DEWALT DCD7771 20V Cordless Brushless Drill Instruction Manual
- June 9, 2024
- Dewalt
Table of Contents
- DCD7771 20V Cordless Brushless Drill
- INTENDED USE
- DRILL/DRIVER/HAMMERDRILL SAFETY WARNINGS
- Additional Safety Warnings for Drills
- Additional Safety Information
- BATTERIES AND CHARGERS
- Storage Recommendations
- Battery Pack Cleaning Instructions
- Charging a Battery (Fig. C)
- Important Charging Notes
- Charger Cleaning Instructions
- Wall Mounting
- ASSEMBLY AND ADJUSTMENTS
- Speed Selection (Fig. A)
- Mode Selection (Fig. A)
- OPERATION
- Installing and Removing the Battery Pack (Fig. E)
- Proper Hand Position (Fig. F)
- MAINTENANCE
- Cleaning
- Accessories
- Repairs
- SPECIFICATIONS
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Instruction Manual
DCD7771
20V Max 1/2″ (13 mm) Brushless Compact Drill/Driver
DCD7781
20V Max 1/2″ (13 mm) Brushless Compact Hammer drill
www.DEWALT.com
Questions? See us on the World Wide Web at
www.DEWALT.com
(original instructions)
DCD7771 20V Cordless Brushless Drill
Fig. A
DCD7771
Components
1 Battery pack
2 Battery release button
3 Variable speed trigger
4 Forward/reverse control button
5 Mode selection collar
6 Speed selector| 7 Work light
8 Keyless chuck
9 Belt hook (Optional accessory)
10 Mounting screw
11 Bit clip (Optional accessory)
12 Main handle
---|---
Fig. B
| 75–100% charged
---|---
| 51–74% charged
| < 50% charged
| Pack needs to be charged
Fig. C
Indicators
Charging|
---|---
Fully Charged|
Hot/Cold Pack Delay|
MAXIMUM RECOMMENDED CAPACITIES
| DCD7771| DCD7781
---|---|---
Wood| 1″ (25 mm)| 1″ (25 mm)
Steel| 1/2″ (13 mm)| 1/2″ (13 mm)
Masonry| –| 1/2″ (13 mm)
WARNING: Read all safety warnings and all instructions. Failure to follow
the warnings and instructions may result in electric shock, fire and/or
serious injury.
WARNING: To reduce the risk of injury, read the instruction manual.
INTENDED USE
These drills/drivers/hammer drills are designed for professional drilling,
screw driving and hammer drilling applications.
DO NOT use under wet conditions or in presence of flammable liquids or gases.
DO NOT let children come into contact with the tool. Supervision is required
when inexperienced operators use this tool.
Definitions: Safety Alert Symbols and Words
This instruction manual uses the following safety alert symbols and words to
alert you to hazardous situations and your risk of personal injury or property
damage.
DANGER: Indicates an imminently hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided,
may result in minor or moderate injury.
(Used without word) Indicates a safety related message.
NOTICE: Indicates a practice not related to personal injury which, if not
avoided, may result in property damage.
GENERAL POWER TOOL SAFETY WARNINGS
WARNING: Read all safety warnings, instructions, illustrations and
specifications provided with this power tool. Failure to follow all
instructions
listed below may result in electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE.
The term “power tool” in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.
1. Work Area Safety
a ) Keep work area clean and well lit. Cluttered or dark areas invite
accidents.
b ) Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c ) Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
2. Electrical Safety
a ) Power tool plugs must match the outlet. Never modify the plug in any way.
Do not use any adapter plugs with earthed (grounded) power tools. Unmodified
plugs and matching outlets will reduce risk of electric shock.
b ) Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c ) Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
d ) Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool.
Keep cord away from heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
e ) When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.
f ) If operating a power tool in a damp location is unavoidable, use a ground
fault circuit interrupter (GFCI) protected supply. Use of a GFCI
reduces the risk of electric shock.
3. Personal Safety
a ) Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inattention while operating power
tools may result in serious personal injury.
b ) Use personal protective equipment. Always wear eye protection. Protective
equipment such as a dust mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce personal injuries.
c ) Prevent unintentional starting. Ensure the switch is in the off‑position
before connecting to power source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the switch or energizing
power tools that have the switch on invites accidents.
d ) Remove any adjusting key or wrench before turning the power tool on. A
wrench or a key left attached to a rotating part of the power tool may result
in personal injury.
e ) Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
f ) Dress properly. Do not wear loose clothing or jewelry. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewelry or long
hair can be caught in moving parts.
g ) If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
h ) Do not let familiarity gained from frequent use of tools allow you to
become complacent and ignore tool safety principles. A careless action can
cause severe injury within a fraction of a second.
