Frugal Hotspot 1562478 Sanctuary 10.8 cu ft Executive Safe Instruction Manual

Frugal Hotspot 1562478 Sanctuary 10.8 cu ft Executive Safe

DISCLAIMER – READ BEFORE SAFE SETUP

PLEASE READ THIS INFORMATION CAREFULLY BEFORE OPERATING YOUR SANCTUARY SAFE.

DO NOT LOCK THIS MANUAL OR THE BACKUP KEYS IN YOUR SAFE.

• Thank you for choosing a Sanctuary Safe to protect your valuables. We are committed to securing, organizing and protecting your firearms and most important documents and valuables.
• Your safe is built to last a lifetime. However, please understand that the locking mechanism has precision parts. If you experience ANY difficulty opening or closing your safe. DO NOT FORCE THE SAFE OPEN. Doing so may jam the components in the lock, which will require a safe technician to unlock your safe. This causes an inconvenience to you and may lead to a claim denial.
• If you experience problems or challenges with your safe, please contact us. Many issues can be quickly resolved without the product being returned.

Customer Service – (888} 792-4264 AVAILABLE M-F 9am – 5pm CT, English Speaking

SAFETY

• Safe bodies and doors are extremely heavy thus SA Consumer Products Requires a minimum of two people to insure stability of the safe during installation. Always ensure proper installation, as laid out in this manual, and do not open the door with the safe on an uneven or unstable floor. Ignoring this could result in serious injury or death.
• Keep a record of your security code in a secure place, away from children, and separate from your safe. You will need this information along with your proof of purchase to obtain technical assistance and replacement keys.

WEAPON STORAGE

• If you choose to utilize this safe to store a weapon always follow proper weapon and local laws when storing a weapon.
  SA Consumer Products strongly recommends that you do not store loaded guns.
  Always follow the firearm safety rules set out by the firearm’s manufacturer.
  A Sanctuary Safe or any other firearm storage device cannot take the place of other safety procedures including advising children of the dangers of firearms.
  SA Consumer Products and its distributors of the Sanctuary Safes do not recommend, suggest, advise, promote, or otherwise condone the ownership or use of firearms. We believe the decision to own or use a firearm is a serious decision that should only be made by an adult who has carefully considered the risks and benefits of such a decision.

REGISTRATION

Please ensure you register your safe by visiting our website. Locate the “contact” button on the top header on the home page. Select registration from the drop down menu.

www.saproducts.com

By registering your Sanctuary Safe we will be able to expedite and address any problems or challenges you may have which would otherwise require a notary letter and proof of payment.

REGISTRATION INFORMATION

The information you record onto this page will be required in the event youcannot access the contents of your Sanctuary Safe. Please fill out all the required information below and retain for your records and safe keeping.

PLEASE HAVE THIS INFORMATION READY PRIOR TO CALLING FOR TECHNICAL ASSISTANCE AT:

• PURCHASE DATE:
• PURCHASE PRICE (BEFORE TAX):
• MODEL NUMBER:
• SERIAL NUMBER:
• RETAILER PURCHASED AT:
• KEY NUMBER (IF APPLICABLE):

UNDERSTANDING YOUR SAFE

UNBOXING

WARNING: SAFES ARE HEAVY AND CAN BE UNSTABLE ON UNEVEN GROUND. PLEASE ENSURE EXTRA CAUTION WHEN DEALING WITH OR MOVING UNSECURED SAFES. WHILE UNBOXING BE SURE TO HAVE A SECOND PERSON HOLD AND STABILIZE THE SAFE TO KEEP IT FROM TIPPING, CAUSING INJURY, AND/OR DAMAGE TO THE SAFE AND SURROUNDING STRUCTURES.

Remove the packaging. If your safe is still on shipping feet you can simply lift the box up and off the safe once the strapping has been removed. If your safe does not have shipping feet you will need to carefully remove the box, ensuring not to damage the safe and/or injure yourself. You will want to have someone stabilize the safe when removing the cardboard and other packing material from underneath the safe.

