PestWest Mantis Sirius Wall-Mounted Black Dual Voltage Insect Light Trap Instruction Manual
- June 9, 2024
- PestWest
Table of Contents
**Insect Light Systems (LTs)**
INSTRUCTIONS FOR USE
Confidence in
Fly Control www.pestwest.com
Mantis Sirius Wall-Mounted Black Dual Voltage Insect Light Trap
INSTRUCTIONS FOR USE.
ALWAYS SWITCH OFF THE SYSTEM BEFORE SERVICING.
PRODUCT DESCRIPTION
All PestWest flying insect management systems are manufactured with only the
highest quality materials. The bodywork is powder coated zintec steel (rust-
resistant) with a polished aluminum reflector (Stainless steel 304 grade front
cover also available). The system utilizes a PestWest glue board. PestWest
systems are engineered with Quantum BL lead-free, FEP coated, shatter
resistant lamps.
The Mantis Sirius is a front-of-house/public area, flying insect system that
provides optimally energy efficient Quantum T5 lamp technology. A state of the
art, energy efficient, high frequency system designed for all public areas.
The Sirius is handcrafted with an electronic ballast, so no starters are
required. The solid state ballast powers two T5 (5/8”) Quantum lamps
thatdramatically increase performance and reliability at a decreased cost.
PRECAUTIONS
All PestWest insect light traps are fully insulated, class 1 appliances, nevertheless, reasonable precautions must be observed:
- Always switch off the system before servicing.
- Do not install in wet or damp environments or where dangerous concentrations of flammable gases or dusts are likely to occur.
- Ensure the system is properly grounded.
- Do not allow the glue board to become over-filled with dead insects. Change at regular intervals as required by the catch or at least every 6-8 weeks. Use only PestWest replacement glue boards.
- The system is designed for indoor use only.
- Not suitable for use in barns, stables or similar locations.
- Keep out of reach of children.
UNPACKING YOUR SIRIUS
Each system is carefully inspected and packed before leaving our factory.
Before discarding the outer carton, examine for obvious signs of transport
damage. Remove the system and pay particular attention to the removal of all
packing materials before installation.
OPERATION
Insect light traps operate on the principle that most flying insects are
attracted to light, particularly to the ultraviolet (UV) end of the light
spectrum. Since insects also fly at night and have less competitive lighting,
systems must operate 24 hours a day.
LOCATION OF THE SYSTEM
System efficacy can be affected by the intensity of other light sources
(overhead lighting and daylight), therefore locate the system where
competition from other light sources is minimal. For best results, install all
your systems using the PestWest UV-A Meter.
In food areas, mount close to, but not directly over, exposed food or
preparation surfaces. Observe where the flies tend to congregate and
interception zones, and mount your system close to that area. Mount systems
adjacent to fly ingress points (service/overhead doors and windows). Mount the
system above head level and clear of
any traffic (do not position the system over lockout, tag-out areas).
INSTALLATION
The PestWest Mantis Sirius is engineered with a 6.6ft (2m) power cord ending
in a Nema 5-15 US plug, and operates from a 110-277V 50-60Hz supply. Be
certain the power cord is properly secured. A licensed electrician must
perform any extensions to the power cord.
Using the screws and masonry rawl plugs provided, the system has 4 keyhole
slots on the rear panel to permit wall mounting. The system can be mounted
either horizontally or vertically, in any orientation, enabling the power cord
to exit the system on whichever side is preferred, to best suit the electrical
outlet location, and provide a neat installation.
The system is supplied, as standard, to be mounted with the switch under the
main chassis, or vertically in either orientation. If theses mounting options
are chosen, there is no need to remove and rotate the front cover.
NOTE: In certain orientations, the cover may need to be rotated, to
prevent the glue board dropping out of the system. Refer to ‘FRONT COVER
ROTATION’ for instructions. Only 2 Keyholes should be used for horizontal
mounting, while 4 keyholes should be used in vertical mounting.
Using the template provided, mark the necessary points onto the mounting
surface. Drill to a depth of 1 1/2” using a 7/32” drill bit. Insert the
plastic wall anchor into the drilled hole and insert the screw into the wall
anchor. DO NOT TIGHTEN. Once the screw is flush with the wall loosen
(counterclockwise) 2 complete turns to bring the screw head approx 2/5” above
the wall surface. The system will now hook over the screws because of the
keyhole feature. Adjust tightness as necessary.
Before installing the glue board, remove the paper backing from the glue
surface (do not touch the glue surface).
FRONT COVER ROTATION (OPTIONAL)
Unscrew the 4 screws which are securing the cover to the mount panel using a
pozidrive (or phillips) screwdriver. Ensure the cover is rotated so that the
‘board stop’ feature on the board guides is located to whichever face of the
system has been selected to be the underside. Failure to do this will result
in the glue board falling out of the system.
Replacement of the cover is the opposite procedure of removal.
It may also be beneficial to rotate the cover when mounting the system in the
vertical orientation, if for example the system is being located near to the
corner of a room, which would otherwise limit access when replacing the glue
board.
HARDWIRING THE SYSTEM
CAUTION – Ensure the main power supply is switched off.
For direct wiring, the system has a knockout in the rear panel. For the
electrical connections, a terminal block is located inside the enclosure. This
option can be used for hardwiring 220-240V 50-60Hz electrical supplies.
This option must be performed by a licensed electrician. The existing power
cord should be removed and discarded.
The system must be disassembled by removing both the front cover and reflector
components.
Using a grounded pozidrive or phillips screwdriver, remove the 4 screws securing the cover to the mounting panel. Remove the cover. Place the cover front side down on a soft, debris free surface to avoid any scratching. Remove the two lamps and place to one side.