4. Power Tool Use and Care
a ) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the
rate for which it was designed.
b ) Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and must be
repaired.
c ) Disconnect the plug from the power source and/ or remove the battery pack,
if detachable, from the power tool before making any adjustments,
changing accessories, or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d ) Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands of untrained users.
e ) Maintain power tools and accessories. Check for misalignment or binding of
moving parts, breakage of parts and any other condition that may affect the
power tool’s operation. If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power tools.
f ) Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
g ) Use the power tool, accessories and tool bits etc. in accordance with
these instructions, taking into account the working conditions and the
work to be performed. Use of the power tool for operations different from
those intended could result in a hazardous situation.
h ) Keep handles and grasping surfaces dry, clean and free from oil and
grease. Slippery handles and grasping surfaces do not allow for safe handling
and control of the tool in unexpected situations.
5. Battery Tool Use and Care
a ) Recharge only with the charger specified by the manufacturer. A charger
that is suitable for one type of battery pack may create a risk of fire when
used with another battery pack.
b ) Use power tools only with specifically designated battery packs. Use of
any other battery packs may create a risk of injury and fire.
c ) When battery pack is not in use, keep it away from other metal objects,
like paper clips, coins, keys, nails, screws or other small metal objects,
that can make a connection from one terminal to another. Shorting the battery
terminals together may cause burns or a fire.
d ) Under abusive conditions, liquid may be ejected from the battery; avoid
contact. If contact accidentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected from the battery may
cause irritation or burns.
e ) Do not use a battery pack or tool that is damaged or modified. Damaged or
modified batteries may exhibit unpredictable behavior resulting in fire,
explosion or risk of injury.
f ) Do not expose a battery pack or tool to fire or excessive temperature.
Exposure to fire or temperature above 265 °F (130 °C) may cause explosion.
g ) Follow all charging instructions and do not charge the battery pack or
tool outside the temperature range specified in the instructions. Charging
improperly or at temperatures outside the specified range may damage the
battery and increase the risk of fire.
6. Service
a ) Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power
tool is maintained.
b ) Never service damaged battery packs. Service of battery packs should only
be performed by the manufacturer or authorized service providers.
DRILL/DRIVER/HAMMERDRILL SAFETY WARNINGS
-
Safety Instructions for All Operations
a ) Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss.
b ) Brace the tool properly before use. This tool produces a high output torque and without properly bracing the tool during operation, loss of control may occur resulting in personal injury.
c ) Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting accessory or fasteners may contact
hidden wiring. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock. -
Safety Instructions When Using Long Drill Bits a ) Never operate at higher speed than the maximum speed rating of the drill bit. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal injury.
b ) Always start drilling at low speed and with the bit tip in contact with the workpiece. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal injury.
c ) Apply pressure only in direct line with the bit and do not apply excessive pressure. Bits can bend causing breakage or loss of control, resulting in personal injury .
Additional Safety Warnings for Drills
-
Do not operate this tool for long periods of time.
Vibration caused by the operating action of this tool may cause permanent injury to fingers, hands, and arms. Use gloves to provide extra cushion, take frequent rest periods, and limit daily time of use. -
Hammer bits and tools get hot during operation.
Wear gloves when touching them.
Additional Safety Information
WARNING: Never modify the power tool or any part of it. Damage or
personal injury could result.
WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety
glasses. Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR
CERTIFIED SAFETY EQUIPMENT:
- ANSI Z87.1 eye protection (CAN/CSA Z94.3),
- ANSI S12.6 (S3.19) hearing protection,
- NIOSH/OSHA/MSHA respiratory protection.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
- lead from lead-based paints,
- crystalline silica from bricks and cement and other masonry products, and
- arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
- Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals. Direct particles away from face and body.
- Use the appropriate dust extractor vacuum to remove the vast majority of static and airborne dust. Failure to remove static and airborne dust could contaminate the working environment or pose an increased health risk to the operator and those in close proximity.
- Use clamps or other practical ways to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control and injury.
- Air vents often cover moving parts and should be avoided. Loose clothes, jewelry or long hair can be caught in moving parts.
