Hydrus PC03 Cordless Pool Vacuum User Manual

Hydrus PC03 Cordless Pool Vacuum

Product introduction

• Model: Roker Plus
• Features: The cordless rechargeable robotic pool cleaner is well-designed for use in any situation without any hassle. Thanks to its compact and lightweight design, it is suitable for pools of various sizes. It can clean the bottom of a pool without draining the water. With an affordable price, it delivers a more effective, deeper, and perfect cleaning result.

Thank you for choosing our robotic pool cleaner. Read this manual carefully before use and follow the instructions. Keep this manual in a safe place for future reference.

Safety instructions

1. Read this manual carefully and use the device accordingly. We are not liable for any loss or injury caused by improper use of the device.
2. The device is only intended for use on flat-bottomed pools.
3. Before using this device, ensure the water depth of the pool is at least 50 cm away from the top of the device.
4. Keep humans and animals out of the pool while the device is working in it. Do not leave children unsupervised while using the device.
5. Turn off the switch before cleaning the filter and the bottom of the device.
6. The device comes with a built-in lithium battery. Do not disassemble the sealed compartment without authorization. Protect the device from direct sunlight and strong impacts.
7. Be sure to charge the device before first use.
8. During the idle period, charge the device once a month to protect its battery.
9. pH [7.0-7.8], temperature [4-34 °C], chlorine [max. 4.0 ppm], sodium chloride [max. 5,000 ppm].

Overview

Accessories

• R oker Plus x 1
• Filt er x 1
•  warranty x 1
• User Manual x 1
• Quic k Guide x 1
• P ower Adapter x 1
• Car toon Sticker x 3
• Pic k-up Hook x 1

Technical data

• Dimensions (L x W x H): 363 x 363 x 212 mm
• Weight: 3.2 kg
• Battery capacity: 2,600 mAh
• Battery life :75 mins
• Motor power: 20 W
• Charging time: 2~2.5 hours
• Power adapter/Input voltage: 100-240 V
• Power adapter/Output voltage: 12.6 V
• Power adapter/Rated power: 19 W
• Operating temperature: 0 to 35 °C
• Storage temperature: -10 to 40 °C
• Filter density: 180 μm
• Water depth supported: 0.5-3 m
• Moving speed: 40~60 ft/min
• Waterproof level: IP68
• PH value supported: 7.0~7.8

Helpful tips

1. Turn off the device after it gets out of the water.
2. Af minutes tsh bee deforevic char finishing tes Chelsea devising, ite. Pla is rceec theme device d t in ao co wait pla fo cr 2e0 when charging. Do not cover the device with anything to prevent damage to the internal components caused by overheating.
3. W and stheon tpshe w boarkttering. Thy is loe w, t buzzehe der gevicneera ateutos ama beteicap aftlly moer tvhees t deo tvicehe po is toakl een dge out.
4. Af device e a and play useth, rinsed device ree in asi dua col pool aol wand deter ay placed into, and anal away fabric in tm have t sources.
5. Clean or replace the filter if the suction effect is found to be weakened.
6. The steps.is the device cannot climb. Put it into the water area which is away from
7. For than or three best during the cleaning r ro consult was, park aging prse matchless. sure to clean the filter more

OPERATION

WARNING: When the device is working, do not enter the water or get close to the device to prevent accidents. The operator must monitor on-site and give prompts and warnings. Our company won’t be responsible for the liabilities caused if the operator fails to do so

Charging
Be sure to charge the device before first use; Turn it off before charging; The water spray cover should not touch  the ground when placing the device）

Observe the indicator on the charger:

1. Red indicates the device is not fully charged；
2. Green indicates the device is fully charged；
3. The devices. water spray cover should not touch the ground when placing the

Entering the pool

WARNING: Be sure to charge the device before first use）

1. The devices t are their device or n o residences a do lown ang been purchased and they sh portwe beer swap acreh. Thread；
2. Put the device on its bottom；
3. Grab the handle and put the device on the water surface；
4. W ait for the device to automatically sink to the pool bottom.

Getting out of the pool

WARNING: Install the pick-up hook on the pick-up rod. Be careful when using it. Make sure the device is turned off when it is  not in use）

1. Use the pick-up hook to grab the handle and drag the device out of the water (do not drag too fast);
2. Take the device out after the water inside the device is drained completely;
3. Turn the device off；
   Note: After the device is out of water, if a short beep is heard every 3s, turn off the device immediately; if a short, rush, and loud beep is heard, turn off the device and charge it immediately.

Cleaning

1. Gently force apart both sides of the buckle and slightly shake the device to separate the stand from the upper part of the device body. Lift the upper part of the body;
2. Remove the filter to expose the garbage;
3. Rinse the residual garbage on the filter;
4. Rinse the residual garbage on the stand.

Installation

1.  Align the card slots on both sides of the filter with the stand cards and press them down;
2.  Align the buckle on the upper part of the device body with the stand card location, and force to combine them;
3. Place the device in a cool place to dry for 20 minutes before charging.

FAQs

In case of any problems other than those described above, you can contact us to avoid unnecessary losses.

Troubleshooting

• Tel: 800-618-8968
• Website: www.hydrusbots.com
• E-mail: support@hydrusbots.com
• Work time: Mon-Fri, 09:00-18:00 (EST)

References

• Hydrus | The Most Advanced Intelligent & Cordless Robotic Pool Cleaner

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>