INSPECTION

• Make sure to inspect your safe for shipping damage before accepting delivery.
• If you find any damage, please contact the delivery company (or carrier) immediately.
• Any damage not noted upon delivery must be reported within fifteen (15) days or there will be no recourse. Any noted damage at the time of delivery must be resolved with the delivery company and/or retailer. Shipping damage is not warrantable by SA Consumer Products.

OPENING YOUR SAFE

1. Locate the backup keys and single handle spoke inside the plastic bag hanging on the front of the safe.
2. Install the single handle spoke by inserting into one of the threaded openings and twisting clockwise.
3. Locate the keyhole on the safe door. Insert and turn the backup key clockwise from 9 to the 1 o’clock position to unlock.
4. Turn the handle clockwise until the safe door opens. Once open, turn the handle back to its starting position so the bolts are extended. Remove key.

PROPER PLACEMENT AND MOVING OF SAFE

WARNING: SAFES ARE VERY HEAVY AND AWKWARD TO HANDLE. PLEASE USE THE UTMOST CARE IN MOVING THE SAFE. UTILIZING A TRAINED PROFESSIONAL WITH PROPER MOVING EQUIPMENT IS HIGHLY RECOMMENDED.
The location of the gun safe is very important and the utmost care should be taken during this consideration.

1. To maximize the fire protection of your safe, we recommend you place the safe inlower levels in your home where fire temperatures are lower and away from highly combustible materials.
2. To maximize burglary protection and stability, securing the safe to the floor is recommended.
3. SA Consumer Products recommends that you store your safe in a closet, office, basement, bedroom or any other location that is convenient for you but out of direct line of sight from prying eyes.
4. The location of the gun safe is very important.
5. Using a dolly capable of supporting the size and weight of your safe, move the safe to your desired location. Please take all necessary precautions to protect and prevent any damage to your flooring.
6. HELPFUL TIP: TO DETERMINE WHETHER YOUR SAFE WILL MAKE IT THROUGH DOORWAYS, STAIRS, OR CORNERS, TAKE THE EMPTY SAFE BOX AND SEE IF IT WILL FIT ALL THE WAY THROUGH TO ITS FINAL LOCATION.
7. The safe should be installed adjacent to a side wall with minimal space on eitherside of the safe. Wherever possible, the safe should be flat against the wall and floor. Remove the baseboard and/or wall trim if necessary.
8. Always ensure the safe is in an isolated and dry area. Never place the safe in direct contact with a wet floor. When installing your safe on a concrete floor, use of a moisture/protective barrier is highly recommended. Failure to do so, or exposing the safe to chemicals or other adverse environments, may void the warranty.
9. If your safe seems unlevel, you may need to shim the bottom of the safe to prevent the door from swinging open too quickly, or closing on itself.

KEEPING YOUR SAFE DRY

We recommend placing a moisture/protective barrier between your safe and concrete floor to prevent any moisture, mildew and rust damage the safe. Installing your safe in a place with climate control (heat in the winter and cooling in the summer) is highly recommended. In areas of high humidity or frequent temperature fluctuations (garages) it is recommend to take appropriate precautions to ward against moisture damage. We strongly encourage the use of an internal dehumidifier and/or desiccants to protect your contents from rust or mildew. Internal dehumidifiers should not be in direct contact with the side or back walls.

SECURING YOUR SAFE

WARNING : YOUR SAFE IS DESIGNED TO SUPPORT ITSELF WHEN THE DOOR IS OPENED. HOWEVER, CAUTION SHOULD BE USED TO AVOID TIPPING. WHILE SECURING YOUR SAFE BE SURE TO HAVE A SECOND PERSON HOLD AND STABILIZE THE SAFE TO KEEP IT FROM TIPPING, CAUSING INJURY, AND/OR DAMAGE TO THE SAFE AND SURROUNDING STRUCTURES. FAILURE TO DO SO WILL COMPROMISE THE SAFETY, SECURITY, AND WARRANTY OF THE SAFE.

