VONROC EH518AC Electric PTC Fan Heater Instruction Manual

VONROC EH518AC Electric PTC Fan Heater Instruction

SAFETY INSTRUCTIONS

Read the enclosed safety warnings, the additional safety warnings and the instructions. Failure to follow the safety warnings and the instructions may result in electric shock, fire and/or serious injury. Save the safety warnings and the instructions for future reference. The following symbols are used in the user manual or on the product

• Read the user manual.
• Denotes risk of personal injury, loss of life or damage to the tool in case of non-observance of the instructions in this manual.
• Denotes risk of electrical shock. Class II machine – Double insulation – You don’t need any earthed plug.
• Important! WARNING: In order to avoid overheating, do not cover the heater.
• Do not dispose of the product in unsuitable containers.
• The product is in accordance with the applicable safety standards in the European directives.

GENERAL SAFETY WARNINGS

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. Children of less than 3 years should be kept away unless continuously supervised. Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance

CAUTION — Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.

ADDITIONAL SAFETY WARNINGS FOR ELECTRIC HEATER

• Children should be kept away unless continuously supervised to ensure that they do not play with the heater.
• Children shall not plug in, position, operate, regulate and clean the appliance or perform user maintenance.
• CAUTION-some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.
• The heater is not suitable for use outdoors in damp weather, in bathrooms or in other wet or damp environments.
• Please note that the heater can become very hot and should, therefore, be placed at a safe distance from flammable object such as furniture, curtains and similar.
• Use handle when moving this heater.
• Do not move the heater when it is heated. Allow the product to thoroughly cool before handling it.
• Do not cover the heater.
• The heater must not be located immediately below a socket outlet.
• Do not connect the heater using an on/off timer or other equipment which can automatically switch the device on.
• The heater must not be placed/used in rooms where flammable liquids or gases are used or stored.
• If an extension cord is used, it must be as short as possible and always be fully extended.
• You must not connect other appliances to the same mains socket as the heater.
• Do not use the heater in immediate surroundings of a bath, a shower or a swimming pool.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• Make sure the heater is always under surveillance and keep children and animals away from it.
• Do not place/use the heater on moving vehicles or some where easy to be tripped over.
• When the heater is not used for a long time, unplug the heater form its means. Pull the plug straight out, never remove the plug by pulling the cord.
• Keep the heater far from curtain or places where the air inlet van easily be blocked.
• The power coupler is waterproof when not in use. In order to prevent possible electric shock or leakage current, never use the heater with wet hand or operate the heater when there is water on the power cord.
• Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact your local government for information regarding the collection systems available. If electrical appliance are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being.

Warning! Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own, unless constant supervision is provided.
Warning! To reduce the risk of fire, keep textiles, curtains, or any other flammable material a minimum distance of 1 m from the air outlet

Electrical safety
When using electric machines always observe the safety regulations applicable in your country to reduce the risk of fire, electric shock and personal injury. Read the following safety instructions and also the enclosed safety instructions. Always check that the voltage of the power supply corresponds to the voltage on the rating plate label If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

Using extension cables
Only use an approved extension cable suitable for the power input of the machine. The minimum conductor size is 1.5 mm2. When using a cable reel always unwind the reel completely.

PRODUCT INFORMATION

Intended use
The electrical heater is intended for indoor, non-commercial, household use for temporarily heating residential rooms. Do not use the product for any other purpose. The heater can be used in enclosed rooms in a free standing position for room heating. The heater may only be used completely mounted and standing vertically on a stable surface. It incorporates a thermostat and a self-resetting thermal cut-out to control the heating element and therefore the temperature.

TECHNICAL SPECIFICATIONS

DESCRIPTION
The numbers in the text refer to the diagrams on page 2-3.

1. Heater

2. Control panel
   A. On/off button
   B.Temperature / timer increase button
   C. Temperature / timer decrease button
   D. Mode / timer button

3. Display
   A. Temperature
   B. Mode indicator

4. Main switch

5. Air outlet grille

6. Handle

7. Air inlet

8. Tip-over switch

OPERATING

Check the device for damage before use and only use in good working condition. When using the heater for the first time, you may notice a slight emission of smoke. This is quite normal and it stops after a short time. The heating element is made of stainless steel and was coated with protection oil by production. The smoke is caused by the left oil when heated.

