EXPLORE SCIENTIFIC CF600 Refractor Telescope Instruction Manual
- June 10, 2024
- EXPLORE SCIENTIFIC
Table of Contents
SCIENTIFIC CF600 Refractor Telescope
Instruction Manual
CF600 Refractor Telescope
WARNING:
SUN HAZARD — Never look directly at the sun with this device.
WARNING:
CHOKING HAZARD — Small parts.
Not for children under 3 years.
X1
INCLUDED
WARNING:
Contains button or coin cell battery.
Hazardous if swallowed — see instructions.
WARNING:
The lens contains lead that may be harmful.
Wash hands after touching.
WARNING:
This product can expose you to chemicals including lead, which is known to the
State of California to cause cancer and birth defects or other reproductive
harm.
For more information go to
www.P65Warnings.ca.gov.
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW THE INSTRUCTIONS BEFORE USE.
KEEP THESE INSTRUCTIONS FOR LATER USE.
-
SUN WARNING: WARNING: NEVER ATTEMPT TO OBSERVE THE SUN WITH THIS DEVICE! OBSERVING THE SUN – EVEN FOR A MOMENT – WILL CAUSE INSTANT AND IRREVERSIBLE DAMAGE TO YOUR EYE OR EVEN BLINDNESS. EYE DAMAGE IS OFTEN PAINLESS, SO THERE IS NO WARNING TO THE OBSERVER THAT THE DAMAGE HAS OCCURRED UNTIL IT IS TOO LATE. DO NOT POINT THE DEVICE AT OR NEAR THE SUN. DO NOT LOOK THROUGH THE DEVICE AS IT IS MOVING. CHILDREN SHOULD ALWAYS HAVE ADULT SUPERVISION WHILE OBSERVING.
-
RESPECT PRIVACY: WHEN USING THIS DEVICE, RESPECT THE PRIVACY OF OTHER PEOPLE. FOR EXAMPLE, DO NOT USE IT TO LOOK INTO PEOPLE’S HOMES.
-
CHOKING HAZARD: CHILDREN SHOULD ONLY USE DEVICE UNDER ADULT SUPERVISION. KEEP PACKAGING MATERIALS LIKE PLASTIC BAGS AND RUBBER BANDS OUT OF THE REACH OF CHILDREN AS THESE MATERIALS POSE A CHOKING HAZARD.
-
RISK OF BLINDNESS: NEVER USE THIS DEVICE TO LOOK DIRECTLY AT THE SUN OR IN THE DIRECT PROXIMITY OF THE SUN. DOING SO MAY RESULT IN A PERMANENT LOSS OF VISION.
-
RISK OF FIRE: DO NOT PLACE DEVICE, PARTICULARLY THE LENSES, IN DIRECT SUNLIGHT. THE CONCENTRATION OF LIGHT RAYS COULD CAUSE A FIRE.
-
DO NOT DISASSEMBLE THIS DEVICE: IN THE EVENT OF A DEFECT, PLEASE CONTACT YOUR DEALER. THE DEALER WILL CONTACT THE CUSTOMER SERVICE DEPARTMENT AND CAN SEND THE DEVICE IN TO BE REPAIRED IF NECESSARY.
-
DO NOT SUBJECT THE DEVICE TO TEMPERATURES EXCEEDING 60 °C (140 °F).
-
DISPOSAL: KEEP PACKAGING MATERIALS, LIKE PLASTIC BAGS AND RUBBER BANDS, AWAY FROM CHILDREN AS THEY POSE A RISK OF SUFFOCATION. DISPOSE OF PACKAGING MATERIALS AS LEGALLY REQUIRED. CONSULT THE LOCAL AUTHORITY ON THE MATTER IF NECESSARY AND RECYCLE MATERIALS WHEN POSSIBLE.
-
THE WEEE SYMBOL IF PRESENT INDICATES THAT THIS ITEM CONTAINS ELECTRICAL OR ELECTRONIC COMPONENTS WHICH MUST BE COLLECTED AND DISPOSED OF SEPARATELY.
-
NEVER DISPOSE OF ELECTRICAL OR ELECTRONIC WASTE IN GENERAL MUNICIPAL WASTE. COLLECT AND DISPOSE OF SUCH WASTE SEPARATELY.
