VONROC VC502AC Wet and Dry Vacuum Cleaner Instructions

VONROC VC502AC Wet and Dry Vacuum Cleaner Instructions

SAFETY INSTRUCTIONS

Read the enclosed safety warnings, the additional safety warnings and the instructions. Failure to follow the safety warnings and the instructions may result in electric shock, fire and/or serious injury. Save the safety warnings and the instructions for future reference.

The following symbols are used in the user manual or on the product:

Read the user manual.

Denotes risk of personal injury, loss of life or damage to the tool in case of nonobservance of the instructions in this manual.

Risk of electric shock.

Immediately remove the mains plug from the mains if the mains cable becomes damaged and during cleaning and maintenance.

Class II machine – Double insulation – You don’t need any earthed plug.

If the temperature of the material exceeds 40°C, there is a risk of fire.

Do not dispose of the product in unsuitable containers.

The product is in accordance with the applicable safety standards in the European directives.

SAFETY NOTES

DREN AGED FROM 8 YEARS AND ABOVE AND PERSONS WITH REDUCED PHYSICAL, SENSORY OR MENTAL CAPABILITIES OR LACK OF EXPERIENCE AND KNOWLEDGE IF THEY HAVE BEEN GIVEN SUPERVISION OR INSTRUCTION CONCERNING USE OF THE APPLIANCE IN A SAFE WAY AND UNDERSTAND THE HAZARDS INVOLVED. CHILDREN SHALL NOT PLAY WITH THE APPLIANCE. CLEANING AND USER MAIN- TENANCE SHALL  NOTBE MADE BY CHILDREN WITHOUT SUPERVISION. IF THE SUPPLY CORD IS DAMAGED, IT MUST BE REPLACED BY THE MANUFACTURER, ITS SERVICE AGENT OR SIMILARLY QUALIFIED PERSON IN ORDER TO AVOID A HAZARD. THE PLUG MUST BE REMOVED FROM THE SOCKETOUTLET BEFORE CLEANING OR MAINTAINING THE APPLIANCE.

1. Keep your work area clean: Cluttered work areas and workbenches are a source of injury.
2. The vacuum cleaner should be properly assembled before use.
3. Use only extension cords approved for outdoor use (when the vacuum is used outside) and make sure that they are always in good condition.
4. Protect the electric cables and, in particular, make sure that they are not crushed, pulled, or damaged by edges, sharp pieces, or moving parts; or damaged by corrosive liquids.
5. Do not use a damaged extension cord. Do not make any permanent or temporary repairs to the cable itself.
6. Do not use a vacuum cleaner that has a damaged electric cord. Have a new cable installed by an authorised service center.
7. Do not attach anything else to the socket, electric cords, or extension cord.
8. Before plugging your vacuum cleaner into the electrical outlet, make sure that the voltage and the outlet requirements match what is indicated on the label next to the cord.
9. Do not pull the device by the cord.
10. Your machine should always be turned off before unplugging it from the outlet or the extension cord.
11. Before leaving the device unsupervised (even for a brief time) turn it off and unplug it from the electrical outlet. This should also be done if there is a loss of power.
12. Do not underestimate its power. Always maintain a balanced and stable stance.
13. Keep children and pets away from the machine. When the machine is operating, everyone should stay at a safe distance.
14. The device should not be used by children or by persons who are not familiar with the device or who have not read this instruction manual.
15. The user of the device is responsible for the safety of others while using it.
16. The vacuum should only be used for its intended purposes.
17. Before performing any maintenance, adjustment or cleaning procedures on the vacuum cleaner, turn it off, unplug it from the electrical outlet, and wait for the motor to stop.
18. Be very careful when checking, cleaning, or performing maintenance on the device and wear thick work gloves to protect your hands.
19. Neither the security devices nor the electriccords should be modified or removed from the machine.
20. When using the machine, it should be kept steady and on a stable surface or supported by the body.
21. Only work in full daylight or with appropriate artificial light.
22. We recommend using some type of hearing protection for your ears.
23. If the machine vibrates abnormally, stop the motor and look for the cause immediately. Vibrations usually mean a problem.
24. The vacuum cleaner should be properly checked before each use. Do not use a machine that is not in perfect condition. If you notice a problem that could constitute a danger to the user, have the machine repaired before using it.
25. For safety reasons, replace worn or damaged parts. Use only manufacturer approved replacement parts. Parts from sources other than the manufacturer may not fit properly or may be dangerous or cause injuries. The power cord can only be replaced by specialized customer service centers.
26. Only use the vacuum cleaner in areas that are dry and protected from bad weather. Do not use it outside when it is raining.
27. Store the vacuum in a dry place, out of the reach of children.
28. Do not leave the power cord lying around once cleanup is done; someone could trip.
29. Take care when emptying extremely heavy tanks.
30. To avoid spontaneous combustion, empty the tank after every use.
31. Do not use this machine to vacuum up flammable or combustible liquids, such as gasoline, photocopier powder, or volatile substances; and do not use the machine in areas where these liquids are present. Do not vacuum up acids.
32. Do not vacuum up any materials that are toxic, cancer causing, combustible, or any other dangerous materials, such as asbestos, asbestos dust, arsenic, barium, beryllium, lead, pesticides, or any other substances hazardous to your health.
33. Extreme caution should be used when vacuuming up wood or charcoal ashes, soot, cement, plaster, or plasterboard dust. These particles are extremely fine and can pass through the filters affecting the motor’s performance or be blown into the air. If necessary, therefore we strongly recommend a cloth filter in combination with a dust collection bag when cleaning these types of materials.
34. Do not vacuum up anything that is burning or smoldering, such as cigarettes, cigarette butts, matches, or hot ashes.
35. Never vacuum up salt water; it may destroy the motor.

