Urevo URTM027 Spacewalk E2 Walking Treadmill Instruction Manual

Urevo URTM027 Spacewalk E2 Walking Treadmill

IMPORTANT SAFETY INSTRUCTIONS

DANGER – To reduce the risk of electric shock:

1. Always unplug this appliance from the electrical outlet immediately after using and before cleaning.

WARNING – To reduce the risk of burns, fire, electric shock, or injury to persons:

1. An appliance should never be left unattended or plugged in. Unplug from outlet when not in use, and before putting on or taking off parts.

2. Do not operate under a blanket or pillow. Excessive heating can occur and cause fire, electric shock, or injury to persons.

3. Close supervision is necessary when this appliance is used by, on, or near children, invalids, or disabled persons.

4. Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.

5. Never operate this appliance if it has a damaged cord or plug if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the appliance to a service center for examination and repair.

6. Do not carry this appliance by supply cord or use cord as a handle.

7. Keep the cord away from heated surfaces.

8. Never operate the appliance with the air openings blocked. Keep the air openings free of lint, hair, and the like.

9. Never drop or insert any object into any opening.

10. Do not use outdoors.

11. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.

12. Caution – To reduce the risk of injury from moving parts – Unplug before servicing.

13. Warning – To reduce the risk of Electric shock – Unplug before cleaning or servicing.

14. Warning – Risk of personal injury – Keep children under the age of 13 away from walking treadmill.

15. To disconnect, turn all controls to the position, then remove the plug from the outlet.

16. Connect this appliance to a proper outlet only. See grounding instructions.

17. This appliance is not intended for use by persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for
    their safety. Keep children under the age of 13 away from this walking treadmill.

18. The maximum weight capacity for this product is 242 kg/110kg. DO NOT EXCEED THE MAXIMUM WEIGHT CAPACITY

SAVE THESE INSTRUCTIONS

GROUNDING INSTRUCTIONS:
This product must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electricity and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

DANGER – Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

SAFETY NOTICE

SPECIFICATION

Performance indictors| Detailed parameters| Performance indictors| Detailed parameters
---|---|---|---

Product dimension

| 123 x 49 x 12 cm|

Minimum speed

|

0.6 mph

48.4 x 19.3 x 4.7 inch

Walking Area

| 40 x 103 cm|

Maximum speed

|

4.0 mph

15.7 x 40.6 inch

Gross weight

| 17.4 KG|

Rate voltage

|

110 – 120V –

38.4 Lbs

Net weight

| 20 KG|

Maximum load

| 110 KG
44.1 Lbs| 242 Lbs
Peak horsepower| 2.0Hp| Rated power| 440W

PRODUCT INTRODUCTION

BEFORE START AND STORAGE

Take out appliances from packages

1. Unbox and take out the accessory box.

2. Lift out the appliance and place at flat surface.
   Attention : 2-3 persons assist is necessary.

3. It is normal that visible welding marks are residual on the walk belt.

Transportation

1. transportation needs, to unplug the power cord, and to lift the terminal of the appliance.
2. Easy to transport appliances with bottom transportation wheel assists, like wheelbarrows

Connect the power

1. Choose flat ground to place the Walking Treadmill. Do not place it on a thick and soft cushion.

2. Plug in the power cord and switch on the power rock button, you can hear a BI sound from the buzzer, which means the circuit of the appliance has connected with power electricity.
   Warning: MUST use the power cord with the package
   Storage

3. Power off the appliance and unplug the power cord before the storage process.

Warning: Before starting to work with this product, Please assess your physical condition and perform exercise properly and regularly. Incorrect or excessive training can be harmful to your health, If you feel unwell, Stop exercising immediately and consult with your doctor.

DISPAY SCREEN

As you walk on or run on the treadmill, the display can show the following workout information

Speed

|

0.6-4.0 mph

|

Displays the speed of walking belt.

Calories| 0-999 Kcal| Displays the approximate number of calories you have burned.
Time                                 0:00-99:59 minutes| Displays the elapsed time;
Distance                          00.0-99.9 miles| Displays the distance that you have walked or run.
Infrared Receiver Port                        /| Aiming the receiver when remote control is in use.

OPERATION

Dual operation

• with remote control
• with console buttons The feature of console buttons is identical to the remote control.
  Attention: please get off the treadmill when you intend to control it with console buttons.

ERROR CODE

When an error occurs, an error warning indicator will light up and display its error code.

E01

| Communication was interrupted between the controller and the numeric display.|

Unscrew the motor hood and verify the connection between the controller and the numeric display. Please contact after-sale service if the E01 code has not been eliminated.

Notice: Always power off and unplug the power cord before processing.

E02

|

Flame protection

| 1.  Unscrew the motor hood and verify the connection between the controller and the motor.

2.  Power supply interrupt due to connector loosening or out, please unscrew the motor hood to check.

3.  Please contact after-sale service if the problem CAN NOT solved by the above process.

EOS

|

Over current protection

| 1.  Due to user over limited 110Kg.

2.  Open to check any foreign objects blocking moving parts. ( such as drive motor, idler roller, driver roller, walking belt)

3. The walking belt is overtightened or lacks lubricant. ( please see detailed chapters relate to belt tension and lubricant process )

E06

E07| Software bug| Replace the new controller.

E10

| Communication

interrupted between the signal cable and the console.

|

Unscrew the motor hood and verify the connection of signal cable, please contact after-sale service if the E10 error code has not been eliminated

TROUBLESHOOTING

No working

|

1.  Power rock switch dyfunction

2.  Power supply interrupted. 3. Power cord damaged

| 1.  Replace the new power rock switch if it doesn’t light on.

