EXPLORE SCIENTIFIC WSH4103 Smart Weather Station 4 Day Forecast With Air Quality Index Instruction Manual

June 5, 2024
EXPLORE SCIENTIFIC

EXPLORE logo
SCIENTIFIC WSH4103 Smart Weather Station 4-Day Forecast With Air Quality Index
Instruction Manual

SMART WEATHER STATION 4-DAY FORECAST WITH AIR QUALITY INDEX
Art.No.: WSH4103

EXPLORE SCIENTIFIC WSH4103 Smart Weather Station 4 Day Forecast With Air
Quality Index

ABOUT THIS INSTRUCTION MANUAL

These operating instructions are to be considered a component of the device.
Please read the safety instructions and the operating instructions carefully before use.
Keep these instructions for renewed use at a later date.
When the device is sold or given to someone else, the instruction manual must be provided to the new owner/ user of the product. The device is intended only for indoor use.

**** GENERAL WARNINGS

  • Risk of electric shock — This device contains electronic components. Only use the device as described in the manual; otherwise, you run the risk of an electric shock.
  • Choking hazard — Children should only use the device under adult supervision. Keep packaging material, like plastic bags and rubber bands, out of the reach of children, as these materials pose a choking hazard.
  • Risk of chemical burn — Keep batteries out of the reach of children! Make sure you insert the batteries correctly. Leaking battery acid can lead to chemical burns. Avoid contact of battery acid on skin, eyes, and mucous membranes. In the event of contact, rinse the affected region immediately with plenty of water and seek medical attention.
  • Risk of fire/explosion — Do not expose the device to high temperatures. Use only the recommended batteries. Do not short-circuit the device or batteries, or throw them into a fire. Excessive heat or improper handling could trigger a short circuit, a fire, or an explosion.
  • Do not disassemble the device. In the event of a defect, please contact your dealer. The dealer will contact the Service Centre and can send the device in to be repaired, if necessary.
  • Use only the recommended batteries. Always replace weak or empty batteries with a new, complete set of batteries at full capacity. Do not use batteries from different brands or with different capacities. The batteries should be removed from the unit if it has not been used for a long time.

SCOPE OF DELIVERY

Weather station, Operating instructions, 5V adapter, 2x AA batteries.

BEFORE YOU BEGIN

  • We recommend using alkaline batteries. If temperatures regularly fall below 0°C (32°F), we recommend using lithium batteries.
  • Avoid using rechargeable batteries. (Rechargeable batteries cannot maintain correct power requirements.)
  • Insert batteries before first use, matching the polarity in the battery compartment. Connect the AC/DC adapter with the Weather station. 2x AA Batteries are required for the Weather station for retaining the time.

PRODUCT OVERVIEW

EXPLORE SCIENTIFIC WSH4103 Smart Weather Station 4 Day Forecast With Air
Quality Index - fig

  1. Press [ TIME ] to view time, press and hold to enter time and date setting.
  2. Press [ AL SET ] to display the alarm. Press and hold to enter alarm setting.
  3. Press [ AL ON/OFF ] to turn on/off alarm time.
  4. In setting mode, press [ + ] to increase one unit, press and hold to increase rapidly.
  5. In setting mode, press [ – ] to decrease one unit, press and hold to decrease rapidly.
  6. Press [ LIGHT/SNOOZE ] to activate the backlight for 10 seconds or to activate the snooze function to delay the alarm by 5 minutes.
  7. Press and hold [ SET ] to reconfigure the network.
  8. Press [ SYN ] to resynchronize the time and 4-day weather. Press and hold to stop reconfiguring the network during network configuration.
  9. Press [ 12/24H ] to switch between the 12-hour and 24-hour time format.
  10. Wall mount
  11. Battery compartment
  12.  Table stand
  13. DC Jack (5V/1A)

EXPLORE SCIENTIFIC WSH4103 Smart Weather Station 4 Day Forecast With Air
Quality Index - fig 1

