RAB A17 300 Watt Ultra Economy LED Area Light Instructions

INSTRUCTIONS
A17™ AREA LIGHT INSTALLATION

RAB Lighting is committed to creating high-quality, affordable, well-designed and energy-efficient LED lighting and controls that make it easy for electricians to install and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: marketing@rablighting.com

IMPORTANT
READ CAREFULLY BEFORE INSTALLING THE FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
RAB fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining the fixture. No user-serviceable parts inside. WARNING: Do not use an electric generator to test LED fixtures. WARNING: Min 75°C SUPPLY CONDUCTORS.

MOUNTING THE UNIVERSAL ARM ON THE FIXTURE

1. Remove the Arm Cover from the Arm by loosening the Arm Cover Screws as shown in Fig. 1.
2. Feed wires from fixture into Arm.
3.  Line up the Arm and fixture. Tighten screws inside the Arm and tighten securely to the housing.
4. Replace the Arm Cover and secure it with Screws as shown in Fig. 2.

Square Pole Mount

1. Place the Bolster Plate inside the Pole as shown in Fig. 3.
2. Remove the Round Pole Adaptor Plate.
3. Fix Arm to Square Pole with Bolt.
4. Open the Arm Cover and pull the wires into the junction box.
5. Feed supply wires from the Pole to connect to the Arm. Make appropriate wire connections per NEC in an approved enclosure (Fig. 7).
6. Use bolts to tighten to the Pole.

Round Pole Mount

1. Place the Bolster Plate inside the Pole as shown in Fig. 3.
2. Fix Arm to Round Pole with Bolt.
3. Open the Arm Cover and pull the wires into the junction box.
4. Feed supply wires from the Pole to connect to the Arm. Make appropriate wire connections per NEC in an approved enclosure (Fig. 7).
5. Use bolts to tighten to the Pole.

SLIPFITTER MOUNT

NOTICE: Adjustable angle is 90°.

1. Place the Slipfitter over the Tenon and secure the Fixture with set Screws on the side of the Slipfitter as shown in Fig. 5.
2. Feed wires from Fixture through Slipfitter and supply wires from the pole. Make the necessary connections in the Slipfitter and knot wires for strain relief.
3. To adjust the angle of the Slipfitter, losen the Locking Bolt and swivel the Fixture to the desired angle. The graduation of the Slipfitter cover plate can be used as guidelines to adjust the angle.
4. Tighten the Locking Bolt (Fig. 6).

0-10V DIMMABLE WIRING

Universal voltage driver permits operation at 120V thru 277V, 50 or 60 Hz. Units ordered with /480 suffix operate at 480V, 50 or 60Hz. For 0-10 Dimming, follow the wiring directions as shown in Fig. 7.

1. Connect the black/brown fixture lead to the LINE supply lead.
2. Connect the white/blue fixture lead to the COMMON supply lead.
3. Connect the green/yellow wire from the fixture to the supply ground. Do NOT connect the GROUND of the dimming fixture to the output.
4. Connect the purple fixture lead to the DIM V+ lead.
5. Connect the pink/gray fixture lead to the DIM V- lead.
6. Cap the yellow fixture lead, if present. Do NOT connect.

CLEANING & MAINTENANCE

CAUTION: Do not open or remove the Respirator Plug as shown in Fig. 8. Be sure the fixture temperature is cool enough to touch. Do not clean or maintain while the fixture is energized.

1.  Clean Polycarbonate lens with non-abrasive glass cleaning solution.
2. Do not open the fixture to clean the LED. Do not touch the LED.

Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance.

  © 2021 RAB LIGHTING Inc. A17-70-375W – IN – 1021 73712-RAB
Easy Answers
rablighting.com
Visit our website for product info
Tech Help Line
Call our experts: 888 722-1000
e-mail Answered promptly – sales@rablighting.com
Free Lighting Layouts
Answered online or by request
RAB WARRANTY: RAB’s warranty is subject to all terms and conditions found at rablighting.com/warranty

References

• Welcome to RAB
• Legal - RAB Lighting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>