SAFETY WARNINGS SPECIFIC FOR BLOWING

a) Direct air discharge at work area only. Never at people or animals.
b) Risk of flying objects. Keep bystanders away from the work area.
c) Always wear safety goggles before using the blowing function.

Electrical safety

When using electric machines always observe the safety regulations applicable in your country to reduce the risk of fire, electric shock and personal injury. Read the following safety instructions and also the enclosed safety instructions.

Always check that the voltage of the power supply corresponds to the voltage on the rating plate label.

Class II machine – Double insulation – You don’t need any earthed plug

If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

MACHINE INFORMATION

Intended use

The vacuum cleaner is intended for domestic wet and dry vacuuming in, for example, the house, work room, car or garage. The vacuum cleaner is equipped with a blowing function. It can be used to blow dust and debris out of garages or of patios and driveways.

The device is not suitable for commercial or industrial use.

TECHNICAL SPECIFICATIONS

Diameter intake port ( 19 Fig. D)
****| Ø44mm
Recommended dust bag| VC802AA
Weight (incl. all accessories) approx.| 3.6kg

DESCRIPTION

The numbers in the text refer to the diagrams on

1. On/Off switch
2. Carrying handle
3. Vacuum port
4. Blowing port
5. Castor wheels
6. Locking clamp
7. Power cord storage
8. Tubes and nozzles storage
9. Container
10. Top section
11. Hose
12. Handle
13. Suction tubes
14. Floor nozzle
15. 2 in 1 nozzle
16. Dust collection bag
17. HEPA filter
18. Foam filter
19. Intake port
20. Float
21. Filter cage

ASSEMBLY

Before assembly, always switch off the machine and remove the mains plug from the mains

1. Press the 4 steering castors (5) on the container (9) and tighten the screws as shown in Fig. B. Make sure the steering castors (5) are securely fastened.

2. Assemble the vacuum port (3) on the container (9) and tighten the screws as shown in Fig. B.
   

3. Fit the filter. Ensure to mount the correct filter, depending on the application:

   • For dry vacuum cleaning, carefully slide the HEPA filter (17) over the filter cage (21) making sure the entire cage (21) is covered as shown in Fig. C-1.
     

   • For wet vacuum cleaning, carefully slide the foam filter (18) over the filter cage (21) making sure the entire cage (21) is covered as shown in Fig. C-2.
     

4. Place the top section (10) on the container (9) as shown in Fig. E.
   

5. Connect the suction hose (11).

   • For vacuuming ( Fig. F-1) , connect the suction hose (11) to the vacuum port (3).
     

   • For blowing ( Fig. F-2) , connect the suction hose (11) to the blowing port (4).
     

