DMP LT-2742 XR Control Panel User Manual

DMP LT-2742 XR Control Panel User Manual

IDENTIFY PANEL COMPONENTS

1. Identify the following panel components using the panels in front of you, or the on-screen photo of the XR.

• Reset header
• Programming header
• Outputs
• AC Power terminals
• Cellular pins
• 1100 Series receiver connection
• On-board zone terminals
• Network connection
• EXP header

POWER UP THE CONTROL PANEL

1. Connect AC power to terminals 1 & 2
   Transformer type: 16.5VAC 50VA

2. Connect battery backup to terminals 3 & 4

3. Connect alarm bell to terminals 5 & 6
   Normal 12VDC is supplied to terminal 5, terminal 6 is ground reference
   1/2 W 1K Ohm resistor should be added across the bell circuit for supervision

ENTER PANEL PROGRAMMER

1. Reset the panel using the RESET JUMPER
2. Enter 6653 (PROG) and press CMD
3. Press CMD to navigate through the panel programmer menus:
   •  Initialization
   •  Communication
   •  Network Options
   •  Device Setup
   •  Remote Options
   •  System Reports
   •  System Options
   •  Bell Options
   •  Output Options
   •  Output Information
   •  Output Groups
   •  Status List
   •  Menu Display
   •  PC Log Reports •  Area Information
   •  Zone Information
   •  Stop
   •  Set Lockout Code
   •  Feature Upgrade

ADJUST COMMUNICATION TYPE

1. Navigate to COMMUNICATION and press a top-row select area

2. Press a top-row select area to clear the default ACCOUNT NUMBER

3. Enter in an ACCOUNT NUMBER

4. Press CMD to navigate to PATH

5. Press 1 to program PATH 1

6. Press a top-row select area to display the COMMUNICATION types

7. Select NET

8. Press CMD to navigate to CHECKIN

9. Press a top-row select area and select YES

10. Press a top-row select area and enter your CHECKIN MINS

11. Press a top-row select area and enter your FAIL MINS

12. Press CMD to navigate to RECEIVER IP

13. Press a top-row select area and enter in the DMP Tech Support receiver IP Address
    ê 209.248.148.051 (Port 2001)

14. Press CMD to navigate to PATH

15. Press 2 to program PATH 2

16. Press a top-row select area to display the
    COMMUNICATION TYPES

17. Select CELL

18. Press CMD to navigate to CHECKIN

19. Press a top-row select area and select YES

20. Press a top-row select area and enter your CHECKIN MINS

21. Press a top-row select area and enter your FAIL MINS

22. Press CMD to navigate to RECEIVER IP

23. Press a top-row select area and enter in the DMP Tech Support receiver IP Address
    ê 209.248.148.051 (Port 2001)

24. Press CMD to navigate to ADVANCED

25. Press the fourth top-row select area

26. Press CMD to navigate to SUB CODE

27. Press a top-row select area and select YES

28. Press CMD to exit COMMUNICATION

ADD AN ANNUNCIATOR

1. Navigate to DEVICE SETUP and press a top-row select area

2. Enter a DEVICE NUMBER and press CMD
   The valid range for an XR150 panel is 1-8, XR550 is 1-16

3. Press a top-row select area and enter a DEVICE NAME

4. Press CMD to confirm the DEVICE TYPE

5. Press CMD to exit DEVICE SETUP

ADJUST AN ANNUNCIATOR ADDRESS

1. Press and hold the BACK ARROW and CMD for 2 seconds
2. Enter 3577 (INST) and CMD
3. Select KEYPAD OPTIONS (KPD OPT)
4. Press a top-row select area or key to change the keypad address
5. Press CMD to exit KEYPAD OPTIONS
6. Select STOP to save keypad programming

CONFIGURE SYSTEM OPTIONS

1. Navigate to SYSTEM OPTIONS and press a top-row select area
2. Press CMD to navigate to HOURS FROM GMT
3. Press a top-row select area, enter in the hours from GMT for your location and press CMD
4. Using CMD, navigate to HOUSE CODE
5. Press a top-row select area and enter a house code from 1-50 and press CMD
6. Press CMD to navigate to SEND 16 CHAR NAMES
7. Press the third top-row select area to select NO
8. Press CMD to exit SYSTEM OPTIONS

ADD AN AREA

1. Navigate to AREA INFORMATION and press a toprow select area
2. Press CMD to navigate to AREA NO
3. Enter an AREA NUMBER and press CMD
4. Press a top-row select area to clear any text and enter in FIRE
5. Exit AREA INFORMATION and navigate to STOP to save changes

ADD A WIRELESS FIRE ZONE

Dealer Admin
6. Select the CUSTOMERS tab on the side menu
7. Select a SYSTEM to open the System Information page for that system
8. Select PROGRAMMING
9. Select ZONE INFORMATION
10. Select ADD ZONE
11. Enter a ZONE NUMBER and ZONE NAME
ê Valid wireless zone numbers are 500-599 on an XR150 and 500-999 on an XR550
12. Select the Zone Type drop-down menu and select FIRE
13. Toggle on DMP WIRELESS
14. Enter a SERIAL NUMBER
15. Select SEND ALL CHANGES

