CNBINGO ‎DS-101JL Smart Touch Light Switch Instruction Guide

CNBINGO ‎DS-101JL Smart Touch Light Switch

Specifications

• OPERATION MODE: ON-OFF
• CURRENT RATING: 1.8 Amps
• OPERATING VOLTAGE: 240 Volts
• CONNECTOR TYPE: Screw
• BRAND: CNBINGO
• MODEL: DS-101JL
• SWITCH STYLE: Touch Switch, Pushbutton Switch
• MATERIAL: Tempered Glass, Fire-resistant PC, Brass
• ITEM DIMENSIONS L X W X H: 8.6 x 8.6 x 3.6 centimeters
• CIRCUIT TYPE: 1-way
• PLUG PROFILE: Wall Mount
• WIFI STANDARD: 2.4GHz network (not 5G)
• INPUT VOLTAGE: 220V – 240V, AC 50Hz
• LOAD POWER: 10-400W/gang INC；5-200W/gang LED
• SMART LIFE APP: IOS / Android

Introduction

With the CNBINGO WiFi Light Switch, a Glass Plate and Screws are included. To finish the wiring and pairing, you can adhere to the detailed instructions. When pairing, it ONLY connects to 2.4GHz WiFi networks, although it may be operated over mobile data (2/3/4G or 5G). There is no need for a hub. Pressing and holding on the glass panel’s front until it begins to flash will turn on the CNBINGO Touch Switch. Then, connect it to the Smart Life App by following the on-screen instructions. It Utilizes Google Home and Alexa to enable convenient voice control of the light while your hands are busy.

When you’re not home, you may use your smartphone to remotely adjust the lights to give the impression that someone is home, deterring intruders from breaking in. It is Waterproof and safer than push buttons, tempered glass panels avoid electric shock even when touched by damp hands. Strong/weak blue backlight that, when touched, clearly indicates the on/off status and makes it simple to discover in the dark; has no effect on sleep. Even when short- circuited, fire-resistant PC material does not catch fire. It Secures your home.

HOW A SMART SWITCH WORKS WITHOUT A NEUTRAL WIRE

Make R1 the ideal resistance to build a smart switch that doesn’t require the neutral loop. To prevent the light bulb from turning on when the switch is off, R1 must sufficiently limit the current. At the same time, it must permit adequate current flow for the switch to recharge.

HOW TO REPLACE A WALL SWITCH WITH A SMART SWITCH

• Disconnect the power. When dealing with electrical lines, your main focus should always be safety.
• Old light switch removed. Take off the screws.
• Put in a smart switch. In essence, replacing the smart light switch is the opposite of taking out the old switch:
• Put the smart switch in place.

HOW A SMART WIFI LIGHT SWITCH WORKS

An old light switch is swapped out for a smart one. You can remotely or using voice assistants turn that switch on and off once you connect it to your home’s Wi-Fi network. Your light bulbs only need to be the ones linked to that switch; they don’t even need to be smart bulbs.

HOW A TOUCH LIGHT SWITCH WORKS

The idea behind how touch bulbs operate is capacitance, or how much charge an object can hold. Capacitors, which are employed in circuits to smooth voltage fluctuations or tune circuits like radio receivers, store variable quantities of charge.

HOW TO FIX UNRESPONSIVE SMART LIGHT

• Switch the light on for three to five seconds before turning it off for the same amount of time. Turn it back on after several repetitions of this action. The bulb blinks if the reset was successful.
• OFFSET the lightbulb.
• Relaunch Discovery.
• Light the bulb.

Frequently Asked Questions

If there is no neutral wire, what should one do?

There are three basic alternatives if you don’t have a neutral wire: Install a neutral wire. A smart light switch without a neutral wire is the best option. Use intelligent light bulbs rather than intelligent light switches.

Can I use a neutral wire for the ground?

A ground is not an impartial time. The washer’s chassis acting as a conductor for current flow is the absolute last thing you need. If the neutral and ground in your home are bonded, then there should only be one connector for them, and that is in the circuit breaker panel.

Is there a neutral wire on every switch?

Normal rocker and toggle switches won’t be wired with a neutral. It is probably not a neutral wire if you do discover a white wire attached to a rocker or toggle switch. You can find out which wire this is by reading our support article on common switches.

Is there someplace I can extract a neutral wire from?

The neutral wire from another circuit cannot be taken. The return for each hot wire’s equivalent neutral wire. The neutral wire could become overloaded if you “borrow” a neutral from another circuit (overheat, fire risk).

Why are neutrals not required for switches?

Switches only require two wires: hot and switched-hot; they do not require neutrals. Unless you’re dealing with a smartswitch, which accepts neutrals but still requires you to account for a switched hot. Additionally, although red is a typical switched-hot hue, it would never, ever, ever, ever be utilized for neutral.

Is a neutral wire required?

As you can see, the neutral line is vital to the electrical system in your house. Without it, there wouldn’t be a circuit for energy to travel through so that it could make a full circuit back to the power source.

Does the code require neutral wires?

A neutral wire is required at all switch sites. The fundamental reason for implementing this national electrical code was to account for anticipated future usage. An additional neutral wire must be provided to electronic switches since they need a modest quantity of steady electricity.

Should I connect the neutral wire?

Except in extremely uncommon circumstances, a box must have all of its neutral wires connected. If a neutral isn’t connected to a fitting, the current won’t return to the supply and won’t function. Three may be connected in one connector, three in another, and then a link between the two could be created.

Does a capacitor work with a smart switch?

For non-neutral switches to be fitted on your fans or lights, a capacitor is required. One of the fans or lights that is connected to the same smart switch just has to have a capacitor installed. You will need to open up your lights/fans and search for the wire configuration in order to connect a capacitor.

How can I tell if the switch on my lamp has a neutral wire?

Snapping off or unscrewing the existing switch’s wall plate will allow you to remove it. Remove the present switch by unscrewing it from the electrical box and slowly removing it until the wires attached to it are visible. If you notice a white wire or several of them, you should have neutral wiring.

Video

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>