6. One or more suction tubes (13) can be fit to the handle (12) to extend it ( fig. A).
   

7. Connect the desired nozzle to the handle or suction tubes (13).

Floor nozzle (14)
The floor nozzle is designed for domestic wet and dry vacuuming in, for example, the house, work room, or garage.

2 in 1 nozzle (15)
The crevice nozzle is designed for domestic wet and dry vacuuming, edges and other areas that are difficult to access. The brush is designed to vacuuming solids from small areas

OPERATION

If the vacuum cleaner accidentally tips over, the shut-off float (20) mechanism may cover the motor vacuum port and stop the suction. If this happens, simply stand the vacuum upright and turn it off until the float (20) returns to its normal position.

Switching on (Fig. A):

Do not vacuum without a filter!

1. Fully unwind the suction hose (11).
2. Connect the mains plug.
3. Press the power switch (1) into the “ ON/1” position to start your vacuum cleaner.

Switching off (Fig. A):

Press the power switch (1) into the “ OFF/0” position to switch off your vacuum cleaner.

Dry vacuuming (Fig. A, C – F)

Clean the HEPA filter (17) regularly to maintain the suction power

To avoid the HEPA filter (17) becoming clogged, we recommend the additional use of a dust collection bag (16).

Fine dust, such as dust from cement, soot and plaster are too fine to be used with only the HEPA filter (17) and risk getting into the motor and damaging it. Therefore we strongly recommend a dust collection bag (16) when cleaning these types of materials.

Clogged dust collection bag (16) can burst – therefore make sure to replace the dust collection bag in a timely manner!

1. Switch off (1) the machine and remove the mains plug from the mains.

2. Unlock the locking clamp (6) and remove the top section (10).

3. Before vacuuming, remove all dirt and debris from the container (9).

4. Carefully slide HEPA filter (17) down over the filter cage (21) making sure the whole cage (21) is covered as shown in Fig. C-1.

5. For vacuuming with dust collection bag (16):

   • Hold the cardboard collar tightly and slide the rubber protective element as far as possible onto the intake port (19) as shown in Fig. D.
   • When everything is in place, unfold the bag (16) out and position it around the inside walls of the container (9).

6. Reattach the top section (10) again and lock the locking clamp (6).

7. Insert one end of the hose (11) into the vacuuming port (3). Fully unwind the suction hose (11).

8. Connect the mains plug.
   Press the power switch (1) into the “ ON/1” position to start your vacuum cleaner.

9. The machine now is ready to use for dry vacuum cleaning.

10. Press the power switch (1) into the “ OFF/0” position to switch off your vacuum cleaner.

Wet vacuuming (Fig. A, C, E – G)

The vacuum cleaner is equipped with a float (20). The suction power decreases when the maximum filling level is reached. Switch the vacuum cleaner off (1) immediately. Remove the plug from the socket and empty the container (9

Clean the float (20) at regular intervals, and check it for damage. Otherwise, its function can be impaired.

Never reach into the water to be suctioned up. Danger of electric shock.

Immediately switch (1) the machine off if foam forms or liquids escape!

Do not use a dust collection bag (16)!

1. Switch off (1) the machine and remove the mains plug from the mains.
2. Unlock the locking clamp (6) and remove the top section (10).
3. Before wet vacuuming, remove the dust collection bag (16), the HEPA filter (17) and remove all dirt and debris from the container (9).
4. Carefully slide foam filter (18) down over the filter cage (21) making sure the whole cage (21) is covered as shown in Fig. C-2.
5. Reattach the top section (10) again and lock the locking clamp (6).
6. Insert one end of the hose (11) into the vacuuming port (3). Fully unwind the suction hose (11).
7. Connect the mains plug.
8. Press the power switch (1) into the “ ON/1” position to start your vacuum cleaner.
9. The machine now is ready for wet vacuum cleaning.
10. Press the power switch (1) into the “ OFF/0” position to switch off your vacuum cleaner.
11. Raise the hose (11) so that the liquids drains into the container (9).
12. Empty the container (9) immediately after suction cleaning because it is not designed to store liquids

Blow function (Fig. A, E – F)

Operation without the use of a filter is recommended.

Remove all dirt and debris from the container (9) before you use the blow function.