Placing the electric heater

• Place the heater upright on a firm and a level surface.
• Keep a minimum distance of 1 m between the front of the housing and walls and 30 cm from all other housing surface areas. Keep away from wet environments.

Warning! Make sure to place the heater in a safe spot, so you cannot easily trip over the machine and cable. Make sure to place the heater where it cannot fall down/ of.

Starting the electric heater (Fig A, B)

• Plug in the cable to the mains power outlet.
• Turn the main switch (4) on.
• Press the on/off button (2A) to start the heater. The last setting has been saved. Press the mode button (2D) to change the heating mode. – Fan: the mode indicator (3B) will show one dot. – Low heating mode – 1000W: the mode indicator (3B) will show two dots. – High heating mode – 2000W: the mode indicator (3B) will show three dots.

Adjusting the temperature (Fig. B)

• By default, the ambient temperature is shown on the display (3).
• The last setting has been saved. The temperature can be set between 16oC and 37oC.
• Set the temperature as desired by press the temperature / timer increase or decrease button (2B, 2C).
• The target temperature will keep flashing for 5 seconds after the last button press, then the display will show the ambient temperature.
• The display dims after one minute of inactivity.

Constant room temperature
The heater starts and stops automatically to keep the room temperature constant. Once the ambient temperature in the room reaches the desired target temperature, the heating element will be in standby mode. Once the ambient temperature starts to decrease, the heating element will be switched on again.

Set the timer
The timer can be set between 1 hour and 9 hours. Hold on the mode button (2D) for 5 seconds. The display (3) shows flashing the duration currently set for 5 seconds. Press the temperature / timer increase and decrease button (2B, 2C) to set the timer with 1 hour intervals. The display (3) alternately shows the set timer and ambient temperature. Without a timer there is no limit.

Tip-over switch (8)
This heater has an mechanical tip-over protection. This protection ensures when the heater is not placed upright on a firm and level surface or when the heater tip over, the system will automatically shut the heater off. If this occurs, put the heater on a firm and level surface and start the heater again.

Automatic Overheat Safety Control
This heater is equipped with safety internal heat limiting thermostat and overheat protection circuit. When a potential overheat temperature is reached, the system will automatically shut the heater off. If this occurs, the heater can only resume after resetting it. To reset the heater: Unplug the heater and wait at least 30 minutes to cool down before restarting the heater.

Stopping the electric heater (Fig. A)
Let the machine cool down before turning off by using the ventilation function.

• Press the on/off button (2A).
• The fan mode will start and will cool down the heater for a few minutes.
• Turn the main switch (4) off.
• Pull the plug out of the mains power outlet

Storing the electric heater

• Always let the heater cool down completely before storing the machine.
• Never wrap the cable around the heater

Warning! Never store the machine in a wet or dusty environment

MAINTENANCE

Before cleaning and maintenance, always switch off the machine and remove the mains plug from the mains.

Cleaning Let the machine cool down completely before cleaning.

• Clean the heater with a (lightly damp) cloth, brush or vacuum cleaner.
• In order to protect the enclosure, don’t splash water onto the heater, and never use a solvent like gasoline, isoamyl acetate, toluene, etc. to clean the heater.
• Clean the air inlet and outlet (5, 7) regularly with a vacuum cleaner.
• When you store the heater, let it cool down first and, keep it dry.

Trouble shooting
In case the electric heater does not work well, we give you subjoined some possible causes and their solutions.

The heater does not operate, even when it

is plugged in and the switch, thermostat are

switched on.

| The plug is loose, bad

connection

| Pull out the plug, check the connection of the plug and

socket. Then connect again.

