instructions.
Failure to follow the warnings and instructions may result in serious injury.
Save all warnings and instructions for future reference.
The warnings, precautions, and instructions discussed in this instruction
manual cannot cover all possible conditions and situations that may occur. It
must be understood by the operator that common sense and caution are factors
which cannot be built into this product, but must be supplied by the operator.
Assembly Precautions
- Do not assemble in windy conditions.
- Assemble and install only on flat, level, hard surface.
- Assemble and anchor only according to these instructions. Improper assembly or inadequate anchoring can create hazards.
- Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly.
- Keep assembly area clean and well lit.
- Keep bystanders out of the area during assembly.
- Do not assemble when tired or when under the influence of drugs or medication.
- Product capabilities apply to properly and completely assembled product only.
Use Precautions
-
Do not use grill or any other type of fire under cover. Cover may catch fire if exposed to heat rising from fire.
-
Do not allow snow or debris to accumulate on this item.
-
Heavy, wet snow or strong wind could cause damage or sudden collapse. Remove the Cover when these or similar conditions are expected.
-
This product is not a toy. Do not allow children to play with or near this item.
-
Use as intended only.
Do not use for long-term shelter. -
Inspect regularly, tighten all loose hardware and loose cords, and secure all loosened anchors. If any parts are damaged, bent, or stretched, they must be replaced. Hardware may loosen during normal operation stresses. Loose hardware or damaged/altered parts will compromise the structural integrity of this product.
-
Maintain product labels and nameplates.
These carry important safety information.
If unreadable or missing, contact Harbor Freight Tools for a replacement.
Specifications
| Center Height | 9′ 6″ |
|---|---|
| Side Height | 6′ 5″ |
Assembly
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of
this product.
WARNING
TO PREVENT SERIOUS INJURY:
Do not leave this product partially assembled. Assemble this product
completely at one time.
Note: For additional information regarding the parts listed in the following pages,refer to Parts List and Diagram on page 10.
Note: Much of this product’s assembly is done using slip-fit construction. Make sure all parts seat completely and securely. A rubber mallet (sold separately) can be used to gently tap parts in place to ensure a tight fit.
-
Assemble one half of the roof using 8x Swaged Tubes (2), 3x Rafter Tubes (3),
4x Straight Cross Tubes (4), 4x 3-Way Connectors (5), and 2x 4-Way Connectors (6).
Align the 3- and 4-Way Connectors so that the free ends are all on
the same side of the assembly, as shown in Figure 1.
-
Connect a Rafter Tube (3) to each 3- and 4-Way Connector (5,6) at the top of the roof.
Connect 4x Swaged Tubes (2), 2x Straight Cross Tubes (4), 2x 3-Way Connectors (5), and 1x 4-Way Connector (6) together, then attach that assembly to the ends of the Rafter Tubes (3).
-
Place the Roof Tarp (9) over the top of the roof assembly with its eyelet straps facing down, on the inside.
-
Use the Ball Tie-downs (10) to attach the Roof Tarp to the tubes using the eyelets on the eyelet straps.
-
Attach a Straight Tube (1) to each 3- and 4-Way Connector (5, 6) on one side of the assembly.
Note: The warning label is on one of the Straight Tubes (1).
Turn that Tube so that the Warning label can be read easily.
Attach a Swaged Tube (2) to the bottom of each Straight Tube.
-
Attach a Straight Tube (1) to each 3- and 4-Way Connector (5, 6) on the other side of the assembly.
Attach a Swaged Tube (2) to the bottom of each Straight Tube.
-
Place a Foot Plate (8) over the bottom of each Swaged Tube (2).
Use two Base Fastening Stakes (7) through each Foot Plate to anchor the Canopy.
Note: Verify that there are no utility lines nearby before driving anchors. -
For each corner of the Roof Tarp (9)
- Connect the Tarp Corner Hook (11) to the hole on the inside corner of the Straight Tube (1).
- Pull the end of the Rope snug and tie it off.
-
Drive a Rope Fastening Stake (12) about 3 feet away from each corner of the canopy, angled inward.
Tie a Rope (13) around the 3-Way Connector (5) at each corner of the Canopy, then attach it to the Stake (12).
Note: Verify that there are no utility lines nearby before driving anchors.
Maintenance
Procedures not specifically explained in this manual must be performed only by a qualified technician.
TO PREVENT SERIOUS INJURY FROM PRODUCT FAILURE:
Do not use damaged products. If damage is noted, have the problem corrected
before further use.
MONTHLY, inspect the general condition of the Portable Garage. Check for:
- loose ratchet tie downs, anchors, tube connections, and rail clamps (tighten as needed),
- torn or frayed covers, ropes, or cables,
- cracked, bent, or broken parts, and
- any other condition that may affect its safe operation.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE
IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT
OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Parts List and Diagram
Parts List
Note: Individual part illustrations not to scale.
Record Product’s Serial Number Here:
Note:
- If product has no serial number, record month and year of purchase instead.
- Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Specify UPC 193175335357 when ordering parts.
Assembly Diagram
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us
with transportation charges prepaid. Proof of purchase date and an explanation
of the complaint must accompany the merchandise. If our inspection verifies
the defect, we will either repair or replace the product at our election or we
may elect to refund the purchase price if we cannot readily and quickly
provide you with a replacement. We will return repaired products at our
expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost
of returning the product.
This warranty gives you specific legal rights and you may also have other
rights which vary from state to state.
Visit our website at: http://www.harborfreight.com
Email our technical support at:
productsupport@harborfreight.com
When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken,please call 1-888-866-5797 as soon as possible.
Copyright© 2015 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described
herein. Tools required for assembly and service may not be included.
Download PDF:CoverPro 10×20 Portable Car Canopy Owner’s Manual
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>