EXPLORE SCIENTIFIC WSH4003 Weather Station with Multiple Sensors Instruction Manual

EXPLORE SCIENTIFIC WSH4003 Weather Station with Multiple Sensors

Instruction Manual

EXPL@RE® SCIENTIFIC

WEATHER STATION WITH MULTIPLE SENSORS STAZIONE METEO CON SENSORI MULTIPLI WETTERSTATION MIT MEHREREN SENSOREN STATION MÉTÉO AVEC CAPTEURS MULTIPLES ESTACIÓN METEOROLÓGICA CON VARIOS SENSORES WEERSTATION MET MEERDERE SENSOREN

Art.No.: WSH4003

ABOUT THIS INSTRUCTION MANUAL

These operating instructions are to be considered a component of the device. Please read the safety instructions and the operating instructions carefully before use.
Keep these instructions for renewed use at a later date. When the device is sold or given to someone else, the instruction manual must be provided to the new owner/user of the product. The device is intended only for indoor use.

GENERAL WARNINGS

• Risk of electric shock — This device contains electronic components. Only use the device as described in the manual; otherwise, you run the risk of an electric shock.
• Choking hazard — Children should only use the device under adult supervision. Keep packaging material, like plastic bags and rubber bands, out of the reach of children, as these materials pose a choking hazard.
• Risk of chemical burn — Keep batteries out of the reach of children! Make sure you insert the batteries correctly. Leaking battery acid can lead to chemical burns. Avoid contact of battery acid with skin, eyes and mucous membranes. In the event of contact, rinse the affected region immediately with a plenty of water and seek medical attention.

Risk of fire/explosion

Do not expose the device to high temperatures. Use only the recommended batteries. Do not short-circuit trigger a short-circuit, a fire, or an explosion.

• Do not disassemble the device. In the event of adefect, please contact your dealer. The dealer will contact the Service Centre and can send the de vice in to be repaired, if necessary.
• Use only the recommended batteries. Always replace weak or empty batteries with a new, complete set of batteries at full capacity. Do not usebatteries from different brands or with differentcapacities. The batteries should be removed from the unit if it has not been used for a long time.

SCOPE OF DELIVERY

Weather station, 3x Outdoor sensor (ST1004H), Operating instructions, 9x AAA batteries

BEFORE YOU BEGIN

• We recommend using alkaline batteries. If temperatures regularly fall below 0°C (32°F), we recommend using lithium batteries.
• Avoid using rechargeable batteries. (Rechargeablebatteries cannot maintain correct power requirements.)
• Insert batteries before first use, matching the polarity in the battery compartment. 3x AAA Batteries are required for the Weather station and 2x AAA Batteries are required for each Outdoor sensor.

PRODUCT OVERVIEW

1. P ress [ SNZ / LIGHT ] to activate the backlight or to activate the snooze function to delay the alarm for 5 minutes.

2. While in normal display mode, press [ UP ] to check max. and min. temperature. While displaying max. and min. data, press and hold [ UP ] to clear all memory and return to normal display mode. While in setting mode, press [ UP ] to increase one unit, press and hold to increase rapidly.

3. While in normal display mode, press [ DOWN ] to select °C or °F. Press and hold [ DOWN ] to initiate or exit RCC receiving. While in setting mode, press [ DOWN ] to decrease one unit, press and hold to decrease rapidly.

4. Press [ CH ] to toggle between outdoor sensor channel 1-3. Press and hold to clear present channel.

5. Press [ MODE ] to enter time setting mode.

6. Press [ ALARM ] once to check alarm time. Press [ ALARM ] once more to turn on/off the alarm. Press and hold [ ALARM ] to enter alarm setting mode.

7. Wall Mount.

8. Battery compartment.

9. Table stand.

OUTDOOR SENSOR

1. Battery compartment door.
   

2. Battery compartment.

3. RESET button (reset all settings).

4. Channel switch.

5. Data transmission light

BUTTON

MODE

|

SNZ/LIGHT

|

ALARM

|

CH

|

DOWN

|

UP

|

MODE

---|---|---|---|---|---|---

Standard mode

|

PRESS

|

Turn on backlight

SNOOZE

when alarm is ringing

|

Check alarm time Turn Alarm on/off

|

Toggle between outdoor sensor channel 1-3

|

Select

。C or 。F

|

Check max. and min. temperature.