Keypad

1. Reset the panel using the RESET JUMPER

2. Enter 6653 (PROG) and press CMD

3. Press CMD to navigate to Zone Information and press a top-row select key

4. Enter a ZONE NUMBER and press CMD
   ê Valid wireless zone numbers are 500-599 on an XR150 and 500-999 on an XR550

5. Press a top-row select key and enter a ZONE NAME

6. Press a top-row select key and select FI (FIRE)

7. Press a top-row select key and enter the FIRE BELL OUTPUT

8. At the NEXT ZONE? NO YES prompt, select NO to program a wireless zone

9. At the DMP WIRELESS? NO YES prompt, select YES and press CMD

10. Enter a SERIAL NUMBER and press CMD to navigate to the NEXT ZONE? NO YES prompt

11. Navigate to STOP to save programming

ADD A WIRED FIRE ZONE

Dealer Admin

1. Select the CUSTOMERS tab on the side menu

2. Select a SYSTEM to open the System Information page for that system

3. Select PROGRAMMING

4. Select ZONE INFORMATION

5. Select ADD ZONE

6. Enter a ZONE NUMBER and ZONE NAME
   ê Valid wireless zone numbers are 500-599 on an XR150 and 500-999 on an XR550

7. Select the Zone Type drop-down menu and select FIRE

8. Select SEND ALL CHANGES

Keypad

1. Reset the panel using the RESET JUMPER

2. Enter 6653 (PROG) and press CMD

3. Press CMD to navigate to Zone Information and press a top-row select key

4. Enter a ZONE NUMBER and press CMD

5. Press a top-row select key and enter a ZONE NAME

6. Press a top-row select key and select FI (FIRE)
   Press a top-row select key and enter the FIRE BELL OUTPUT

7. At the NEXT ZONE? NO YES prompt, select YES

8. Navigate to STOP to save programming

STANDARD WALK TEST

1. At the keypad, enter 8144 (WALK) to enter the WALK TEST menu
2. Select STD to begin the standard walk test
3. Trip wired and wireless zones to complete the standard walk test

WIRELESS CHECK-IN TEST

1. At the keypad, enter 8144 (WALK)
2. Select WLS to begin the wireless check-in test

FIRE DRILL

1. Enter the USER MENU and navigate to the FIRE DRILL? NO YES prompt
2. Press a top-row select key to display the SURE? YES NO prompt
3. Press the top-row select key underneath YES to start the fire drill
4. To end the fire drill either:
   •  Enter your USER CODE and press CMD
   •  Enter the USER MENU and navigate to the
   ALARM SILENCE? prompt and press a top-row select key

DIAGNOSTIC MENU

1. At the keypad, enter 2313 (DIAG) to enter the DIAGNOSTIC MENU

2. Press CMD until the keypad displays COMM STATUS and press a top row select area

3. Press 1 to test COMMUNICATION PATH 1

4. When the signal strength is displayed, select YES to continue the test
   •  Cellular Communcation Only

5. Press CMD and select STOP to exit the DIAGNOSTIC MENU

CREATE A PROFILE

1. At the keypad, press CMD until the USER MENU? prompt displays

2. Select YES and enter 99+CMD to enter the USER MENU

3. Using CMD, navigate to PROFILES? and press a toprow select area

4. Select ADD and enter 11 to create Profile 11

5. Press a top row area to name the profile ACCESS

6. Assign ARM/DISARM AREA 2 and press CMD

7. Assign ACCESS AREA 2 and press CMD

8. Press CMD until DISARM? displays and select YES

9. Navigate to DOOR ACCESS and confirm it is set to YES

10. Navigate to FIRST ACCESS SCHEDULE and press the third select area to enter the schedule number
    for the access schedule

11. LIST will show the schedule names

12. Press CMD until PROFILE 11 ADDED is displayed

13. Create another profile named MANAGEMENT using Profile 12

The instructor will provide settings for this profile

ADD A USER CODE WITH PIN
14. Enter the USER MENU and navigate to the USER CODES? prompt
15. Press a top-row select area to add a USER CODE
16. Select ADD
17. Select the USER NUMBER and press CMD
•  The fourth top row select area will display the lowest available user number
18. Enter in a 5-digit user code and press CMD
19. Press a top-row select area to add a USER NAME and press CMD
20. Press a top row select area enter 12 to assign PROFILE 12 to this user
•  LIST will display the profile names
21. Press CMD until USER ADDED displays

PROGRAM A RELAY

1. Remove all power from the panel

2. Plug a MODEL 305 relay into the socket for OUTPUT 1
   ê Make sure the relay is oriented correctly

3. Connect the MODEL 431 harness to the header between the output sockets

4. Connect the POSITIVE leg of the LED to the RED terminal on the panel

5. Connect the other leg of the LED to the second ORANGE wire on the harness

6. Connect the second GRAY wire to the BLACK terminal on the panel

7. Power the panel back up

8. Enter the Programmer by entering 6653 (PROG) at the keypad

9. Navigate to ZONE INFORMATION and press a toprow select area

10. Navigate to settings for ZONE 1

11. Program ZONE 1 as a NIGHT type zone in AREA 1

12. At the NEXT ZN? prompt, select NO

13. Navigate to DISARMED SHORT and press CMD until OUTPUT NO is displayed

14. Press a select area to set the output to 1.

15. Set the output action to FOLLOW

16. Navigate to STOP to save changes and exit the Programmer

17. Press the button to trip ZONE 1.
    •  Notice the output state follows the zone state.

QUESTIONS
What else would you like to learn about Fire?

NOTES:

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>