EXPLORE SCIENTIFIC RDC1005 Radio-Controlled Alarm Clock Instruction Manual

: June 6, 2024
: EXPLORE SCIENTIFIC

EXPLORE SCIENTIFIC RDC1005 Radio-Controlled Alarm Clock Instruction Manual

ABOUT THIS INSTRUCTION MANUAL
These operating instructions are to be considered a component of the device. Please read the safety instructions and the operating instructions carefully before use. Keep these instructions for renewed use at a later date. When the device is sold or given to someone else, the instruction manual must be provided to the new owner/user of the product. The device is intended only for indoor use.

GENERAL WARNINGS

Risk of electric shock — This device contains electronic components that operate via a power source (batteries). Children should only use the device under adult supervision. Only use the device as described in the manual; otherwise, you run the risk of an electric shock.
Choking hazard — Children should only use the device under adult supervision. Keep packaging material, like plastic bags and rubber bands, out of the reach of children, as these materials pose a choking hazard.
Risk of chemical burn — Keep batteries out of the reach of children! Make sure you insert the batteries correctly. Leaking battery acid can lead to chemical burns. Avoid contact of battery acid with skin, eyes and mucous membranes. In the event of contact, rinse the affected region immediately with a plenty of water and seek medical attention.
Risk of fire/explosion — Do not expose the device to high temperatures. Use only the recommended batteries. Do not short-circuit the device or batteries, or throw them handling a new, complete set of batteries at full capacity.
Do not disassemble the device. In the event of a defect, please contact your dealer. The dealer will contact the Service Centre and can send the device in to be repaired, if necessary.
Use only the recommended batteries. Always replace weak or empty batteries with a new, complete set of batteries at full capacity. Do not use batteries from different brands or with different capacities. The batteries should be removed from the unit if it has not been used for a long time.

SCOPE OF DELIVERY

Alarm clock, Operating instructions, 2x AAA Batteries

BEFORE YOU BEGIN

We recommend using alkaline batteries. If temperatures regularly fall below 0°C (32°F), we recommend using lithium batteries.
Avoid using rechargeable batteries. (Rechargeable batteries cannot maintain correct power requirements.)
Insert batteries before first use, matching the polarity in the battery compartment. 2x AAA Batteries are required.

PRODUCT OVERVIEW

LCD DISPLAY

GETTING STARTED

INSERT BATTERIES

Remove the battery door from the back.
Insert 2x AAA (LR03)/1.5V batteries. Please ensure the polarities (+/-) of the batteries match upon installation.
Reattach the battery door.

NOTE: Replace batteries when [ ] displays or when the display is dim.

CLOCK

CLOCK RECEPTION

Replace batteries or press [ ] button will initiate RCC receiving.
RCC receiving can work in both date mode and alarm mode.
The receiving process duration is 7 minutes.
During receiving process, the RCC signal symbol [ ] flashes.
If the RCC receiving process is successful, a completed RCC symbol [ ] will be shown the display and the date and time will be set automatically. If it fails within 7 minutes, RCC setting will quit automatically. If that happens, press [ ] button to re-initiate NL RCC receiving.
RCC receiving will automatically start at 2:03, 3:03, 4:03, 5:03 every night. Auto receiving function will cease if it is successful.
To stop RCC reception, press the [ ] button.
If the device is still not receiving the signal, please proceed to set the time manually.

SET THE CLOCK MANUALLY

Press and hold [ ] button to enter time and date setting.

LANGUAGE

Sequence of setting weekday language: German (GER) English (ENG) French (FRE) Italian (ITA) Dutch (DUT).

TIME ZONE SETTING

°C/°F SETTING

ALARM

SETTING/ADJUSTING DUAL ALARM TIME

TURN ON/OFF ALARM

Press the [ ] button once to turn on/ off the alarm that is nearest in time. (1-5) or activated.
How activate alarm times individually:

OPERATION

SPECIFICATIONS

Dimensions (Main unit): 72 x 25 x 75 mm (L x W x H)
Weight (Main unit): 73g (Exclude batteries)
Temperature display range: -10°C to +50°C (14°F to 122°F)
Power: 2x AAA (LR03) 1.5V batteries

NOTE

When the temperature is lower than -10°(14°), the temperature displays LL.L. When the temperature is higher than 50°(122°), the temperature displays HH.H.
During alarm rings or RCC receiving process, temperature detection will be stopped.

NOTES ON CLEANING

Remove the batteries before cleaning.
Only use a dry cloth to clean the exterior of the device. To avoid damaging the electronics, do not use any cleaning fluid.
Protect the device from dust and moisture.

EC DECLARATION OF CONFORMITY

Hereby, Folux GmbH declares that the equipment type with part number RDC1005 is in compliance with Directive: 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.bresser.de/download/RDC1005/CE/RDC1005_CE.pdf

RCM DECLARATION OF CONFORMITY

The product complies with electrical safety, EMC and radio spectrum regulatory requirements for products supplied to the Australia or New Zealand market.

DISPOSAL

WARRANTY & SERVICE

The regular guarantee period is 5 years and begins on the day of purchase. You can consult the full guarantee terms as well as information on extending the guarantee period and details of our services at www.explorescientific.com/warranty.
Would you like detailed instructions for this product in a particular language? Then visit our website via the link below (QR code) for available versions.

https://explorescientific.com/pages/warranty-1

Errors and technical changes reserved

Folux GmbH
Gutenbergstr. 2 · DE-46414 Rhede · Germany
www.bresser.de · [email protected]

Explore Scientific, LLC
1010 S. 48th Street, Springdale, AR 72762
www.explorescientific.com