No power in socket outlet

|

Insert the plug in a proper socket

The heating element glowing

| The input voltage is too

high or too low

| Use power supply according to the rating on the label

The air inlet grill is blocked

| Keep the heater far way from articles like curtain, plastic bag, paper and other things which can cover the inlet or can be

easily cover on the air inlet

The appliance didn’t heat up, only ventilator worked

| The switch was not put at

heating setting

|

Turn the switch to heat setting

The thermostat operated

| Turn the thermostat and listen if there is open/close voice. If there is no click and the thermostat

is not damaged, the heater will automatic switch on when the

appliance cooled down

The self-retting cut-out operated

| Turn the heater off and inspect the blockage of inlet or outlet. Disconnect the plug and wait at least 10 minutes for the

protection system to reset before

attempting to restart the heater.

Abnormal noise

| The appliance is not stands

upright

|

Put the heater on a level surface

ENVIRONMENT

Faulty and/or discarded electrical or electronic apparatus have to be collected at the appropriate recycling locations.

Only for EC countries
Do not dispose of power tools into domestic waste. According to the European Guideline 2012/19/EU for Waste Electrical and Electronic Equipment and its implementation into national right, power tools that are no longer usable must be collected separately and disposed of in an environmentally friendly way.

WARRANTY

VONROC products are developed to the highest quality standards and are guaranteed free of defects in both materials and workmanship for the period lawfully stipulated starting from the date of original purchase. Should the product develop any failure during this period due to defective material and/or workmanship then contact VONROC directly. The following circumstances are excluded from this guarantee:

• Repairs and or alterations have been made or attempted to the machine by unauthorized service centers;
• Normal wear and tear;
• The tool has been abused, misused or improperly maintained;
• Non-original spare parts have been used.

This constitutes the sole warranty made by company either expressed or implied. There are no other warranties expressed or implied which extend beyond the face hereof, herein, including the implied warranties of merchantability and fitness for a particular purpose. In no event shall VONROC be liable for any incidental or consequential damages. The dealers remedies shall be limited to repair or replacement of nonconforming units or parts. The product and the user manual are subject to change. Specifications can be changed without further notice.

Model identifier(s): EH518AC

Item| Symbol| Value| Unit| Item| Unit
Heat output| Type of heat input, for electric storage local space heaters only (select one)
Nominal heat output| Pnom| 2.0| kW| manual heat charge control, with integrated thermostat| No
Minimum heat output (indicative)| Pmin| 1.0| kW| manual heat charge control with room and/ or outdoor temperature feedback| No
Maximum continuous heat output| Pmax,c| 2.0| kW| electronic heat charge control with room and/or outdoor temperature feedback| No
Auxiliary electricity consumption|  | fan assisted heat output| No
At nominal heat output| elmax| 0.000| kW| Type of heat output/room temperature control (select one)
At minimum heat output| elmin| 0.000| kW| single stage heat output and no room tem- perature control| No
In standby mode| elSB| 0.001| kW| Two or more manual stages, no room tem- perature control| No
 |  |  |  | with mechanic thermostat room tempera- ture control| No
 |  |  |  | with electronic room temperature control| Yes
 |  |  |  | electronic room temperature control plus day timer| No
 |  |  |  | electronic room temperature control plus week timer| No
 |  |  |  | Other control options (multiple selections possible)
 |  |  |  | room temperature control, with presence detection| No
 |  |  |  | room temperature control, with open win- dow detection| No
 |  |  |  | with distance control option| No
 |  |  |  | with adaptive start control| No
 |  |  |  | with working time limitation| No
 |  |  |  | with black bulb sensor| No
Contact details| VONROC • Lingenstraat 6 • 8028 PM • Zwolle • The Netherlands

DECLARATION OF CONFORMITY EH518AC – ELECTRIC PTC FAN HEATER

We declare under our sole responsibility that this product is in conformity with directive 2011/65/EU of the European parliament and of the council of 8 June on the restriction of the use of certain hazardous substances in electrical and electronic equipment is in conformity and accordance with the following standards and regulations

©2022 VONROC WWW.VONROC.COM

References

• VONROC Gereedschap & Tuin artikelen

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>