Hotspot Tech Hk Industrial HSV8112W 1080P HD Wireless WiFi Transmitter User Manual
- June 6, 2024
- Hotspot Tech Hk Industrial
Table of Contents
1080P HD Wireless WiFi Transmitter
User Manual
☑ HSV8112W
☑ HSV8113W
Product Introduction
HD extender transmits HD audio and video signal via wireless WIFI, and meanwhile supports IR remote control function. Featured by excellent image processing and transmission capability, this device makes it smoother and more stable to transmit signals, which is an economical and efficient HD signal transmission device.
Main Features
- HD signal wireless transmission;
- Under barrier-free environment without interference, HSV8112W: 150m; HSV8113: 200m;
- HSV8112W: One transmitter and one receiver;
- HSV8113W: One transmitter and four receivers; the distance will be shortened as the increase of receivers;
- Support to remotely control video sources;
- Built-in ESD electrostatic protection circuit to comprehensively protect the safety of system;
- Easy and convenient to install, plug, and use, and no settings required.
Installation Steps
- Connect to HD cables first, then connect the signal source to Sender (transmitting terminal) IN input; Connect the local display device to Sender (transmitting terminal) LOOPOUT output;
- Connect the extender’s Receiver (receiving terminal) to the remote display device (such as TV and splicing screen);
- IR Remote Control: Please align the IR end of the extender on the transmitting terminal with the IR receiving terminal of the signal source that requires to be controlled, and make them close to each other.
Connection Diagrams
4.1 HSV8112W: One transmitter and one receiver, wireless application
4.2 HSV8113W: One transmitter and multiple receivers, wireless application
4.3 Pairing Method
Pairing Method: Connect HD cable to TX input and RX output after 25s from the time of being electrified, wait for 10s after unplug, then make it be electrified.
Ports Descriptions
5.1 Transmitting Terminal Device
5.1.1 Front Panel
| Mark | Type | Instructions |
|---|---|---|
| DC 12V | Power port | 12V power input |
| POWER | Power indicator | Be always-on after being electrified |
| RESET | Reset key | Restore factory settings after long press for 5s, and |
require to pair again
IN| Input port| HD video signal input
LOOP OUT| Output port| HD video signal loop out
5.1.2 Rear Panel
| Mark | Type | Instructions |
|---|---|---|
| IR | Output port | Connect to IR transmitting terminal and make it close to |
signal source
5.2 Receiving Terminal Device
5.2.1 Front Panel
| Mark | Type | Instructions |
|---|---|---|
| DC 12V | Power port | 12V power input |
| POWER | Power indicator | Be always-on after being electrified |
| RESET | Reset key | Restore factory settings after long press for 5s, and |
require to pair again
OUT| Output port| HD video signal loop out
5.2.2 Rear Panel
| Mark | Type | Instructions |
|---|---|---|
| IR | Input port | Connect to IR receiving terminal and make it close to the |
remote control
Parameters
| Parameters | Instructions |
|---|---|
| Supported Protocol | HDMI 1.3; HDCP 1.3 |
| The Max. Supported Resolution Ratio | 1920X1080P@60Hz |
| Frequency Range of IR Remote Control | 20~60KHz |
| Wireless Standards | 802.11a/n |
| The Max. Wireless Transmission Distance | (Barrier-free) 8112W 150m; 8113W 200m |
| Working Temperature | -5℃ ~ +70℃ |
| Working Humidity | 5% ~ 90% |
| Wireless Transmission Frequency | 5GHz |
FAQ
Q: Why does the wireless icon on the top-right corner of the RX receiving
terminal be gray?
A: 1）Check whether the TX (the transmitting terminal) is connected to power
well and whether the indicator is on;
2） Check whether the transmitting distance is beyond the limit, or whether
there are too many barriers such as walls. Try to install in a place without
barriers and interference.
Q: Why does IR reverse control fail to work?
A: 1）Check whether IR terminals are properly connected, and separately install
them according to
2） Check whether the IR transmitting end on the transmitting terminal aligns
with the receiver of the signal source, see the diagram;
3） Check whether the IR frequency is within the scope of 20KHz~60KHz.
FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance 20cm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>