-
MAKE USE OF THE RETURN AND COLLECTION SYSTEMS AVAILABLE TO YOU, OR YOUR LOCAL RECYCLING PROGRAM.
CONTACT YOUR LOCAL AUTHORITY OR PLACE OF PURCHASE TO FIND OUT WHAT SCHEMES ARE AVAILABLE. -
ELECTRICAL AND ELECTRONIC EQUIPMENT CONTAINS HAZARDOUS SUBSTANCES WHICH, WHEN DISPOSED OF INCORRECTLY, MAY LEAK INTO THE GROUND. THIS CAN CONTRIBUTE TO SOIL AND WATER POLLUTION WHICH IS HAZARDOUS TO HUMAN HEALTH, AND ENDANGER WILDLIFE.
-
IT IS ESSENTIAL THAT CONSUMERS LOOK TO RE-USE OR RECYCLE ELECTRICAL OR ELECTRONIC WASTE TO AVOID IT GOING TO LANDFILL SITES OR INCINERATION WITHOUT TREATMENT.
BUTTON/COIN BATTERY WARNING: THIS PRODUCT CONTAINS A BUTTON OR COIN CELL BATTERY. A SWALLOWED BUTTON OR COIN CELL BATTERY CAN CAUSE INTERNAL CHEMICAL BURNS IN AS LITTLE AS TWO HOURS AND LEAD TO DEATH. DISPOSE OF USED BATTERIES IMMEDIATELY. KEEP NEW AND USED BATTERIES AWAY FROM CHILDREN. IF YOU THINK BATTERIES MIGHT HAVE BEEN SWALLOWED OR PLACED INSIDE ANY PART OF THE BODY, SEEK IMMEDIATE MEDICAL ATTENTION.
Parts Overview
- 50 mm Objective Lens
- Pan Tilt Mount
- Tripod with accessory tray
- Optical Tube Assembly (OTA) with Dew Shield
- Focus Wheel
- Diagonal
- 1.25” Eyepieces (PL9.7 mm and PL26 mm)
- Red Dot Viewfinder
- Panhandle
- Focuser
Available Downloads Visit: www.esmanuals.com
How To Set Up
Note: We recommend assembling your telescope for the first time in the daylight or in a lit room so that you can familiarize yourself with assembly steps and all components.
- Open the tripod until the tripod spreaders are fully extended. Put the accessory tray in place and turn it clockwise until stable. To set the tripod height, turn the pressure fitting on each leg counterclockwise until loose. Extend or retract the leg to the desired setting, then tighten the pressure fitting until snug.
- Thread the panhandle clockwise onto the tripod head.
- Set the optical tube assembly on the tripod head and align the tab on the bottom of the telescope tube with the slot in the tripod head. Thread the front tension wheel until snug, then tighten the side tension thumbscrew. Be careful not to over-tighten either screw.
- Insert the diagonal into the focuser and secure it by tightening the thumbscrews.
- Slide the red dot viewfinder into the finder bracket that is already mounted on the telescope tube.
- Place your chosen eyepiece into the diagonal. We recommend starting with the 26 mm because it will provide the widest field of view.
Using/Aligning the Red Dot Viewfinder:
The viewfinder is powered by a CR-2032 battery that is included. Before using
the viewfinder for the first time, remember to remove the plastic insulator
that is blocking the battery from connecting.
When it is time to replace the battery, remove the battery cap by loosening
the set screw. Take out the old battery and slide a new battery in place with
the positive side showing. Replace the cap, and tighten the set screw.
For The Viewfinder To Be Effective, It Must Be Aligned. (Fig 1; 1-3)
- Insert the 26mm eyepiece into the diagonal and power on the viewfinder by sliding the switch on its right side to an “On” position.
- Point the telescope at an easy to identify target like a tree or telephone pole that is approximately 200 yards away. Center the object in the eyepiece. Lock the telescope into place by tightening the panhandle.
- Without moving the telescope, position the red dot using the two adjustment screws so that it shares the same view as the one in your eyepiece. The front screw will move the viewfinder up and down, and the other will move it side to side. Your viewfinder is now aligned.
Note: To preserve battery life, don’t forget to turn off the viewfinder
after use.
