MEILAN X3 Cute Eye Smart Bike Tail Light User Guide
- June 15, 2024
- MEILAN
Table of Contents
- MEILAN X3 Cute Eye Smart Bike Tail Light
- PRODUCT INFORMATION
- FAQ
- Remote control mounted on handlebar
- Place the CUTE EYE near the top of the seatpost
- Remove light body
- Secure on saddle rail
- Buttons and functions
- How to pair
- Enable and disable automatic brake warning function
- Specifications
- Charging
- Replacement of remote control battery
- Safety statement and warranty
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
MEILAN X3 Cute Eye Smart Bike Tail Light
PRODUCT INFORMATION
Remote control mounted on handlebar
- Place the CUTE EYE near the top of the seatpost.
- Image: A hand placing the CUTE EYE on a bicycle’s seatpost.
- Image: A hand adjusting the position of the CUTE EYE on the seatpost.
- Image: Side view of the CUTE EYE mounted on the seatpost at approximately 60 degrees angle.
- Remove light body: Slightly press the fixed buckle and take out the light body.
- Image: A hand pressing the buckle and sliding the light body to remove it.
- Image: A close-up view of a hand pressing the buckle on the light body.
- Secure on saddle rail:
- Image: A hand holding the mounting bracket with CUTE EYE detached.
- Image: The mounting bracket detached from the CUTE EYE.
- Image: The light body of CUTE EYE with the bracket’s position indicated for attachment.
- Image: A hand positioning the mounting bracket on the saddle rail of a bicycle.
- Image: The mounting bracket being secured onto the saddle rail with a screw.
- Image: The light body of CUTE EYE being attached to the mounted bracket on the saddle rail.
Buttons and functions
- Short press: the laser light is always on/flashing/off.
- Short press: light mode switch. Long press: the tail light turns off. If there is no movement for 30 minutes, the tail light will enter the automatic shutdown state. You must long press the button to turn it on again.
- Short press: turn left. Short press again: stop left turn signal.
- Short press: turn right. Short press again: stop right turn signal.
- Short press: change light mode. Long press: turn on. Long press again: turn off.
- Image: Diagram of the CUTE EYE with button functions labeled.
How to pair?
Remote control and tail light pairing: Turn off CUTE EYE. Long press and
hold the button until two yellow lights appear on the right (CUTE EYE is in
the pairing mode). Short press any button on the remote control and start
pairing. CUTE EYE is successfully paired when it appears full yellow light
mode.
Enable and disable automatic brake warning function
- witch automatic brake warning functions in the charging state. Press and hold the button for 1 second, if four red lights in the middle flashing irregularly, it means the automatic brake function has been enabled; if four red lights in the middle stay on, it means automatic brake function has been disabled.
- CUTE EYE uses a built-in chip to intelligently detect the occurrence of braking behavior. Due to the diversity of road conditions and personal usage habits, 100% accurate detection is currently not available. If it affects your using experience, please turn off this function.
- Reminder: this product uses lasers that comply with the American UL standard in the global area. Laws and regulations may apply to some European countries, the products sold by sellers may not contain laser light function. Please pay attention to the notification.
Specifications1. Battery type: | rechargeable 18650 lithium battery, 2500 mAh |
---|---|
2. Wireless transmission method: | Bluetooth BLE4.0 |
3. Working frequency band: | 2.4G HZ |
4. Ambient temperature: | -10 to 40 °C |
5. Waterproof level: | IPX6 |
Charging
- TYPE-C port, input DC 5V, 1A
- Image: Diagram of the CUTE EYE charging port location.
Replacement of remote control battery
- Please replace the battery in the remote control when the LED no longer lights up. The remote control is powered by a CR2032 button battery. Please use a standard brand battery. The battery has positive and negative polarity. Please install it in the correct way.
- Unlock the buckle of the plastic shell as shown in the figure down below. Take out the circuit board and the battery to place the new one.
-
- Image: A hand opening the remote control’s battery compartment.
- Image: The remote control with the battery compartment open, displaying the circuit board.
- Image: A hand using a tool to remove the battery from the remote control.
- Image: The new battery being placed into the remote control.
- Image: The circuit board and new battery properly installed in the remote control.
- Image: The remote control being closed after the battery replacement.
Safety statement and warranty
- Do not throw used batteries into water or an uncontrolled natural environment. Do not place this product on fire or in an extremely high temperature environment.
- When the product is not used continuously for six months, please charge it at least once before using.
- This product is suitable to use from light to moderate rain. Do not use the product in the heavy rain or immerse it in water.