BUTTON
MODE| TIME| AL SET| AL ON/OFF| +| –| SET| LIGHT/SNOOZE| SYN
---|---|---|---|---|---|---|---|---
Standard
mode| PRESS| Time
display| | Turn Alarm
on/off| | | | 1. Turn on
backlight for 10
seconds
2. SNOOZE 5
minutes when
alarm is ringing| Resynchronize
time and 4-day
weather
| | |
HOLD| Enter into
time
setting| Enter into
alarm
setting| Enter into
alarm setting| | | Reconfigure
the network| | Stop reconfiguring
the network
during network
configuration
| |
Setting
mode| PRESS| Confirm
setting| | | Increase| Decrease| | Turn on backlight
for 10 seconds|
| | |
HOLD| | | | Quick
Increase| Quick
Decrease| | |
| | | | |

LCD DISPLAY

EXPLORE SCIENTIFIC WSH4103 Smart Weather Station 4 Day Forecast With Air
Quality Index - fig 2

  1. Weather of TODAY
  2. Indoor Temperature & humidity
  3. Time, date, week and alarm
  4. Indoor comfort indication
  5. Barometer and barometric trend
  6. Network connection status
  7. Temperature range and humidity of TODAY
  8. Weather forecast and Temperature range of DAY 2-DAY4
  9. AQI (Air Quality Index) value and indication
    [ ] Low battery indicator
    [ ] Ice alert indicator
    [ ] Alarm

GETTING STARTED

INSERT BATTERIES AND PLUG IN THE ADAPTER
1. Remove the battery door from the back.
2. Insert 2x AA (LR06)/1.5V batteries. Please ensure the polarities (+/-) of the batteries match upon installation.
3. Reattach the battery door.
4. Plug in the power adapter for a stronger and more stable Wi-Fi connection.
NOTE:
– Replace batteries when [  ] displays, or when the display is dim.
– The batteries provide power to the console for retaining the clock time.
SMART LIFE APP
ACCOUNT REGISTRATION
The console works with SmartLife APP for both Android and iOS smart phone.

  1. Scan the QR code to go to the Smart Life download pageEXPLORE SCIENTIFIC WSH4103 Smart Weather Station 4 Day Forecast With Air Quality Index - qr codehttps://smartapp.tuya.com/smartlife
    Smart Life for Andriod / iOS

  2. Download Smart Life from Google Play or Apple App store.

  3. Install the Smart Life App.

  4. Follow the instruction to create your own account using your phone number or email address.

  5. Once the account registration is completed, the Home Screen will be shown.

NOTE:
– No registration code is needed if you use an email address to register the account.
– The APP may be subject to change without notice.
CONNECT WEATHER STATION TO WIFI NETWORK
1. When the console is powered up for the first time, the console will automatically enter and stay at setting mode. You may also set the network manually.
SET THE NETWORK MANUALLY
Press and hold the [ SET ] key for 6 seconds to enter setting mode manually. [ ] blinks. [ ] stops blinking upon a successful network configuration.
2. Open Smart Life App and follow the in-app instructions to connect the weather station to your Wi-Fi network.
Step 1. Enable location. Turn on Bluetooth. Make sure the Wi-Fi network is stable.
Step 2. Make sure the device, your smartphone, and your Wi-Fi router are not placed far away from each other.

Step 3. You will be prompted to the “Devices to be added” page. Tap “Add”.| Step 4. Tap “+”.
---|---
EXPLORE SCIENTIFIC WSH4103 Smart Weather Station 4 Day Forecast With Air
Quality Index - Device
Step 5. Make sure you selected a 2.4G Wi-Fi network of your place. Enter your password then tap the “Next”. NOTE: This weather station is not compatible with 5G network.| Step 6. The APP starts connecting the device. It takes several minutes to connect the device. When finished, tap “Done”.| Step 7.Once it has finished connecting the
device, the check mark will be shown. You can customize its name by taping the pen icon . Tap “Done” to go to the weather information page.
---|---|---
EXPLORE SCIENTIFIC WSH4103 Smart Weather Station 4 Day Forecast With Air
Quality Index - Device 1

Step 8. Tap “<” to return to home screen. The device is located under “All Devices”. EXPLORE SCIENTIFIC WSH4103 Smart Weather Station 4 Day Forecast
With Air Quality Index - Device 2

SMART LIFE APP

INTERFACE OVERVIEW

EXPLORE SCIENTIFIC WSH4103 Smart Weather Station 4 Day Forecast With Air
Quality Index - Device 3

  1. Weather, temperature, humidity, AQI of TODAY at your location
  2. Weather and temperature forecast for DAY 2, 3 and 4
  3. Back to home page
  4. Advanced features and firmware updates

SET THE CLOCK MANUALLY
This console is designed to obtain the time by synchronizing with your local time from the APP. It will synchronize the time and weather information everyday. If you want to use it offline, you can set the time and date manually.