The Red Dot Viewfinder is powered by a battery type CR-2032 (3V); if a
replacement is necessary, remove the cap (Fig. 1) by unscrewing the set screw
(Fig. 2) slide the battery towards the front. Slide the new battery in with
the positive (+) side showing. Replace the cap and tighten the set screw (Fig.
2). Using Your Telescope:
After you have aligned your viewfinder, you are ready to start observing! Put
the 26mm eyepiece into the focuser to get the widest field of view. This wider
field of view will make it easier to locate and track objects. Use the
panhandle to move the scope up, down and side to side until your target comes
into view in the eyepiece. It is important to remember that the rotation of
the Earth means objects will move out of your eyepiece fairly quickly. Once
you have found and focused on your desired target, you can track it as it
journeys across the night sky using the panhandle.
To get a closer look at an object, take out the 26mm eyepiece and replace it
with the 9.7mm eyepiece. This will increase the magnification from 23x to 61x.
Focal Length | Eyepiece | Magnification |
---|---|---|
600mm | 26mm | 23x |
600mm | 9.7mm | 61x |
Note: Terrestrial objects will appear reversed due to the optical setup.
This rotation is perfectly normal for a refractor using a standard diagonal,
and it will not affect astronomical viewing.
Cleaning:
Your telescope is a precision optical device and keeping the optics free of
dust and dirt is crucial for optimal performance. To clean the lenses
(objective and eyepiece) use only a photo-grade soft brush or a lint-free
cloth, like a microfiber cloth. Do not press down too hard while cleaning, as
this might scratch the lens. If necessary, the cleaning cloth can be moistened
with an optical glass cleaning fluid and the lens wiped clean using very
little pressure. The eyepiece is NOT waterproof so do not spray fluids
directly onto the glass or dip it in water. Never use harsh detergents! After
you have finished cleaning an eyepiece, allow it to fully dry before storing.
Make sure your telescope is always protected against dust and dirt. After use,
leave it in a warm room to dry off before storing.
Troubleshooting Guide:
Problem | Solution |
---|---|
No picture | Remove dust protection cap. |
Blurred picture | Adjust focus using focus wheel. |
No focus possible | Wait for temperature to balance out. |
Bad quality | Never observe through a glass surface such as a window. |
Viewing object visible in the finder, but not through the telescope | Align |
finder to telescope (see instructions)
Observing Tips:
Star hopping
Star hopping is a technique used by amateur astronomers to navigate the night
sky. By using easily recognizable constellations and asterisms as a guide, an
observer can locate stars and other objects.
For example, Polaris, which is commonly referred to as The North Star, can be
located quickly using star hopping. First, find the Big Dipper asterism in the
Ursa Major constellation. The popular pattern is defined by seven stars, and
the two stars on the front edge of the Big Dipper’s “bowl” are Merak and
Dubhe.
Next, draw an imaginary line from the bottom star (Merak) on this front edge
through the top star (Dubhe) on the front edge. Follow the line to the first
bright star you see. That should be Polaris. Finally, to verify your finding,
locate the Little Dipper asterism. Polaris is the anchor star at the end of
the Little Dipper’s “handle.” Note: The positioning
of the Big Dipper in relation to the Little Dipper does not change, but the
orientation of both in the night sky will rotate throughout the year due to
the motion of the Earth.
Possible Objects for Observation:
What you can observe at any one time in your telescope depends on several
factors beyond aperture and magnification. These factors include location,
date, time and sky conditions. The following are all objects that can be seen
with the unaided eye and/or binoculars. Your telescope can enhance views of
any of these objects if the observing conditions are right.
Image credit: Howard Eskildsen
The Moon:
Diameter: 3,476 km
Distance: Approximately 384,401 km
The Moon is the Earth’s only natural satellite, and it is the second brightest
object in the sky (after the Sun). Although it is our closest neighbor, a lot
of people have never really taken a good long like at the Moon. With your
telescope, you should be able to see several interesting lunar features. These
include lunar maria, which appear as vast plains, and some of the larger
craters. The best views will be found along the terminator, which is the edge
where the visible and shadowed portions of the Moon meet.