Always wear safety goggles before using the blowing function.

Risk of flying objects. Keep bystanders away from the work area.

Your vacuum cleaner is equipped with a blowing function. It can be used to blow dust and debris out of garages or off patios and driveways.

1. Switch off (1) the machine and remove the mains plug from the mains.
2. Unlock the locking clamp (6) and remove the top section (10).
3. Before blowing, remove the dust collection bag (16), the filter (17, 18) and remove all dirt and debris from the container (9).
4. Reattach the top section (10) again and lock the locking clamp (6).
5. Insert one end of the hose (11) into the blowing port (4) on rear of machine. Fully unwind the suction hose (11).
6. Connect the mains plug
7. Press the power switch (1) into the “ ON/1” position to start your vacuum cleaner.
8. The machine is now ready for blowing dust and debris.
9. Press the power switch (1) into the “ OFF/0” position to switch off your vacuum cleaner

Finish operation (Fig. A)

1. Turn off (1) the machine and disconnect the mains plug.
2. Remove the top section (10) and empty the container (9).
3.  Clean the machine with a soft cloth.
4. Stow away the mains cable and accessory at the machine. Store the appliance in a dry room.

MAINTENANCE

Before cleaning and maintenance, always switch off the machine and remove the mains plug from the mains.

Clean the machine casings regularly with a soft cloth, preferably after each use. Make sure that the ventilation openings are free of dust and dirt. Remove very persistent dirt using a soft cloth moistened with soapsuds. Do  notuse any solvents such as gasoline, alcohol, ammonia, etc. Chemicals such as these will damage the synthetic components.

Filters (Fig. A)

For optimal performance it is recommended to regularly change the filters (17,18) depending on level of use.

1. Carefully remove HEPA (17) or foam (18) filter.
2. Use a mild soap and water solution to clean the filter and afterwards rinse with clean water.
3. Allow filter to air dry before installing and using again.
4. Re-install the filter.

Float and filter cage (Fig. G)

Clean the float (20) and filter cage (21) regularlywith a soft cloth, and check it for damage. Otherwise, its function can be impaired

ENVIRONMENT

Faulty and/or discarded electrical or electronic apparatus have to be collected at the appropriate recycling locations.

Only for EC countries
Do not dispose of power tools into domestic waste. According to the European Guideline 2012/19/ EC for Waste Electrical and Electronic Equipment and its implementation into national right, power tools that are no longer usable must be collected separately and disposed of in an environmentally friendly way.

WARRANTY

VONROC products are developed to the highest quality standards and are guaranteed free of defects in both materials and workmanship for the period lawfully stipulated starting from the date of original purchase. Should the product develop any failure during this period due to defective material and/or workmanship then contact VONROC directly.

The following circumstances are excluded from this guarantee:

• Repairs and or alterations have been made or attempted to the machine by unauthorized service centers;
• Normal wear and tear;
• The tool has been abused, misused or improperly maintained;
• Non-original spare parts have been used

This constitutes the sole warranty made by company either expressed or implied. There are no other warranties expressed or implied which extend beyond the face hereof, herein, including the implied warranties ofmerchantability and fitness for a particular purpose. In no event shall VONROC be  liable for any incidental or consequential damages.The dealers remedies shall be limited to repair or replacement of nonconforming units or parts.

The product and the user manual are subject to change. Specifications can be changed without further notice.

DECLARATION OF CONFORMITY

VC502AC – WET & DRY VACUUM CLEANER 

We declare under our sole responsibility that this product is in conformity with directive 2011/65/EU of the European parliament and of the council of 8 June on the restriction of the use of certain hazardous substances in electrical and electronic equipment is in conformity and accordance with the following standards and regulations:

60335-1: 2012+A11:2014+A13:2017
60335-2-2: 2010+A11:2012+A1:2013
62233:2008
55014-1:2017
55014-2:2015,
61000-3-2: 2014
61000-3-3:2013, 2014/35
Zwolle, 01-11-2021

H.G.F Rosberg CEO

VONROC
Lingenstraat 6
8028 PM Zwolle
The Netherlands

©2021 VONROC
WWW.VONROC.COM
2111-05

References

• VONROC Gereedschap & Tuin artikelen

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>