Clear all memory when display

max. and min. data.

|

Enter into time setting

HOLD

|

Set

the snooze time

|

Enter into alarm setting

|

Clear present channel

| Initiate or exit RCC

receiving

|

|

Time setting mode

|

PRESS

|

| | |

Decrease

|

Increase

| Confirm setting

HOLD

|

|

|

|

Quick Decrease

|

Quick Increase

|

Alarm setting mode

|

PRESS

|

|

|

|

Decrease

|

Increase

| Confirm setting

HOLD

|

|

|

|

Quick Decrease

|

Quick Increase

|

LCD DISPLAY

1. Time/Alarm display
2. Calendar
3. Indoor Temperature and Humidity display
4. Outdoor Temperature and Humidity display

GETTING STARTED INSERT BATTERIES

1. Remove the battery door from the back.
2. Insert 3x AAA (LR03)/1.5V batteries. Please ensure the polarities (+/-) of the batteries match upon installation.
3. Reattach the battery door.
   NOTE: Replace batteries when [ ] when the display is dim.

OUTDOOR SENSOR

The main unit can receive data from up to 3 outdoor sensors. 3 sensor are included with delivery.

1. Remove the battery door from the back.
2. .Select a channel.
3. Insert 2x AAA (LR03)/1.5V batteries. Please ensure the polarities (+/-) of the batteries match upon installation.
4. Reattach the battery door.
5. Place the sensor within 30 m (98 ft) of the main unit using the table stand or wall mount.

TO SEARCH FOR A SENSOR:

The main unit will automatically search for a new sensor after the batteries are installed. To manually initiate an outdoor sensor search, press and hold [ CH ].
NOTE: The transmission range may vary depending on many factors. You may need to experiment with various locations to get the best results.

CLOCK CLOCK RECEPTION

1. When you insert or replace the batteries, RCC reception is initiated. To manually start RCC reception, press and hold the [ DOWN ] button.
2. After the RCC receives the signal, if you change the relevant display settings (such as year, month, day, hour, minute, etc.), the RCC symbol [ ] will automatically disappear.
3. If the RCC receiving process is successful, a completed RCC symbol [ ] will be shown in the display and the date and time will be set automatically. If it fails, press and hold the [ DOWN ] button to re-initiate RCC receiving.
4. RCC receiving will automatically start from 1:00 – 5:00 every night. Auto receiving function will cease if it is successful. If it does not receive the RCC signal, it will receive in next day.
5. If the device is still not receiving the signal, please proceed to set the time manually.

SET THE CLOCK MANUALLY

1. Press and hold [ MODE ] button to enter into time and date setting.

2. The setting parameter will flash.

3. Press [ UP ] button once, the figure will increase 1 unit. Press and hold the [ UP ] button, the figures will increase rapidly.

4. Press [ DOWN ] button once, the figure will decrease 1 unit. Press and hold the [ DOWN ] button, the figures will decrease rapidly.

5. Press [ MODE ] button to confirm setting and enter to next parameter.

6.  Sequence of setting: 12/24HR Time Zone Hour Minute Year Month Day Week language Exit
   NOTE: Week language setting order: EN GE FR IT DU SP DA

7. If there is no action in 20 seconds or if you press [ MODE ] button, the setting will be saved and you will exit the setting mode.

°C/°F SETTING

Press [ DOWN ] button to switch Celsius (°C) / Fahrenheit (°F).

ALARM

SETTING/ADJUSTING ALARM TIME

1. Press [ ALARM ] to display the alarm time.
2. Press and hold [ ALARM ] button to enter alarm setting mode.
3. The setting parameter will flash.
4. Press [ UP ] or [ DOWN ] button to set the desired data.
5. Sequence of setting: Hour Minute Exit
6. Press [ ALARM ] button to confirm setting and exit.
7. Alarm will sound when alarm setting is finished and turned on.