With a grounded screwdriver, remove the 4 remaining screws securing the
reflector. Remove the reflector to gain access to the internal wiring. If
additional access is required, the lamp holders can be removed by depressing
the plastic retaining clips with a small flat screwdriver (depress the clips
gently to avoid breaking them).
Using a grounded screwdriver, remove the small screws on the connector block
which are holding in place the live and neutral wires leading from the power
cord and pull them out of the connector block. Next unfasten the M4 nut which
is securing the ground wire. Remove the nut, the top spring washer and the
grounding wire leading from the power cord. The power cord can now be removed
by compressing the strain relief bushing. Discard the cord.
By wedging a flat head screwdriver into the knockout slit and gently tapping
the screwdriver with a hammer, remove the knockout panel. Once the edge of the
knockout is bent, you can then grip the corner with pliers and twist until the
securing tabs break loose. If the edges of the hole are sharp, they should be
gently filed down to ensure no wires will be cut or damaged.
WIRING DIAGRAM
To rewire the system, run the fixed wiring through the knockout. The ground
wire should be connected back to the ground stud on the bodywork using an
appropriate ring terminal connector, securing it with both the spring washer
and M4 nut provided. Check that the system is fully grounded and the wire is
secured before
continuing with installation.
Once grounded, the live (black) and neutral (white) wires can then be
reconnected to the connector block as before. Ensure all wires are securely
fastened by firmly tugging on them.
None of the wires running from the ballast OR between the connector block and
the switch should be tampered with.
Once the system is safely rewired, it can be reassembled. Assembly is the
opposite procedure of disassembly.
CLEANING AND MAINTENANCE ALWAYS SWITCH OFF THE SYSTEM BEFORE SERVICING.
To maintain the attractive appearance of the system, wipe down and clean as
often as required.
Use a cloth dampened with water and detergent or a proprietary cleaner. Do not
use scouring pads or abrasives.
The UVA lamps used in insect light traps should be changed at least once per
year. To maintain optimum efficacy, replace with Quantum BL leadfree,FEP
coated, shatter resistant lamps. People cannot see UVA light from UVA BL
lamps, but can see the blue light from UVA BL lamps. The UVA light diminished
over time. Additionally, UVA light decreases proportionately by the distance
from the lamps (Inverse Square Law). Therefore, for optimum placement and
results, use the PestWest UV-AMETER.
Insect light traps should operate 24/7/365. Change lamps at least once per
year (post winter onset of increased fly activity).
Quantum BL lead-free, FEP coated, shatter-resistant lamps are intended for use
in glass exclusion zones. PestWest FEP coating is the highest quality
available. FEP is both UV and operating temperature tolerant while allowing
optimum UVA emission.
CHANGING GLUE BOARDS ALWAYS SWITCH OFF THE SYSTEM BEFORE SERVICING.
Glue boards should be changed when full or at least every 6-8 weeks. Regular
inspections of the glue boards are recommended, as they are not visible in
normal operation.
Remove the old glue board by lifting it out of the guides on the reverse side
of the cover.
(VIEW FROM REAR OF COVER TO SHOW GUIDES AND BOARD POSITION)
Always install PestWest brand glue boards to ensure peak efficiency. To fit
the shape of the Mantis Sirius, the glue board has a perforated crease about 3
inches in from one edge. The board must be separated along this perforation
with the smaller section being discarded.
Remove the backing paper from the new board and slide into the guides on the
reverse side of the over, inserting the first edge along the separation line.
Ensure the glue surface is facing towards the lamp.
CHANGING LAMPS ALWAYS SWITCH OFF THE SYSTEM BEFORE SERVICING.
Grasp and rotate each lamp 90° in either direction until 2 clicks are heard.
Remove the lamps by sliding out of the lamp holders. Installation is the
opposite procedure to removal.
https://www.pestwest.com/us/products/insect-light-traps-glue-board-
systems/mantis-sirius/
Scan the QR code for the Sirius instruction video.
REPLACEMENT PARTS
Glue board type: 135-000047
Universal WHITE Glue board – 135-000064
Universal BLACK Glue Board – 135-000070
Universal YELLOW Glue Board – 135-000171
Lamp type: 130-000177 (PestWest Quantum
BL 14W T5 21” Shatter Resistant)
UVA Meter 325-000038
All PestWest systems are warrantied for 3 years (excluding lamps and glue
boards). The Sirius has been tested for safety, efficacy and quality using
PestWest components. Warranty is void if non-PestWest components are used.
Lamp contains mercury (Hg), dispose or recycle in accordance with applicable
laws. In US, consult www.lamprecycle.org
or 1-800-922-6693 for: measures to be
taken in case of breakage; safe handling procedures; and recycling and
disposal options. Outside of US, please contact your local authorities.
Warranty information must be received and on file with PestWest USA LLC for
proper coverage.
Scan the QR code to register your 3-year warranty or visit
https://support.pestwest.com/pestwest-warranty/
For additional quality products contact PestWest USA LLC at 941.358.1983 or
click to www.pestwest.com *Manufacturer reserves
the right to vary model specifications without notice.
Find us on:
Facebook
Twitter
LinkedIn
Find us on:WARNING: Cancer and/or Reproductive Harm
www.P65Warnings.ca.gov
PestWest Electronics Ltd operates a quality management system certified to ISO
9001
PestWest USA LLC
7135 16th Street E, Suite 124 Sarasota, FL, 34243
Office: 941.358.1983
Fax: 941.358.1916
Toll Free: 866.476.7378
Email: customerservice@pestwest.com
www.pestwest.com
References
- Lamp Recycle – Environmental Responsiblility Starts Here
- P65Warnings.ca.gov
- PestWest LLC USA – Confidence in fly Control
- PestWest Warranty – PestWest Support Portal
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>