PRIMO Bluetooth control Smart Strip Lighting Led box User Manual
- June 9, 2024
- PRIMO
Table of Contents
Bluetooth control Smart Strip Lighting Led box
User Manual
Bluetooth control Smart Strip Lighting Led box
NOTES:
PRINT ON MAGAZINE PAPER PRINT GRAYSCALE ONE SIDE ONLY
NOTE: Fold Accordion Style
INSTALLATION
Plug In
-
Plug the controller into the device with a USB interface Make sure the indicator light on the device is flashing rapidly, indicating the device is ready to connect.
-
Measure the area you wish to attach the LED strip to. Ensure that the ore has a clean, solid surface.
-
Measure the LED strip for the desired length, starting at the end closest to the connector for the Bluetooth Controller.
IMPORTANT: If you measure 8 cut from the opposite end, you will not be able to connect the LED strip to the Bluetooth Controller. -
Locate the closest cut mark to your desired length. Each strip has cut markings located every 10cm. Take a sharp pair of scissors or blade, and cut along the cut mark.
-
LED Strip Adhesive Installation ‘Follow Instructions Carefully Be sure to thoroughly clean surface or wall with any standard rubbing alcohol before applying adhesive and let dry.
Position LED strip upon surface and press every section firmly for at least 30
seconds ensuring a strong hold.
NOTE:
3M adhesive may not adhere well to vinyl surfaces nor to delicate wallpaper.
FCC Warning:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly
approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure requirement.The
device can be used in portable exposure condition without restriction.
DOWNLOAD APP
Download the SmartLife App from App Store or Google Play. If you would like to
enjoy the features of SmartLife as a guest, click on “Try Me”. Otherwise,
follow these steps to register:
Register an account on your SmartLife App.
- Enter your mobile phone number or email address
- Enter the verification code and create a password.
- Log in to the App.
ADD NEW DEVICE
*Make sure your mobile phone Bluetooth is turned on. If he device is Flashing, open Smart Life App on
When connecting the device, you can see the connection status as shown in the
picture. Once connected, a page will open. Select the room of your home where
the device is located and press
Now your new device is ready to be controlled via the App. Connection
Failed
If the Application shows “Device Adding Timeout”, it means that the device
connection has failed. Please check your network and follow the instructions
in the notification. Then try to connect it again.
DEVICE CONTROL
After connecting the device, automatically it will open the page to control it by the application With the keys you find at bottom page, you can:
- Change the color of 16 million color and brightness.
- Dim 1%-100%.
- Select one if the scenarios already created for you.
- Select one of preset music mode already created for you.
- Set more information like schedule.Do Not Disturb. Default Light.Gradient in page
. 
Sharing Devices
You can share your devices with your family and friends who has already
downloaded Smart Life App and registered a new account.
The people you shared your devices with will be able to control them, but they
will not be able to add new devices to your home or delete shared devices.
Recommended Sharing Method
If the recipient is a household member or other trusted user tap: Me > Home
Management > Add Member and add the recipient to your home. Then, devices in
the home can be shared with the new user.
WARNINGS & PRECAUTIONS
- Please do not use or store the equipment in the wet environment such as the bathroom or in a place with dust or dirt. This may damage components and electronic components.
- Do not place the equipment in an overheated place. High temperature will shorten the service life of electronic equipment and damage the plastic parts of the product.
- Do not strongly impact or rub the equipment, which may damage its precise structure.
- Do not use strong chemicals, cleaning products or strong detergent to dean the equipment.
- Do not use in flammable and explosive environment.
- If you find abnormal conditions such as odor, heating, discoloration or deformation, please stop using the equipment and contact us immediately.
- During operation, if radio frequency interference occurs, the light band may not work.
- Do not put it in a place where infants can reach. Children should use it under the supervision of their parents.
- When this product is powered on, please pay attention to power safety.
- It can only be used indoors.