  1. Press and hold the [ TIME ] button to enter into the time and date setting.

  2. The setting parameter will flash.

  3. Press the [ + ] button once, and the figure will increase by 1 unit. Press and hold the [ + ] button, the figures will increase rapidly.

  4. Press the [ – ] button once, and the figure will decrease by 1 unit. Press and hold the [ – ] button, the figures will decrease rapidly.

  5. Press the [ TIME ] button to confirm the setting and enter to next parameter.

  6. Sequence of setting:
    12/24h format Hour Minute Year Date format (D M / M D) Month Day Language Pressure unit Temperature unit (°C/°F) Exit

  7. If there is no action in 20 seconds, the setting will be saved and you will exit the setting mode.

ALARM

SETTING/ADJUSTING ALARM TIME

  1. Press [ AL SET ] to display alarm time. Press and hold [ AL SET ] to enter alarm setting mode.
  2.  The setting parameter will flash.
  3. Press [ + ] or [ – ] button to set the desired data.
  4. Press the [ AL SET ] button to confirm the setting and exit.
  5. The alarm will sound when the alarm setting is finished and turned on.

TURN ON/OFF THE ALARM
Press the [ AL ON/OFF ] button to turn on/off the alarm.

OPERATION

  1. At the set alarm time, the alarm signal rings.
  2. During the alarm, press the [ LIGHT/SNOOZE ] button to delay the alarm by 5 minutes.
  3. If you do not press any button to stop the alarm, it will automatically turn off after 2 minutes.
  4. To stop the alarm, press any other button, except for [ LIGHT/SNOOZE ].
  5. The alarm will start again at the next alarm time unless you switch off the alarm function by pressing the [ AL ON/OFF ] button until the alarm is set to off.

WEATHER FORECAST
This device displays the weather forecast information of the next 3 days. EXPLORE SCIENTIFIC WSH4103 Smart Weather Station 4 Day Forecast With Air
Quality Index - fig 3

AQI (AIR QUALITY INDEX)
The Air Quality Index is a scale used to rate the quality of the air. In the United States, the Air Quality Index is defined by the EPA. The scale runs from 0-500 and has six different levels.

EXPLORE SCIENTIFIC WSH4103 Smart Weather Station 4 Day Forecast With Air
Quality Index - fig 4

NOTE:
– The rating takes five different pollutants into consideration: ground-level ozone, particle pollution, carbon monoxide, sulfur dioxide, and nitrogen dioxide. The goal is to give you a simple metric for understanding the air quality at any given time.
– Other countries, such as the United Kingdom, Germany, and India, use their own Air Quality Index methodology, but the concept is the same.
INDOOR COMFORT INDICATION
The comfort indication is a pictorial indication based on indoor air temperature and humidity in an attempt to determine comfort level.

SYMBOL DESCRIPTION
Too dry
Comfortable
Too wet

NOTE: Comfort indication can vary under the same temperature, depending on the humidity.
BAROMETER
The trend of the air pressure within the last 12 hours is displayed in the form of a bar diagram. The scale goes from 1 (1 hour ago) to 12 (12 hours ago).

To change the unit of pressure between mmHg/inHg/ hPa, press and hold [ TIME ], then press [ TIME ] several times to enter the pressure unit setting.