2.  Make sure that the power cord is plugged into a properly grounded outlet.

3.  Replace the new power cable.

Walking belt slips

|

Walking belt loosen

|

Tighten walking belt tension with hex tool A

( 1/4 a turn both idler roller screw clockwise)

Remote control does not work|

1.  Incorrect use of default

2.  Battery power shortage.

3.  Remote control function

| 1.  Remotor control should be directly aimed at to receiver port when in use.

2.  Replace new battery cells.

3.  Replace new remote control.

Friction noise|

Walking belt off center.

|

See details of the walking belt tension chapter.

CARE AND MAINTENANCE

A. Symptom: walk belt off-centered or slips

The centering walk belt process is as follows:

1. Power off the appliance and unplug the power cord.
2. The manual centering process is as follows:
   • If the walking belt has shifted to the left, use the hex tool to turn the left idler roller screw clockwise 1/4 of a turn(refer to Figure 1 ).
   • If the walk belt has shifted to the right, use the hex tool to turn the right idler roller screw clockwise 1/4 of a turn(refer to figure 2).
3. Appliance MUST work 1-2 minutes. Repeat the manual centering process until the walking belt is centered.

The belt slip-correcting process is as follows:

1. Power off the appliance before operation.
2. Using the hex tool, turn both idler roller screws clockwise 1/2 of a turn (refer to Figure 3).
3. After correcting, please attempt to walk for 1-2 minutes under the 1.0 mph speed setting. Repeat until the walki g belt is properly tightened.

Attention

1. To prevent any injury, don’t place any debris around the appliance before the maintenance process.
2. MUST use the associated hex tool.
3. Take care of the maintenance process. Do not pinch your fingers.

B. Belt lubrication process, follow the instructions below to lubricate the belt.

1. Power off the appliance and unplug the cord.

2. Using the hex tool, turn both idler roller screws counterclockwise till the belt loosen and lifts easily.
   Tips: please mark hex tool rotating cycles when loosening the belt, which is used for adapting belt tension after the lubrication process.

3. Lifting the edges of the belt and spraying lubrication oil at the center of the walking platform evenly. Not necessary to apply spray lubrication oil on the entire walk platform.

4. Lubrication oil volume Per time of maintenance: 5-10ml.
   Attention: it would cause of belt to slip if sprayed too much.

5. Using the hex tool, turn both idler screws clockwise as previous markdown number of turns until the walking belt tightens properly.

6. Power on the appliance and work out for a few minutes, in order to spread lubrication oil to the whole belt surface evenly.
   Attention: No-loading work at 1.0mph speed setting. Lubrication frequency: High recommend 125 Miles Per time.

C : Appliance cleaning.

1. Power off the appliance and unplug the power cord before cleaning.
2. Wipe and clean with a damp cloth, Do not clean with acidic or caustic detergents.
3. Do not clean the opposite of the walk belt.
4. It’s normal few black powders are residual under the appliance after a long working.

WARRANTY

MANUFACTURER’S LIMITED WARRANTY
UREVO warrants to the original purchaser that this product is free from defects in material and workmanship when used for the purpose intended, under the conditions that it has been installed and operated in accordance with UREVO Owner’s Manual. UREVO’s obligation under this warranty applies to the following:

COMPONENT LENGTH OF WARRANTY
Structural Frame 1 year For Home Use Only All Other Components 90 days For Home Use Only Exclusions from Warranty Coverage: UREVO does not warrant against and is not responsible for, and no implied warranty shall be deemed to cover, any product failure, product malfunction, or damages attributable to:

1. Improper installation and/or failure to abide by UREVO’s installation guidelines;
2. Use of this product beyond normal home use, or in an application for which it was not designed;
3. Cosmetic items such as scratches, dents or discolorations;
4. Damage caused by normal wear and tear, vandalism, accidental or by animals;
5. Any act of Nature (such as fire, flooding, snow, ice, hurricanes, earthquakes, lightning or other natural disasters), environmental condition (such as air pollution, mold, mildew, etc.), or staining from foreign substances (such as dirt, grease, oil, etc.);
6. Normal weathering is due to exposure to sunlight, weather, and atmosphere which can cause colored surfaces to among other things, flake, chalk, and accumulate dirt or stains.
7. Improper operation, alteration, handling, storage, abuse, or neglect of the products.

UREVO, using its sole discretion, will either repair or replace free of charge any part(s) proven to be defective under normal home use. Any repair or replacement shall provide no new warranty coverage but shall retain only the remaining portion of the original product’s warranty. This warranty is offered only to the original purchaser and is not transferable. Proof of original purchase is required. When ordering replacement parts please have the following information ready:

1. Order Number
2. Description of Parts (Adding photos or videos would be helpful)
3. Part Number
4. Date of Purchase

FCC STATEMENT

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Thisequipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This Class B digital apparatus complies with Canadian ICES-003.
Cetappareilnumerique de la classe B estconforme a la norme NMB-003 du Canada.

CUSTOMER SERVICE

IMPORTANT: FOR UREVO ONLY
For damaged or defective products, questions, replacement parts, or any other service support, please contact our customer service department by the below methods:
services@urevosports.com
Response Time : 24-48 hours
Emailing us with the Order ID will be the best method to receive a response during peak business hours.
Website: www.urevosports.com
US Support Hotline: (1 )844-998-2473
Hours of Operation:
Monday – Friday : 9 AM – 12 PM; 1 PM – 6 PM (PST)

PLEASE DO NOT RETURN THIS PRODUCT WITHOUT ASKING OUR CUSTOMER SERVICE FIRST.

SCAN THIS QR CORD TO GET THE PRODUCT INSTALLATION OR MAINTENANCE VIDEOS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>