RAB SWISH 2X2 Center Basket LED Troffer Instructions
- June 10, 2024
- RAB
Table of Contents
RAB SWISH 2X2 Center Basket LED Troffer Instructions
SWISH 2X2
SWISH 2X4
IMPORTANT
EAD CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR
FUTURE REFERENCE.
RAB fi xtures must be wired in accordance with the National ElectricalCode
and all applicable local codes. Proper grounding is required for safety. THIS
PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE
BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND
THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing the fi xture. No
user serviceable parts inside.
RECESSED CEILING MOUNTING
The fi xture is suitable only for INDOOR RECESSED CEILING application. Above ceiling access required.
To mount in an insulated or non-insulated ceiling – 9/16” or 15/16” exposed Flat Tee Grid Ceiling follow the steps below.
-
Rotate and slide the Housing as required to fi t through the Tee-Grid Bar and place it as indicated by the directional arrow in Fig.1.
-
Firmly bend the pre-installed Grid Clips (4) against the Tee-Grid Bar to secure the Housing.
-
Support wires are required by Installation Codes. Support the Housing to the building structure by Support Wires (supplied by others) through the Support Wire Hole.
-
Make sure that the orientation of the Access Plate faces an accessible tile to make electrical splices.
-
Loosen screw on Access Plate and remove the Access Plate. Knock out appropriate Conduit Knockouts on the Access Plate to route input conduit. Use appropriate conduit connectors as required by code.
-
Connect wires as shown in wiring diagram. Push all wires back into the Splice Box. Be careful not to pinch wires.
WARNING: To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects. -
Replace Access Plate and tighten Access Plate Screw.
-
After installation, remove protective fi lm from the outer surface of the lens.
0-10V DIMMABLE WIRING
Universal voltage driver permits operation at 120V thru 277V, 50 or 60 Hz.
0-10V control wires must be rated for 300V minimum. For 0-10V Dimming, follow
the wiring directions shown in Fig 2.
- Connect the black fi xture lead to the LINE supply lead.
- Connect the white fi xture lead to the COMMON supply lead.
- Connect the GROUND wire from fi xture to supply GROUND. Do NOT connect the GROUND of the dimming fi xture to the output.
- Connect the purple fi xture lead to the (V+) DIM lead.
- Connect the pink (or gray) fi xture lead to the (V-) DIM lead
SAFETY INSTRUCTIONS
WARNING: Risk of fi re or electric shock. Suitable for Damp locations.
WARNING: Suitable for 9/16” or 15/16” Flat Tee Grid in Insulated
Ceilings.
WARNING: Fixture to be independently supported to building structure.
CLEANING & MAINTENANCE
CAUTION: Be sure fi xture temperature is cool enough to touch. Do not clean or maintain while fi xture is energized.
- Clean polycarbonate lens with non-abrasive cleaning solution.
- Do not open the fi xture to clean the LED. Do not touch the LED
TROUBLESHOOTING
- Check that the line voltage at the fi xture is correct. Refer to wiring directions.
- Be sure the fi xture is grounded properly
WIRING
CAUTION: FOR BATTERY BACKUP FIXTURE. Voltage can be present in
BATTERY. To prevent high voltage from being present on output leads,
Inverter connector must be open. Do not join
BATTERY connector until installation is complete and AC power is supplied
to the emergency driver (Fig. 3).
NOTE: Make sure that the necessary branch circuit wiring is available. An
UNSWITCHED AC source of power is required. The emergency driver must be fed
from the same branch circuit as the LED driver.
CAUTION: Do not use any supply voltage other than 120-277V 50/60 HZ.
- Connect UNSWITCHED HOT fi xture lead to HOT AC supply line.
- If using an UNSWITCHED circuit, connect UNSWITCHED and SWITCHED lines together.
- If using a SWITCHED circuit, connect SWITCHED HOT AC fi xture lead to the external.
- Connect the pink (or gray) fi xture lead to the (V-) DIM lead.
- For 0-10V Dimming, connect DIM (+) and DIM (-) to the supply ground. Do not connect GROUND to the output leads.
- All unused leads must be capped and insulated.
- After installation is complete, supply AC power to the fi xture and connect the BATTERY.
- When power is on, the fi xture should be on and the Charging Indicator Light should illuminate to indicate the battery is charging.
- Once the BATTERY has charged for at least one hour, a short duration test may be performed by pressing the test button.
- After the battery has charged for 24 hours, a long duration test can be performed by shutting power to the fi xture.
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance.
OPERATION
- When AC power is applied, the charging indicator light is illuminated, indicating that the BATTERY is being charged.
- When power fails, the standby power automatically switches to emergency power (internal battery), operating at reduced illumination. The emergency driver supplies 8W of power for SWISH 2×2 and 16W of power for SWISH2x4 in standby power for a minimum of 90 minutes.
- When AC power is restored, the emergency driver automatically returns to charging mode.
MAINTENANCE
Although no routine maintenance is required to keep the emergency driver functional, it should be checked periodically to ensure that it is working. The following schedule is recommended
- Visually inspect the charging indicator light monthly. It should be illuminated.
- Test the emergency operation of the fi xture at 30-day intervals for a minimum of 30 seconds.
- Conduct a 90-minute discharge test once a year. Fixture would operate at reduced illumination for a minimum of 90 minutes.
TROUBLESHOOTING
- Is the fi xture grounded properly?
- If the charging indicator light does not illuminate after pressing the test button, check if battery is connected properly
RAB Lighting is committed to creating high-quality, aff ordable, well designed and energy-effi cient LED lighting and controls that make it easy for electricians to install and end users to save energy. We’d love to hear your comments. Please call the Marketing Department at 888-RAB-1000 or email: marketing@rablighting.com
Easy Answers
rablighting.com
Visit our website for product info
Tech Help Line
Call our experts: 888 722-1000
e-mail
Answered promptly – sales@rablighting.com
Free Lighting Layouts
© 2021 RAB LIGHTING Inc. Answered online or by request
RAB WARRANTY: RAB’s warranty is subject to all terms and conditions found at rablighting.com/warranty
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>