CAUTION: When not in use, place tool on its side on a stable surface
where it will not cause a tripping or falling hazard. Some tools with large
battery packs will stand upright on the battery pack but may be easily knocked
over.
The label on your tool may include the following symbols. The symbols and
their definitions are as follows:
V | volts | Ah | amp hours |
---|---|---|---|
Hz | hertz | or AC | alternating current |
min | minutes | or AC/DC | alternating or direct current |
or DC | direct current | Class II Construction |
(double insulated)
| Class I Construction
(grounded)| no| no load speed
…/min| per minute| n| rated speed
BPM| beats per minute| | earthing terminal
IPM| impacts per minute| | safety alert symbol
RPM| revolutions per
minute| | visible radiation
sfpm| surface feet per
minute| | wear respiratory protection
SPM| strokes per minute| | wear eye protection
A| amperes| | wear hearing protection
W| watts| | read all documentation
Wh| watt hours| |
BATTERIES AND CHARGERS
The battery pack is not fully charged out of the carton.
Before using the battery pack and charger, read the safety instructions below
and then follow charging procedures outlined. When ordering replacement
battery packs, be sure to include the catalog number and voltage.
READ ALL INSTRUCTIONS
Important Safety Instructions for All Battery Packs
WARNING: Read all safety warnings, instructions, and cautionary markings for
the battery pack, charger and product. Failure to follow the warnings and
instructions may result in electric shock, fire and/or serious injury.
-
Do not charge or use the battery pack in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Inserting or removing the battery pack from the charger may ignite the dust or fumes.
-
NEVER force the battery pack into the charger. DO NOT modify the battery pack in any way to fit into a non‑compatible charger as battery pack may rupture causing serious personal injury. Consult the chart at the end of this manual for compatibility of batteries and chargers.
-
Charge the battery packs only in DEWALT chargers.
-
DO NOT splash or immerse in water or other liquids.
-
DO NOT allow water or any liquid to enter battery pack.
-
Do not store or use the tool and battery pack in locations where the temperature may reach or exceed 104 °F (40 °C) (such as outside sheds or metal buildings in summer). For best life store battery packs in a cool, dry location.
NOTE: Do not store the battery packs in a tool with the trigger switch locked on. Never tape the trigger switch in the ON position. -
Do not incinerate the battery pack even if it is severely damaged or is completely worn out. The battery pack can explode in a fire. Toxic fumes and materials are created when lithium-ion battery packs are burned.
-
Do not expose a battery pack or appliance to fire or excessive temperature. Exposure to fire or temperature above 265 °F (130 °C) may cause explosion.
-
Follow all charging instructions and do not charge the battery pack or appliance outside of the temperature range specified in the instructions. Charging improperly or at temperatures outside of the specified range may damage the battery and increase the risk of fire.
-
If battery contents come into contact with the skin, immediately wash area with mild soap and water. If battery liquid gets into the eye, rinse water over the open eye for 15 minutes or until irritation ceases. If medical attention is needed, the battery electrolyte is composed of amixture of liquid organic carbonates and lithium salts.
-
Contents of opened battery cells may cause respiratory irritation. Provide fresh air. If symptoms persist, seek medical attention.
-
Battery liquid may be flammable if exposed to spark or flame.
-
Never attempt to open the battery pack for any reason. If the battery pack case is cracked or damaged, do not insert into the charger. Do not crush, drop or damage the battery pack. Do not use a battery pack or charger that has received a sharp blow, been dropped, run over or damaged in any way (e.g., pierced with a nail, hit with a hammer, stepped on). Damaged battery packs should be returned to the service center for recycling.
Storage Recommendations
The best storage place is one that is cool and dry, away from direct sunlight and excess heat or cold. Store the fully charged battery pack out of the charger.
Battery Pack Cleaning Instructions
Dirt and grease may be removed from the exterior of the battery pack using a cloth or soft non-metallic brush. Do not use water or any cleaning solutions.
Fuel Gauge Battery Packs (Fig. B)
Some battery packs include a fuel gauge. When the fuel gauge button is pressed
and held, the LED lights will indicate the approximate level of charge
remaining. This does not indicate tool functionality and is subject to
variation based on product components, temperature, and end-user application.
Transportation
- WARNING: Fire hazard. Do not store, carry, or transport the battery pack so that metal objects can contact exposed battery terminals. For example, do not place the battery pack in aprons, pockets, tool boxes, product kit boxes, drawers, etc., with loose nails, screws, keys, coins, hand tools, etc.
