PORTOR LIGHTING PT-WA2-4F7I-3CP 4 Inch LED Economy Slim Wraparound Luminaire Instruction Manual
- June 10, 2024
- PORTOR LIGHTING
Table of Contents
PT-WA2-4F7I-3CP 4 Inch LED Economy
Slim Wraparound Luminaire
Instruction
Manual
PT-WA2-4F7I-3CP 4 Inch LED Economy Slim Wraparound Luminaire
WARNING
- TO REDUCE THE RISK OF DEATH, PERSONAL INJURY OR PROPERTY DAMAGE FROM FIRE, ELECTRIC SHOCK, FALLING PARTS, CUTS/ABRASIONS, AND OTHER HAZARDS READ ALL WARNINGS AND INSTRUCTIONS INCLUDED WITH AND ON THE FIXTURE BOX AND ALL FIXTURE LABELS.
- BEFORE INSTALLING, SERVICING, OR PERFORMING ROUTINE MAINTENANCE UPON THIS EQUIPMENT, FOLLOW THESE GENERAL PRECAUTIONS.
- COMMERCIAL INSTALLATION, SERVICE AND MAINTENANCE OF LUMINAIRES SHOULD BE PERFORMED BY A QUALIFIED LICENSED ELECTRICIAN.
- FOR THE INSTALLATION: IF YOU ARE UNSURE ABOUT THE INSTALLATION OR MAINTENANCE OF THE LUMINAIRES, CONSULT A QUALIFIED LICENSED ELECTRICIAN AND CHECK YOUR LOCAL ELECTRICAL CODE.
- TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR OTHER SHARP OBJECTS.
- DO NOT MAKE OR ALTER ANY OPEN HOLES IN AN ENCLOSURE OF WIRING OR ELECTRICAL COMPONENTS DURING KIT INSTALLATION.
GENERAL WIRING DIAGRAM
WARNING
- TURN OFF ELECTRICAL POWER AT FUSE OR CIRCUIT BREAKER BOX BEFORE WIRING FIXTURE TO THE POWER SUPPLY.
- TURN OFF THE POWER WHEN YOU PERFORM ANY MAINTENANCE.
- VERIFY THAT SUPPLY VOLTAGE IS CORRECT BY COMPARING IT WITH THE LUMINAIRE LABEL INFORMATION.
- ALL WIRING CONNECTIONS SHOULD BE CAPPED WITH UL APPROVED WIRE CONNECTORS.
CAUTION
- AVOID DIRECT EYE EXPOSURE TO THE LIGHT SOURCE WHILE IT IS ON.
- ACCOUNT FOR SMALL PARTS AND DESTROY PACKING MATERIAL, AS THESE MAY BE HAZARDOUS TO CHILDREN.
- RISK OF BURN. DISCONNECT POWER AND ALLOW FIXTURE TO COOL BEFORE CHANGING BULB OR HANDLING FIXTURE.
NOTICE
- GREEN GROUND SCREW PROVIDED IN PROPER LOCATION. DO NOT RELOCATE.
- MINIMUM 90° SUPPLY CONDUCTORS.
- SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
- SUITABLE FOR DRY OR DAMP LOCATION.
INSTALLATION
(ALWAYS TURN OFF THE POWER SUPPLY FROM MAIN CIRCUIT BREAKER FIRST!)
SURFACE MOUNTING
- Remove fixture from the box.
- Remove lens by pulling from one side of the fixture and hinge on the other
- For mounting, using the provided mounting holes on each end of the fixture housing.
- Make sure electrical connections are updated to code.
- Install ballast cover onto fixture.
- Install lens on one side of the fixture and rotate to engage the opposite side.
CHAIN KIT MOUNTING
- Remove fixture from the box.
- Remove lens by pulling from one side of the fixture and hinge on the other
- For mounting, using the provided mounting holes on each end of the fixture housing.
- Make sure electrical connections are updated to code.
- Install ballast cover onto fixture.
- Install lens on one side of the fixture and rotate to engage the opposite side.
CABLE KIT MOUNTING
- Remove fixture from the box.
- Mount cable to the luminaire. Secure the one end of cable to the beam, then insert into hasp, adjust the cable to the desired height.
- Connect to the main power.
FIELD-ADJUSTABLE CCT AND WATTAGE
The end users may adjust the color temperature and lumen output respectively by the two DIP switch buttons integrated into the driver. Each DIP switch is accommodated with 3 options (left, middle and right ), corresponding to 3 color temperatures and 3 powers respectively, which can perform the desired color temperature and lumen output combination.
Factory Default Settings: 3500K @ 25W
- DIP switches are located onto the side of the fixture.
- Select a wattage and color temperature by sliding switch left or right respectively to the desired value.
www.portorlighting.com
Specification subject to change without notice
Documents / Resources
|
PORTOR LIGHTING PT-WA2-4F7I-3CP 4 Inch LED Economy Slim Wraparound
Luminaire
[pdf] Instruction Manual
PT-WA2-4F7I-3CP 4 Inch LED Economy Slim Wraparound Luminaire, PT-WA2-4F7I-3CP,
4 Inch LED Economy Slim Wraparound Luminaire, LED Economy Slim Wraparound
Luminaire, Slim Wraparound Luminaire, Wraparound Luminaire, Luminaire
---|---