TOOLS NEEDED TO BOLT SAFE TO A CONCRETE SURFACE

• DRILL/HAMMER DRILL
• DRILL BIT -1/2″ ( for installing into concrete with provided hardware)
• WRENCH/ 11/16″ (17MM) SOCKET
• HAMMER

1. Use the hardware provided or consult your hardware retailer for fastening hardware for your particular mounting surface.
2. Open your safe door and locate and remove the four black caps on the safe floor. This will provide access to the factory drilled bolt down holes.
3. To secure your safe to the floor it will first be necessary to drill pilot holes in the floor surface.
4. Drill the appropriate diameter and depth of pilot holes based on the type of hardware being used and the type of floor surface. For the hardware provided (concrete floor installation) we recommend using a hammer drill and 1/2″ concrete drill bit to drill holes the four corresponding in the concrete floor.
5. Insert and drive the plastic anchoring plugs into the pilot holes. You may need to use a hammer to fully insert the plugs into the pilot holes.
6. Secure the safe, by threading all 4 anchor bolts through the factory drilled bolt down holes in the bottom of the safe and ratcheting down tight.
7. Make sure the metal washer sits on top of the rubber washer. Tighten the bolt to compress the rubber washer between the safe and metal washer. Failure to do so will allow water to enter the safe in the event of a flood.
8. Replace the four black caps onto the floor of the safe.

LOCK FACE INSTALLATION

1. Remove lock face from box located inside the lower door safe.

2. The lock face requires lx9V alkaline battery. Locate the battery compartment on the back of the lock face.
   Insert the battery in the proper orientation. Lock face will beep when batteries are successfully installed.
   WARNING : The batteries must be inserted with the correct polarity. Exhausted batteries must be removed from the product and discarded safely. Do not use rechargeable (nickel – cadmium) batteries.

3. Plug lock face cable into the back of the lock face. The cable will only be able to fit one way.

4. Align the lock face to the backer plate. Turn clockwise until you feel the lock face click into place. Once the lock face has been installed, locate the remaining handle spokes inside of the safe.
   Insert each individual spoke into a threaded opening and turn clockwise to install.

LOCK FACE SECURITY CODE SETUP

Important : It is necessary to reprogram your safe with a new security code you have personally selected to provide maximum household security. Be careful in choosing your new security code, you’ll want to be sure that you can operate the unit quickly without making an error.

1. Swipe finger(s) across the keypad to “wake up” and activate the lockface. Two random numbers will illuminate when the lock face wakes up. Individually press both of the two numbers, in any order, to allow full access to the keypad.Insert the factory preset code of (1-5-9-#). This will unlock the safe in a DEFAULT MODE. (DO NOT use this code while securing items in your safe)
2. Inside of the safe door, locate the small brass cap. Unscrew and remove the cap, you will now see the red reset button. Press and release the reset button. You will hear a beep. The yellow (left) light on the lock face will illuminate indicating you are now in programming mode.
3. While the yellow (left LED) is illuminated, enter your new 3 to 8-digit security code NEW 3-8 followed by [*] lock face will beep twice indicating successful programming
4. While the safe door is still open, confirm your newly entered security code. Wake up the keypad by swiping the keypad with your finger(s). Enter the two random numbers. Now enter the 3-8 digit code followed by (#). If successful you will hear a beep and the green light will illuminate, allowing you to open the safe.

Always remember to SWIPE your finger(s) across the surface of the keypad to wake the keypad before attempting to enter your security codes. Simply touching the keypad may not trigger a sensor point on the key pad to activate keypad properly. Note: Do not shut the safe door until you have confirmed your new security code at least 3 times, ensure your code has been saved and you can open the door successfully. If the code fails, the yellow (left) light will flash and beep. Repeat the steps above until successful.
WARNING : If the incorrect security code is entered 3 times you will have an automatic lockout for 30 seconds before you can enter your code again. If 3 additional failed attempts are made, the lock face will lockout for 5 minutes. Leave batteries in to go through lockout cycle. If batteries are removed the timer will restart zero.