When transporting individual battery packs, make sure that the battery terminals are protected and well insulated from materials that could contact them and cause a short circuit. NOTE: Li-ion battery packs should not be put in checked baggage on airplanes and must be properly protected from short circuits if they are in carry-on baggage.
Shipping the DEWALT FLEXVOLT™ Battery Pack
The DEWALT FLEXVOLT™ battery pack has a battery cap that should be used when
shipping the battery pack.
Attach the cap to the battery pack to ready it for shipping.
This converts the battery pack to three separate 20V batteries. The three
batteries have the Watt hour rating labeled “Shipping” on the battery pack. If
shipping without the cap or in a tool, the pack is one battery at the Watt
hour rating labeled “Use”.
Example battery pack label: USE: 120 Wh SHIPPING: 3 x 40 Wh
In this example, the battery pack is three batteries with 40 Watt hours each when using the cap. Otherwise, the battery pack is one battery with 120 Watt hours.
Important Safety Instructions for All
Battery Chargers
WARNING: Read all safety warnings, instructions, and cautionary markings for the battery pack, charger and product. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
- DO NOT attempt to charge the battery pack with any chargers other than a DEWALT charger. DEWALT chargers and battery packs are specifically designed to work together.
- These chargers are not intended for any uses other than charging DEWALT rechargeable battery packs. Charging other types of battery packs may cause them to overheat and burst, resulting in personal injury, property damage, fire, electric shock or electrocution.
- Do not expose the charger to rain or snow.
- Do not allow water or any liquid to enter charger.
- Pull by the plug rather than the cord when disconnecting the charger. This will reduce the risk of damage to the electric plug and cord.
- Make sure that the cord is located so that it will not be stepped on, tripped over or otherwise subjected to damage or stress.
- Do not use an extension cord unless it is absolutely necessary. Use of improper extension cord could result in risk of fire, electric shock or electrocution.
- When operating a charger outdoors, always provide a dry location and use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
- An extension cord must have adequate wire size for safety. The smaller the gauge number of the wire, the greater the capacity of the cable, that is, 16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. When using more than one extension to make up the total length, be sure each individual extension contains at least the minimum wire size. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The lower the gauge number, the heavier the cord.
Voltage <Volts) | Total length of cord in meters (m) |
---|---|
120-127V | 0-7 |
220-240V | 0-15 |
Rated Ampere Ranae | **Minimal cross-sectional area of the cord in meters |
(mm2 )**
0-6A| 1.0| 1.5| 1.5| 2.5
6-10A| 1.0| 1.5| 2.5| 4.0
10-12A| 1.5| 1.5| 2.5| 4.0
12-16A| 2.5| 4 0| Not Recommended
- Do not place any object on top of the charger or place the charger on a soft surface that might block the ventilation slots and result in excessive internal heat. Place the charger in a position away from any heat source. The charger is ventilated through slots in the top and the bottom of the housing.
- Do not operate the charger with a damaged cord or plug. Have them replaced immediately.
- Do not operate the charger if it has received a sharp blow, been dropped or otherwise damaged in any way. Take it to an authorized service center.
- Do not disassemble the charger; take it to an authorized service center when service or repair is required. Incorrect reassembly may result in a risk of electric shock, electrocution or fire.
- The charger is designed to operate on standard 120V–127 (low voltage) or 220V–240V (high voltage) household electrical power. Do not attempt to use it on any other voltage. This does not apply to the vehicular charger.
- Foreign materials of a conductive nature, such as, but not limited to, grinding dust, metal chips, steel wool, aluminum foil or any buildup of metallic particles should be kept away from the charger cavities and ventilation slots.
- Always unplug the charger from the power supply when there is no battery pack in the cavity.
Charging a Battery (Fig. C)
- Plug the charger into an appropriate outlet.
- Insert and fully seat battery pack. Red charging light will continuously blink while charging.
- Charging is complete when the red charging light remains continuously ON. Battery pack can be left in charger or removed. Some chargers require the battery pack release button to be pressed for removal.
- Charger will not charge a faulty battery pack, which may be indicated by the light staying OFF. Take charger and battery pack to an authorized service center if light stays OFF.
NOTE: Refer to label near charging light on charger for blink patterns. Older chargers may have additional information and/or may not have a yellow indicator light.
