MERACH MR-667 Exercise Bike User Manual

: June 10, 2024
: MERACH

Table of Contents

Part List
Assembly Instructions
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Part List

Assembly Instructions

Prepare #2 front stabilizer, two #18 bolts, two #20 standard elastic washers, two #19 flat washers and A: Allen Key.
Put 20# standard elastic washers and 19# flat washers into 18# bolts in turn.
Align the holes on #2 front stabilizer and the front bracket on the #1 main frame.
Put the bolts assembly from step 2 into the two holes on the front stabilizer.
Tighten and secure the bolts with A: Allen Key.
Complete assembly of #2 front stabilizer.
Prepare #3 rear stabilizer, two #18 bolts, two #20 standard elastic washers, two #19 flat washers and A: Allen Key.
Put 20# standard elastic washers and 19# flat washers into 18# bolts in turn.
Align the holes on #3 rear stabilizer and the rear bracket on the #1 main frame.
Put the bolts assembly from step8 into the two holes on the rear stabilizer.
Tighten and secure the bolts with A: Allen Key.
Complete the assembly of #3 rear stabilizer.
Prepare the right pedal (marked R).
Unscrew the locknut on the right pedal (marked R) first.
Prepare right pedal (marked R) and locknut, B: Cross Wrench and C: Open-end Wrench.
Make sure to match the right pedal and the right crankarm (both marked R).
Screw the right pedal (marked R) into the crank.
Tighten the right pedal with the B: Cross Wrench, make sure it’ s fully tightened.
Screw the locknut into the right pedal (marked R).
Tighten the right pedal with the B: Cross Wrench and C: Open-end Wrench, and make sure it’ s fully tightened.
Complete the assembly of right pedal. 22. Prepare the left pedal (marked L)
Unscrew the locknut on the left pedal (marked L) first.
Prepare left pedal (marked L) and locknut, B:Cross Wrench and C: Open-end Wrench.
Make sure to match the left pedal and the left crankarm (both marked L).
Screw the left pedal (marked L) into the crank.
Tighten the left pedal with the B: Cross Wrench, and make sure it’ s fully tightened.
Screw locknut into the left pedal (marked L).
Screw Locknut into Left pedal marked
Tighten the left pedal with the B: Cross Wrench and C: Open-end Wrench, and make sure it s fully tightened.
Complete the assembly of left pedal.
Prepare #10 adjust assembly on seat cushion, #16 knob and #17 flat washer.
Put the #10 adjust assembly on seat cushion onto seat post.
Then put the 17# flat washer into the Knob
Tighten the #16 knob into #10 Seat .
Make sure the adjust assembly on seat cushion will not wobble.
Loosen the knob pre-locked on the #1 main frame, then pull it outward.
Pull the knob outward with one hand, then insert the #7 handle adjustment tube to #1 main frame with the other hand.
Align the knob to the adjustment hole in #7 handle adjustment tube and then tighten this knob.
Prepare #6 handlebar, two #21 bolts, #12 bolt and A: Allen Key.
Align the #6 handle to the #1 main frame.
Put the two #21 bolts into the left two
Put the #12 bolt into the right hole. holes.
Tighten and secure #12 bolt and the two #21 bolts with A: Allen Key.
Prepare #8 handle decorative cover.
Press #8 handle decorative cover on the #6 handle.
Prepare #9 tablet holder, two 13# bolts, two #15 standard elastic washers, two #14 ARC washers and B: Cross Wrench.
Put 15# standard elastic washers and I
Align the #9 tablet holder to the #6 14# ARC washers into 13# bolts in turn. handle.
Put the bolts assembly from step 47
Tighten and secure the two #13 bolts into the two holes on both sides. with B: Cross Wrench.
Complete the assembly of #9 tablet I
Prepare #4 bottle cage, two 22# bolts holder. and B: Cross Wrench.
Align the #4 bottle cage to the #6 handle.
Insert two #22 bolts into the holes, Tighten and secure the two #22 bolts with B: Cross Wrench.
Complete the assembly of #4 bottle cage.
Prepare the 11# foot pad.
Tilt the machine, screw the 11# foot pad into the main frame, and then lay the machine flat. Adjust the foot pads to be leveled with the arni inn
Complete assembly.

Descriptions:

If the Overall balance of the is not good user can adjust it through 4 foot pads of the front and rear foot tube.
Rotating the foot pads can make them fully support the ground and the bike will no longer wag from side to side

@merachfit