LOCKED OUT OF YOUR SAFE

In the event you have forgotten the security code your primary action will be to use your backup keys in order to gain access to your safe and follow the Lock Face Security Code Setup instructions, starting at step 5. If you have lost your backup keys, you will need to contact customer service at the number below. Proof of purchase is required to obtain keys.

INTERIOR LIGHTING

This safe comes with motion activated interior lighting installed. When the safe is plugged into a power source and USB connection of the lighting system is plugged into the internal power receptacle, the lighting will function automatically. When powered on, motion will activate the system and turn on the interior light which will remain on for 30 seconds. Lights will be activated for an additional 30 seconds upon sensing any movement.

LOW BATTERY WARNING

• This lock face is equipped to alert you when the batteries are low by illuminating the red light (center) when any number is pressed on the keypad. Please replace batteries immediately when receiving this warning.
• Always test the batteries when installing or replacing. If the red light comes on when a button is pressed you know the batteries are not fully charged

QUIET MODE

• By activating the lock face quiet mode, the safe will no longer make audible sound when interacting with safe, allowing for silent access.
  • To mute the lock face, enter the code [* 6 3 3).
  • To turn the sound back on, enter code[* 6 6).

LOADING YOUR SAFE

1. Store documents or heat sensitive items in the bottom of the safe for greatest protection against fire damage.
2. Store ammunition separately from valuables.
3. Do not put anything in your safe that will put pressure against the door when it is closed.
4. Store heavier items either on the floor of the safe, or away from the middle of the shelves.
5. When placing guns into your safe, make sure they rest securely against the cutouts provided in the gun racks to prevent accidental tipping when the door is closed.

MAINTAINING HINGES AND INTERNAL MECHANISMS

The hinges and internal locking mechanism are permanently lubricated, thus needing no maintenance. Opening the door panel of your safe may void your warranty. Always consult our customer service experts prior to doing so.

LIFETIME WARRANTY

• SA Consumer Products. Inc. will repair or replace. at their sole discretion. any Sports Afield Gun Safe damaged by fire. forced entry. forced attack or natural flood for the lifetime of the original owner.
• SA Consumer Products. Inc. will repair or replace. at their sole discretion. any Sports Afield Gun Safe with defective parts. paintor lock for the lifetime or the original owner.
• If SA Consumer Products. Inc. deems a replacement safe is to be sent. they will pay the freight costs to ship the replacement safe to the original owner.
• This lifetime warranty is limited to the safe and expressly excludes any loss associated with the contents of the safe.
• SA Consumer Products. Inc. reserves the right to receive full evidence of your misfortune. such as a police report and/or homeowners statement of coverage. This warranty is not valid outside of the United States and Canada.
• Proof of registration and copy of sales receipt must be on file at the time of claim. Visit our website at www.saproducts.com to register your safe.
• Lifetime warranty only applies to the original owner of the safe.
• SA Consumer Products. Inc. shall only be responsible and liable when the safe is used in compliance with the directions specified in your new Sports Afield Safe Owner’s Manual.
• SA Consumer Products. Inc. requires that specific guidelines be followed for repair. The safe will be repaired in-home if possible (to include parts and labor); however. if factory replacement is necessary (at SA Consumer Products. lnc.·s sole discretion). the replacement will be shipped freight prepaid. curbside delivery.
• This warranty is inclusive and is in lieu of any and all other warranties. express or implied. Specifically excluded are the warranties of merchantability and fitness for a particular purpose.
• This warranty is limited to the safe itself and/or its value and does not include consequential damages of any kind including. but not limited to. the contents in and of the safe.

Distributed by: Costco Wholesale Corporation 999 Lake Drive Issaquah, WA 98027 USA
www.costco.com
MADE IN CHINA

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>