- The automatic turning function provided by this product is only an auxiliary reminder function. Due to temporary change of the road or uncontrollable factors in product itself, the turning indication may violate your actual driving direction. Please do not take CUTE Eye’s turning indication as the main safety guarantee. Consumers shall bear the personal and property safety losses caused thereby.
- This product was developed in accordance with the EN300328V1.9.1 standard. Please observe the local laws and regulations when using it in different countries and regions.
- The product is guaranteed for one-year warranty for non-human damage (from the date of sale), and the accessories are covered by the warranty. You can contact the after-sales service through MEILAN global distributors or by writing to MEILAN.
FAQ
-
How do I install the CUTE EYE on my bicycle?
You can install the CUTE EYE by placing it near the top of the seatpost and securing it with the provided mounting bracket. -
How do I charge the CUTE EYE?
The CUTE EYE is charged using a TYPE-C port with an input of DC 5V, 1A. -
How can I replace the battery in the remote control?
To replace the battery, open the battery compartment, remove the old CR2032 battery, and install the new one ensuring correct polarity. -
What should I do if the automatic brake warning function is not working accurately?
If the automatic brake warning function is affecting your use due to inaccurate detection, you can disable this function. -
Is the CUTE EYE waterproof?
The CUTE EYE has a waterproof level of IPX6, making it suitable for use in light to moderate rain.
Remote control mounted on handlebar
Place the CUTE EYE near the top of the seatpost
Remove light body
Slightly press the fixed buckle and take out the light body.
Secure on saddle rail
Buttons and functions
- Short press: the laser light is always on/flashing/off.
- Short press: light mode switch.
- Long press: the tail light turns off.If there is no movement for 30 minutes, the tail light will enter the automatic shutdown state You must long press ****to turn it on again
- Short press: turn left.
- Short press again: stop left turn signal.
- Short press: turn right.
- Short press again: stop right turn signal.
- Short press: change light mode.
- Long press: turn on.
- Long press again: turn off.
How to pair
Remote control and tail light pairing
Turn off Cute Eye. Long press and hold ****until two yellow lights appear on
the right (Cute Eye is in the pairing mode). Short press any button on the
remote control and start pairing. Cute Eye is successfully paired when it
appears full yellow light mode.
Enable and disable automatic brake warning function
- Switch automatic brake warning functions in the charging state. Press and hold ****button for 1 second, if four red lights in the middle flashing irregularly, it means the automatic brake function has been enabled; if four red lights in the middle stay on, it means automatic brake function has been disabled.
- Cute Eye uses a built-in chip to intelligently detect the occurrence of braking behavior. Due to the diversity of road conditions and personal usage habits, 100% accurate detection is currently not available. If it affects your using experience, please turn off this function.
Reminder: this product uses lasers that comply with the American UL standard in the global area. Laws and regulations may apply to some European countries, the products sold by sellers may not contain laser light function. Please pay attention to the notification.
Specifications
- Battery type: rechargeable 18650 lithium battery, 2500 mAn
- Wireless transmission method: Bluetooth BLE4.0
- Working frequency band: 2.4G HZ
- Ambient temperature: -10 to40°C
- Waterproof level: IPX6
Charging
TYPE-C port, input DC 5V, 1A
Replacement of remote control battery
- Please replace the battery in the remote control when the LED no longer lights up. The remote control is powered by a CR2032 button battery. Please use a standard brand battery. The battery has positive and negative polarity. Please install it in the correct way.
- Unlock the buckle of the plastic shell as shown in the figure down below. Take out the circuit board and the battery to place the new one.
Safety statement and warranty
- Do not throw used batteries into water or an uncontrolled natural environment. Do not place this product on fire or in an extremely high temperature environment.
- When the product is not used continuously for six months, please charge it at least once before using.
- This product is suitable to use from light to moderate rain. Do not use the product in the heavy rain or immerse it in water.
- The automatic turning function provided by this product is only an auxiliary reminder function. Due to temporary change of the road or uncontrollable factors in product itself, the turning indication may violate your actual driving direction. Please do not take Cute Eye’s turning indication as the main safety guarantee. Consumers shall bear the personal and property safety losses caused thereby.
- This product was developed in accordance with the EN300328V1.9.1 standard. Please observe the local laws and regulations when using it in different countries and regions.
- The product is guaranteed for one-year warranty for non-human damage (from the date of sale), and the accessories are not covered by the warranty. You can contact the after-sales service through MEILAN global distributors or by writing to MEILAN.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>