Note: Images are for illustration purposes only. Quality of your image
may very depending upon atmospheric conditions and location. Orion Nebula(M42):
Right ascension: 05: 35.4 (hours: minutes)
Declination: -05: 27 (degrees: minutes)
Distance: Approximately 1,344 light years
The Orion Nebula is a vast star-forming region located in the “sword”
branching off of the famous Orion’s Belt. Also known as Messier 42, this
diffuse nebula is bright enough to see with the unaided eye — although it will
only appear as a slightly foggy star. However, with your telescope, you can
see many of the beautiful details, such as the billowing clouds of gas and
dust where new stars are being born.
Image credit: NASA, ESA, M. Robberto (Space Telescope Science
Institute/ESA) and the Hubble Space Telescope Orion Treasury Project Team
Image credit: NASA/JPL- Caltech/UCLA
Pleiades Star Cluster(M45):
Right ascension: 03: 47.0 (hours: minutes)
Declination: +24: 07 (degrees: minutes)
Distance: Approximately 444 light years
The Pleiades Star Cluster is a group of brilliant blue stars located in the
Taurus Constellation. Also known as Messier 45 or “Seven Sisters”, this open
star cluster consists of more than 1,000 confirmed stars, although an average
of only six are visible to the unaided eye. With your telescope, you can
quickly reveal some of the more elusive members of this legendary and
beautiful cluster.
Image credit: NASA/JPL- Caltech
Andromeda Galaxy(M31):
Right ascension: 00: 42.7 (hours: minutes)
Declination: +41: 16 (degrees: minutes)
Distance: Approximately 2.54 million light years
The Andromeda Galaxy is the closest major galaxy to our own Milky Way. Also
known as Messier 31, this famous spiral galaxy is part of the Local Group of
galaxies. Although it is technically bright enough to see with the unaided eye
under a very dark sky, your telescope may show its bright center, hints of its
spiral structure and its much smaller companion galaxies known as M32 and
M110.
Dumbbell Nebula(M27)
Right ascension: 19:59.6 (hours: minutes)
Declination: +22:43 (degrees: minutes)
Distance: Approximately 1,360 light years
The Dumbbell Nebula was the first planetary nebula ever discovered. It is one
of the most popular sights in the Vulpecula constellation. Easy to find with
binoculars and amazing in a telescope, the shape of this bright, double-lobed
nebula has been compared to a dumbbell, an hourglass or an apple core. As an
added bonus, the white dwarf that lies at the heart of the Dumbbell Nebula is
larger than any other star of its kind.
Image credit: NASA/JPL-Caltech /Harvard-Smithsonian CfA
Note: Images are for illustration purposes only. Quality of your image may very depending upon atmospheric conditions and location.
Types Of Telescopes:
Reflector
A reflector telescope uses mirrors to gather and focus light. Light enters the
telescope through its open front end and travels to the concave primary mirror
at the back. From there the light is reflected back up the tube to a flat
secondary mirror, which sits at a 45° angle in relation to the eyepiece. Light
bounces off of this secondary mirror and out through the eyepiece. A reflector
telescope is designed for astronomical use. Terrestrial objects may appear
inverted, sideways or at an angle depending on how your tube is oriented due
to optical design. This rotation is perfectly normal on all Newtonian
reflectors and will not affect astronomical viewing.
Refractor:
A refracting telescope uses a collection of lenses to gather and focus light.
A refractor’s views will be upside down if a diagonal is not in use. A
standard diagonal will generate a “right side up” image, however, it will
rotate the image on the vertical axis (mirror image). To get the “right side
up” image without the rotation, you will need to use a special diagonal with
an erect image prism. Catadioptric:
A catadioptric telescope uses a combination of mirrors and lenses to gather
and focus light. Popular catadioptric designs include the Maksutov-Cassegrain
and Schmidt-Cassegrain.
Telescope Terms to Know:
Aperture:
This figure, which is usually expressed in millimeters, is the diameter of a
telescope’s light-gathering surface (objective lens in a refractor or primary
mirror in a reflector). Aperture is the key factor in determining the
brightness and sharpness of the image.
Objective Lens:
The objective lens is the main light-gathering component of a refractor
telescope. It is actually composed of several lens elements.