LANGUAGE

1. Press and hold the [ TIME ] button to enter the time setting, press [ TIME ] several times to enter the language setting.
2. Sequence of setting weekday language:
German (GE)  English (EN) Italian (IT) French (FR) Netherlands (NE) Spain (ES) Danish (DA)

| German| English| Italian| French| Netherlands| Spanish| Danish
---|---|---|---|---|---|---|---
Symbol| GE| EN| IT| FR| NE| ES| DA
Monday| MO| MO| LU| LU| MA| LU| MA
Tuesday| DI| TU| MA| MA| DI| MA| TI
Wednesday| MI| WE| ME| ME| WO| MI| ON
Thursday| DO| TH| GI| JE| DO| JU| TO
Friday| FR| FR| VE| VE| VR| VI| FR
Saturday| SA| SA| SA| SA| ZA| SA| LO
Sunday| SO| SU| DO| DI| ZO| DO| SO

TEMPERATURE AND HUMIDITY

The indoor temperature and humidity are always displayed in the top right corner of the screen. NOTE: When the temperature is lower than -10 °C (14.0 °F), the screen displays LL.L. When the temperature is higher than 50 °C (122.0 °F), the screen displays HH.H.
ICE ALERT
If the temperature falls between -2°C to 3°C (28°F
to 37°F), the ice alert indicator [ ] will display will disappear once the temperature is out of
this range.
BACKLIGHT
Press [ LIGHT/SNOOZE ] to activate the backlight for10 seconds.

SPECIFICATIONS

MAIN UNIT:
Dimensions
185 x 25 x 120 mm (L x W x H)
Weight
280 g (Exclude batteries)
Power:
2x AA (LR06) 1.5V batteries 5V/1A Adapter
TEMPERATURE:
Temperature display range:

-10°C to +50°C (14°F to 122°F)
HUMIDITY:
Humidity display range: 20% – 95% RH

EC DECLARATION OF CONFORMITY

Hereby, Guangzhou Bresser Optical Instruments Co., Ltd declares that the WSH4103 product complies with directive 2014/53/EU.
The full text of the Declaration of Conformity is available at the following web address: https://www.explorescientific.it/certificati- diconformita/WSH4103.pdf
RCM DECLARATION OF CONFORMITY
**** The adapter complies with electrical safety and radio spectrum regulatory requirements for products supplied to the Australia or New Zealand market.

FCC DECLARATION OF CONFORMITY

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20cm between the radiator & your body.
Suppliers Name : Guangzhou Bresser Optical  Instrument Co., Ltd.
Suppliers Address : Kangda Rd. 12, Yunpu Ind. Area, Huangpu, Guangzhou, PRC
Suppliers phone number : 866.252.3811
NOTES ON CLEANING

  • Remove the batteries before cleaning.
  • Only use a dry cloth to clean the exterior of the device. To avoid damaging the electronics, do not use any cleaning fluid.
  • Protect the device from dust and moisture.

DISPOSAL
Dispose of the packaging materials properly, according to their types, such as paper or cardboard. Contact your local waste disposal service or environmental authority for information on the proper disposal.
Do not dispose of electronic devices in the household garbage!
As per the Directive 2002/96/EC of the European Parliament on waste electrical and electronic equipment and its adaptation into German law, used electronic devices must be collected separately and recycled in an environmentally friendly manner.|
In accordance with the regulations concerning batteries and rechargeable batteries, disposing of them in normal household waste is explicitly forbidden. Please make sure to dispose of your used batteries as required by law — at a local collection point or in the retail market. The disposal of domestic waste violates the Battery Directive. Batteries that contain toxins are marked with a sign and a chemical symbol.

  1. battery contains cadmium
  2. battery contains mercury
  3. battery contains lead

WARRANTY & SERVICE

– EU –
The product will be free from defects in materials and workmanship for a period of 24 months starting from the date indicated in the purchase document.
The warranty terms and conditions can be consulted on the following website:
https://www.explorescientific.it/warranty
– US –
Manual download: www.explorescientific.com/weather- clock manuals
Service and Warranty: www.explorescientific.com/warranty

MANUAL DOWNLOAD/DOWNLOAD
– EU Version – https://bit.ly/ES_WSH4103_2022IM
– US Version – https://www.explorescientific.com/weather-clock- manuals
Explore Scientific, LLC
1010 S. 48th Street, Springdale, AR 72762 www.explorescientificusa.com
Errors and technical changes reserved.
ManualWSH4103EUAUSUS2022062001

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

EXPLORE SCIENTIFIC User Manuals

Related Manuals