Hot/Cold Pack Delay
When the charger detects a battery pack that is too hot or too cold, it
automatically starts a Hot/Cold Pack Delay, suspending charging until the
battery pack has reached an appropriate temperature. The charger then
automatically switches to the pack charging mode. This feature ensures maximum
battery pack life.
A cold battery pack may charge at a slower rate than a warm battery pack.
The hot/cold pack delay will be indicated by the red light continuing to blink
but with the yellow light continuously ON. Once the battery pack has reached
an appropriate temperature, the yellow light will turn OFF and the charger
will resume the charging procedure.
DCB118 and DCB1112 Chargers
The DCB118 and DCB1112 chargers are equipped with an internal fan designed to
cool the battery pack. The fan will turn on automatically when the battery
pack needs to be cooled.
Electronic Protection System
Li-Ion tools are designed with an Electronic Protection System that will
protect the battery pack against overloading, overheating or deep discharge.
The tool will automatically turn off and the battery pack will need to be
recharged.
Important Charging Notes
-
The charger and battery pack may become warm to the touch while charging. This is a normal condition, and does not indicate a problem. To facilitate the cooling of the battery pack after use, avoid placing the charger or battery pack in a warm environment such as in a metal shed or an uninsulated trailer.
-
If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp or other appliance;
b. Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights;
c. If charging problems persist, take the tool, battery pack and charger to your local service center. -
You may charge a partially used pack whenever you desire with no adverse effect on the battery pack.
Charger Cleaning Instructions
WARNING: Shock hazard. Disconnect the charger from the AC outlet before cleaning. Dirt and grease may be removed from the exterior of the charger using a cloth or soft non-metallic brush. Do not use water or any cleaning solutions.
Wall Mounting
Some DEWALT chargers are designed to be wall mountable or to sit upright on a
table or work surface. If wall mounting, locate the charger within reach of
an electrical outlet, and away from a corner or other obstructions which may
impede air flow. Use the back of the charger as a template for the location of
the mounting screws on the wall. Mount the charger securely using drywall
screws (purchased separately) at least 1” (25.4 mm) long, with a screw head
diameter of 0.28–0.35” (7–9 mm), screwed into wood to an optimal depth leaving
approximately 7/32” (5.5 mm) of the screw
exposed. Align the slots on the back of the charger with the exposed screws
and fully engage them in the slots.
SAVE THESE INSTRUCTIONS FOR FUTURE USE
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal injury, turn unit off and remove the battery pack before making any adjustments or removing/ installing attachments or accessories. An accidental start-up can cause injury.
Installing a Bit or Accessory into a Keyless Chuck (Fig. D)
WARNING: Do not attempt to tighten drill bits (or any other accessory) by
gripping the front part of the chuck and turning the tool on. Damage to the
chuck and personal injury may result. Always lock off trigger switch and
disconnect tool from power source when changing acces sories.
WARNING: Always ensure the bit is secure before starting the tool. A
loose bit may eject from tool causing possible personal injury.
To insert a drill bit or other accessory, follow these steps.
- Turn tool off and remove battery pack.
- Grasp the black sleeve of the chuck with one hand and use the other hand to secure the tool. Rotate the sleeve counterclockwise far enough to accept the desired accessory.
- Insert the accessory about 3/4″ (19 mm) into the chuck 8 and tighten securely by grasping and rotating the chuck sleeve 13 clockwise with one hand while holding the tool with the other. When the chuck is nearly tightened you will hear a clicking sound. After 12-14 clicks the chuck is securely tightened around the accessory. Your tool is equipped with an automatic spindle lock mechanism. This allows you to open and
close the chuck with one hand.
Be sure to tighten chuck with one hand on the chuck sleeve and one hand holding the tool for maximum tightness. To release the accessory, repeat steps 1 and 2 above.
Speed Selection (Fig. A)
The tool features two speed settings for greater versatility.
NOTE: Do not change speeds when the tool is running. Always allow the
tool to come to a complete stop before changing speed.
- To select speed 1 (higher torque setting), slide the speed selector 6 back (away from the chuck).
- To select speed 2 (lower torque setting), slide the speed selector forward (towards the chuck).
If the tool does not change speeds, confirm that the speed selection switch is completely engaged in the forward or back position.
Mode Selection (Fig. A)
The mode selection collar 5 can be used to select the correct operating mode
depending upon the planned application.
To select, rotate the collar until the desired symbol aligns with the arrow.
WARNING: When the mode selection collar is in the drill or hammer drill
positions, the drill will not clutch.