Diagonal:
This accessory houses a mirror that deflects the ray of light 90 degrees. With
a horizontal telescope tube, this device deflects the light upwards so that
you can comfortably observe by looking downwards into the eyepiece. The image
in a standard diagonal mirror appears upright, but rotated around its vertical
axis (mirror image). To get an image without this rotation, you will need to
use a special diagonal with an erect image prism.
Eyepiece:
An eyepiece is an optical accessory comprised of several lens elements. It
determines the magnification of a particular observing setup.
Primary Mirror:
The primary mirror is the principle light-gathering surface of a reflector
telescope.
Secondary Mirror:
A secondary mirror is a small mirror that sits at a 45° angle in relation to
the primary mirror of a reflecting telescope. Light from the primary mirror is
reflected back up the tube to the secondary mirror. The light is directed from
this mirror up into the eyepiece.
Magnification:
The magnification corresponds to the difference between observation with the
naked eye and observation through a magnifying device like a telescope. If a
telescope configuration has a magnification of 30x, then an object viewed
through the telescope will appear 30 times larger than it would with the naked
eye. To calculate the magnification of your telescope setup, divide the focal
length of the telescope tube by the focal length of the eyepiece. For example,
a 20mm eyepiece in a telescope with a 1000mm focal length will result in 50x
power, which will make the object appear 50 times larger. If you change the
eyepiece, the power goes up or down accordingly. Focal ratio
The focal ratio of a telescope is determined by dividing the telescope’s focal
length by its aperture (usually expressed in millimeters). It plays a key role
in determining a telescope’s field of view and significantly impacts imaging
time in astrophotography. For example, a telescope with a focal length of
1000mm and a 100mm clear aperture has a focal ratio of f/10. Focal length
(Telescope):
The focal length is the distance in millimeters between the objective lens or
primary mirror and the point at which entering light rays converge — otherwise
known as the focal point. The focal lengths of the telescope tube and the
eyepiece are used to determine magnification.
Focal length (Eyepiece):
The focal length is the distance in millimeters between the center of the
first lens element in an eyepiece and the focal point. The focal lengths of
the telescope tube and the eyepiece are used to determine magnification. Short
eyepiece focal lengths produce higher magnifications than long eyepiece focal
lengths.
Exit Pupil
The exit pupil is the diameter of the beam of light coming out of the
eyepiece. To calculate exit pupil, divide the focal length of your eyepiece by
your telescope’s focal ratio. For example, if you use a 20mm eyepiece with an
f/5 telescope, the exit pupil would be 4mm.
Eye Relief
Eye relief is all about a comfortable viewing experience because it is the
distance at which you need to position your eye from the eyepiece’s outermost
surface to enjoy the full field of view. This characteristic is of special
concern to observers who wear glasses to correct an astigmatism, because a
long enough eye relief is necessary to allow room for glasses. Huygenian Eyepieces:
A Huygenian eyepiece uses two plano-convex lenses separated by an air gap.
They have a fairly narrow apparent field of view.
Kellner Eyepieces:
A Kellner eyepiece uses three lens elements – two of which are paired together
in an achromatic doublet design to minimize chromatic aberrations. They
typically produce an apparent field of view around 45°.
Plössl Eyepieces:
A Plossl eyepiece uses two doublets (a pairing of lens) for a total of four
lens elements. This eyepiece design delivers sharp views and an apparent field
of view of approximately 50°, which works well for both planetary and deep sky
viewing.
Barlow Lens:
A Barlow lens effectively increases the focal length of a telescope. It is
inserted between the eyepiece and the focuser/diagonal (depending on the
optical setup) and multiplies the magnification power of the eyepiece. For
example, a 2x Barlow will double the magnification of a particular eyepiece.
©2022 Explore Scientific, LLC.
1010 S 48th Street, Springdale, AR 72762
explorescientificusa.com |
866.252.3811
All rights reserved. Made in China.
CONTENTS AND COLORS MAY VARY.
CONFORMS TO THE SAFETY REQUIREMENTS OF ASTM F963.
V042022
Customer Service: Call
1-866-252-3811
References
- Keep Exploring with Explore Scientific Telescopes, Microscopes, & STEM
- Documents — Explore Scientific
- P65Warnings.ca.gov
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>