TURN ON/OFF ALARM

Press [ ALARM ] to display the alarm time. Press the [ ALARM ] button once more to turn on/off the alarm.

SNOOZE FUNCTION

1. At the set time, alarm signal rings.
2.  During the alarm, press the [ SNZ / LIGHT ] button to delay the alarm by 5 minutes.
3. To stop the alarm, press any other button, except for [ SNZ / LIGHT ] button.
4. The alarm will start again at the next alarm time, unless you turn off the alarm function by pressing the [ ALARM ] button to display the alarm time first, then press the [ ALARM ] button once more until the alarm is set to off

TEMPERATURE AND HUMIDITY

The indoor temperature is always displayed in the centre of the screen. To receive outdoor temperature you can connect up to 3 outdoor sensors to the main unit.
Press the [ CH ] button to toggle between Channel 1-3.

MANUAL MEASUREMENT DISPLAY

1. Press [ UP ] button to display the max. and min. temperature.
2. Display order: Current values > MAX (highest values) > MIN (lowest values)
3. When displaying highest or lowest values, press and hold [ UP ] button to delete all saved values.

BACKLIGHT

Press [ SNZ / LIGHT ] to activate backlight.

SPECIFICATIONS

MAIN UNIT:

Dimensions

141 x 21 x 124 mm (L x W x H)

Weight

220 g (Exclude batteries)

Power:

3x AAA (LR03) 1.5V batteries

TEMPERATURE:

Indoor temperature display range:

0°C to +50°C (32°F to 122°F)

Outdoor temperature display range:

-40°C to +70°C (-40°F to 158°F)

HUMIDITY:

Indoor/outdoor humidity range:

20% – 99% R

OUTDOOR SENSOR:

Dimensions:

50 x 25 x 95 mm (L x W x H)

Weight:

45 g (Exclude batteries)

Transmission range:

30 m (98 ft)

Temperature range:

-40°C to +70°C (-40°F to 158°F)

Humidity range:

20% – 95% RH

Signal frequency:

433 MHz

Maximum transmission power:

under 10mW

Power:

2x AAA (LR03) 1.5V batteries

NOTES ON CLEANING

• Remove the batteries before cleaning.
• Only use a dry cloth to clean the exterior of the device. To avoid damaging the electronics, do not use any cleaning fluid.
• Protect the device from dust and moisture.

DISPOSAL

Dispose of the packaging materials properly, according to their type, such as paper or card board. Contact your local waste-disposal service or environmental authority for information on the proper disposal.

Do not dispose of electronic devices in the household garbage!
As per the Directive 2002/96/EC of the European Parliament on waste electrical and electronic equipment and its adaptation into German law, used electronic devices must be collected separately andrecycled in an
environmentally friendly manner.

In accordance with the regulations concern ing batteries and rechargeable batteries, disposing of them in the normal household waste is explicitly forbidden. Please make sure to dispose of your used batteries as required by law — at a local collection point or in the retail market.
Disposal in domestic waste violates the Battery
Directive. Batteries that contain toxins are marked with a sign and a chemical symbol.

1. battery contains cadmium
2. battery contains mercury
3. battery contains lead

WARRANTY & SERVICE

The regular guarantee period is 5 years and
begins on the day of purchase. You can consult the full guarantee terms as well as information on extending the guarantee period and details of our services at www.bresser.de/warranty_terms.
Would you like detailed instructions for this product in a particular language? Then visit our website via the link below (QR code) for available versions.
Alternatively you can also send an email to manuals@bresser.de or leave a message on
+49 (0) 28 72 – 80 74-220. Please always state your name, precise address, a valid phone number and email address, as well as the article number and name.
Number charged at local rates in Germany (the amount you will be charged per phone call will depend on the tariff of your phone provider); calls from abroad will involve higher costs

MANUAL DOWNLOAD:
www.bresser.de/download/WSH4003

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>