The drill may stall if overloaded, causing a sudden twist.
Symbol | Mode |
---|---|
Drilling | |
1-15 | Screw driving (higher number = greater torque) |
Hammer drilling |
OPERATION
WARNING: To reduce the risk of serious personal injury, turn unit off and
remove the battery pack before making any adjustments or removing/
installing attachments or accessories. An accidental start-up can cause
injury.
Installing and Removing the Battery Pack (Fig. E)
NOTE: For best results, make sure your battery pack is fully charged.
To install the battery pack 7 into the tool handle, align the battery pack
with the rails inside the tool’s handle and slide it into the handle until the
battery pack is firmly seated in the tool and ensure that it does not
disengage. To remove the battery pack from the tool, press the release button
2 and firmly pull the battery pack out of the tool handle. Insert it into the
charger as described in the charger section of this manual.
Proper Hand Position (Fig. F)
WARNING: To reduce the risk of serious personal injury, ALWAYS use proper
hand position as shown.
WARNING: To reduce the risk of serious personal injury, ALWAYS hold
securely in anticipation of a sudden reaction.
Proper hand position requires one hand on the main handle 12 and the other
hand holding the battery pack 1 .
Variable Speed Trigger and Forward/ Reverse Control Button (Fig. A)
The tool is turned on and off by pulling and releasing the variable speed
trigger 3 . The farther the trigger is depressed, the higher the speed of the
tool. Your tool is equipped with a brake. The chuck will stop as soon as the
trigger switch is fully released.
A forward/reverse control button 4 determines the rotational direction of the
tool and also serves as a lock-off button.
- To select forward rotation (clockwise), release the trigger and depress the forward/reverse control button on the right side of the tool.
- To select reverse (counterclockwise), depress the forward/reverse control button on the left side of the tool.
NOTE: The center position of the control button locks the tool in the off
position. When changing the position of the control button, be sure the
trigger is released.
NOTE: Continuous use in variable speed range is not recommended. It may
damage the switch and should be avoided.
NOTE: The first time the tool is run after changing the direction of
rotation, you may hear a click on start up. This is normal and does not
indicate a problem.
Work light (Fig. A)
The work light 7 is activated when the trigger switch is depressed, and will
automatically turn off 20 seconds after the trigger switch is released. If the
trigger switch remains depressed, the work light will remain on.
NOTE: The work light is for lighting the immediate work surface and is not
intended to be used as a flashlight.
Performing an Application (Fig. A)
WARNING: To reduce the risk of personal injury, ALWAYS ensure workpiece
is anchored or clamped firmly.
WARNING: Always wait until the motor has come to a complete standstill
before changing the direction of rotation.
Prior to Performing Work
- Set the speed selector 6 . Refer to Speed Selection.
- Install the appropriate bit or accessory into the chuck. Refer to Installing a Bit or Accessory into a Keyless Chuck.
WARNING:
- Do not use this tool to mix or pump easily combustible or explosive fluids (benzine, alcohol, etc.).
- Do not mix or stir flammable liquids labeled accordingly.
Screw driving
Your tool has a clutch with adjustable torque for driving and removing a wide
array of fastener shapes and sizes. The numbers 1–15 on the mode selection
collar 5 are used to set a torque range for screw driving. The higher the
number on the collar, the higher the torque and the larger the fastener which
can be driven.
- Turn the mode selection collar 5 to the desired position. Refer to Mode Selection.
- Pull the trigger switch applying pressure in a straight line with the bit until the fastener is seated at the desired depth in the workpiece.
Recommendations for Screw driving
- Start with lower torque settings, then advance to higher torque settings to avoid damage to the workpiece or fastener.
- Make some practice runs in scrap or on unseen areas of the workpiece to determine the proper position of the mode selection collar.
Drilling
-
Turn the mode selection collar 5 to the drill symbol.
Refer to Mode Selection. -
Place drill bit in contact with the workpiece.
NOTE: Use sharp drill bit only. -
Pull the trigger switch applying pressure in a straight line with the bit until it reaches the desired depth.
WARNING: Drill may stall if overloaded causing a sudden twist. Always expect the stall. Grip the drill firmly to control the twisting action and avoid injury. -
Keep the motor running when pulling the bit back out of a drilled hole to prevent jamming.
Recommendations for Drilling
-
When drilling, always apply pressure in a straight line with the bit, but do not push hard enough to stall the motor or deflect the bit.
