Orbit HT25 Smart Hose Watering Timer from B-hyve User Guide
- June 11, 2024
- Orbit
Table of Contents
Orbit HT25 Smart Hose Watering Timer from B-hyve User Guide
Box Contents
A. Hose Faucet Timer
B. Wi-Fi Hub
C. Quick Start Guide
Open the B-hyve App
Log into your B-hyve account and go to devices under settings to add the Hose
Faucet Timer as a new device. The app will walk you through the rest of the
process.
For new users, search for “B-hyve” and download the free Android or iOS app. Create an account to begin timer setup.
Power Your Wi-Fi Hub
Write down the MAC address:
12-digit alphanumeric code on the back of the hub.
Hub Mac Address: 
Plug the hub into an indoor outlet within range of your B-hyve device and Wi-
Fi signal..
Avoid areas where the signal must travel through dirt or thick steel barriers.
Enter Pairing Mode
Press the B-hyve button to enter into pairing mode. Your hub will flash a blue light every 5 seconds.
Power Your Hose Faucet Timer
Insert two new AA Batteries*, the timer is now in pairing mode and will flash a blue light every 5 seconds.
You will also hear two clicks about 6 seconds apart, this is normal and ensures the valve is closed before you turn on the water.
Write down the MAC address: 12 digit alphanumeric code on the bottom of the timer.
Timer MAC Address:
If at any time you need to re-pair or do a factory reset, press the on/off button quickly 5 times.
Batteries are sold separately. Replace batteries when timer flashes a red
light every 5 seconds, or when the app notifies you that batteries need
replacing.
If you remove or change the batteries you will need to reconnect to Bluetooth® to set the correct time and date.
Install the Timer
Your timer is now ready to be used with any product that can be attached to a standard hose faucet.
Do not place the timer in an underground valve box.
Turn on Your Water
The water must remain on for the timer to work properly.
Manual Watering
Simply press and hold the on/off button for 5 seconds to activate manual watering.
Need to stop watering, even during a programmed time? Press the on/off button once to stop watering.
Timer
Range: 150 ft without interference
Pressure Operating Range: 10-100 PSI
Temperature Operating Range:
32°F-158°F (0-70°C)
For Outdoor Use With Cold Water Only
Not For Use With Appliances
Do Not Mix Alkaline, Standard (Carbon-Zinc), or
Rechargeable (Nickel Cadmium) Batteries.
Used up or dead batteries must be removed from the
timer and disposed of properly.
Do not dispose of batteries in fire.
Batteries may explode or leak.
Hub
Range: 150 ft withoutinterference
Temperature Operating Range: 32°F-104°F (0-40°C)
Storage Temperature: -4°F to 140°F (-20 °C to 60 °C)
Humidity Operating Range: 0–90%
Input: 100-240V ~ 50/60Hz 0.2A
Output: 5V-1.0A
For Indoor Use Only
FCC Statement: FCC ID: ML6HT25 & ML6-BH1
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation. FCC Warning: Any changes or modifications not expressly
approved by the party responsible for compliance could void the user’s
authority to operate this equipment. Note: This equipment has been tested and
found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct
the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from the receiver’s.
- Consult the dealer or an experienced radio/TV technician for help
This device meets the FCC and IC requirements for RF exposure in public or controlled environments. The end user is advised to maintain a distance 20 cm from the timer and any personnel to ensure compliance with RF exposure regulations.
IC Statement: IC: 3330A-HT25 & 3330A-BH1 This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This Class B digital apparatus complies with Canadian ICES-003.
Need Help?
If you encounter a problem, please use the following resources before retuning your B-hyve to the store.
Scan the QR Code for access to a full user manual, videos, and more.
call us
1-800-488-6156
Text us
801-797-2319
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>