-
IF THE DRILL STALLS:
– RELEASE TRIGGER SWITCH IMMEDIATELY, remove drill bit from work, and determine cause of stalling.
– DO NOT DEPRESS TRIGGER SWITCH ON AND OFF IN AN ATTEMPT TO START A STALLED DRILL—
THIS CAN DAMAGE THE DRILL.
– To minimize stalling or breaking through the material, reduce pressure on drill and ease the bit through the last fractional part of the hole. -
Large holes (5/16″ to 1/2″ [7.9 mm to 12.7 mm]) in steel can be made easier if a pilot hole (5/32″ to 3/16″ [4 mm to 4.8 mm]) is drilled first.
-
If drilling thin material or material that is prone to splinter, use a wood “back-up” block to prevent damage to the workpiece.
Hammer drilling DCD7781
IMPORTANT: Use carbide-tipped or masonry bits rated for percussion
drilling only.
- Select the desired speed/torque range using the speed selector 6 to match the speed and torque to the planned operation. Turn the mode selection collar 5 to the hammer drill symbol.
- Pull the trigger, applying just enough pressure on the hammer to keep it from bouncing excessively or “rising” off the bit.
Recommendations for Hammer drilling
- Too much force will cause slower drilling speeds, overheating, and a lower drilling rate.
- A smooth even flow of material indicates the proper drilling rate.
- Drill straight, keeping the bit at a right angle to the work. Do not exert side pressure on the bit when drilling as this will cause clogging of the bit flutes and a slower drilling speed.
- When drilling deep holes, if the hammer speed starts to drop off, pull the bit partially out of the hole with tool still running to help clear debris from the hole.
MAINTENANCE
WARNING: To reduce the risk of serious personal injury, turn unit off and
remove the battery pack before making any adjustments or removing/
installing attachments or accessories. An accidental start-up can cause
injury.
Your DEWALT power tool has been designed to operate over a long period of time
with a minimum of maintenance. Continuous satisfactory operation depends upon
proper tool care and regular cleaning.
Cleaning
WARNING: Blow dirt and dust out of all air vents with clean, dry air at
least once a week. To minimize the risk of eye injury, always wear approved
eye protection when performing this procedure.
WARNING: Never use solvents or other harsh chemicals for cleaning the
non-metallic parts of the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened only with water and mild
soap. Never let any liquid get inside the tool; never immerse any part of the
tool into a liquid.
Accessories
WARNING: Since accessories, other than those offered by DEWALT, have not
been tested with this product, use of such accessories with this tool could be
hazardous.
To reduce the risk of injury, only DEWALT recommended accessories should be
used with this product.
Recommended accessories for use with your tool are available at extra cost
from your local dealer or authorized service center.
Repairs
The charger and battery pack are not serviceable.
WARNING: To assure product SAFETY and RELIABILITY, repairs, maintenance
and adjustment (including brush inspection and replacement) should be
performed by a DEWALT factory service center or a DEWALT authorized service
center. Always use identical replacement parts.
SPECIFICATIONS
DCD7771 | DCD7781 | 20V Max* |
---|
Compatible battery packs and chargers
*20V Max li-Ion**
Battery Packs| DCB200, DCB201, DCB203, DCB204, DCB204BT, DCB205, DCB205BT,
DCB206, DCB208,
DCB210, DCB230, DCB240, DCBP034
---|---
Chargers| DCB101, DCB103, DCB104, DCB107, DCB112, DCB113, DCB115, DCB118,
DCB132
- Maximum initial battery voltage (measured without a workload) is 12, 20, 60 or 120 volts. Nominal voltage is 10.8, 18, 54 or 108. (120V Max is based on using 2 DEWALT 60V Max lithium-ion batteries combined.)
NOTE: The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth®, SIG, Inc. and any use of such marks by DEWALT is under license. Other trademarks and trade names are those of their respective owners.
Made in China
DEWALT Industrial Tool Co. 701 East Joppa Road, Towson, MD 21286
Copyright © 2021
The following are trademarks for one or more DEWALT power tools: the yellow
and black color scheme, the “D” shaped air intake grill, the array of pyramids
on the handgrip, the kit box configuration, and the array of lozenge-shaped
humps on the surface of the tool.
NA142126
References
- DEWALT® Power Tools Official Site | Guaranteed Tough®
- Ferramentas Elétricas | Armazenagem | Acessórios | DEWALT Brasil
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>