CNBINGO WPS-641 700W Dimmer Touch Light Switch Instructions

June 14, 2024
CNBINGO

CNBINGO WPS-641 700W Dimmer Touch Light Switch

CNBINGO WPS-641 700W Dimmer Touch Light Switch

Introduction

Thank you for purchasing our Touch Light Switch.

This manual will ensure and comfortable use. Please read the instruction carefully before usage.
QR-Code

TECHNICAL DATA

Dimensions 86 x 86 x 35 mm
Voltage 110 – 240  V AC / 50 – 60 Hz
Load Power: 3 -70 0w/gang,70 0 W total
Energy Consumption 0.05w
Operating Temperature -20 °C to+ 70°C
Capacity Allowance -15% to +10%
Humidity Range 10% to 9 3%
Distance between the screws 58 – 62 mm
Mechanical Lifespan 100,000 switching cycles

Technical Data

ATTENTION

  • Never try to mount the light switch on your own. Only have the installation carried out by a trained specialist!
  • The light switch cables must be connected exactly as in the following graphic.
  • Make sure that all cables are sufficiently isolated.
  • Make sure that there is no voltage and the electric power is turned off by powering off the fuse.
  • The diameter of the flush-mounted box must be at least 72mm and the depth must be at least 65mm.
  • Do not remove the protective film of the touch surface that is located inside the light switch (underneath the cover) to prevent loss of sensitivity.
  • The light switch does not work with lamps that have inductive ballasts.
  • Only after the glass plate has been installed you can turn on the power last. Or the switch will not work properly. If test without glass ,switch will remember the distance between the pad and figure. And cannot work well after put glass on.

USING THE SWITCH

  • If touch the circle and release quickly, work as on or off.
  • Touch and hold the circle area to dim up. Release and hold again to dim down ( up & down alternating ).Dimmer switch has memory function. For example, if the lights 60% brightness when off, it will be still 60% bright when turn on again.

HOW TO USE

How To Use

Click The Middle Button To Turn On/Off
Hold The Right Button To Dim
Hold The Left Button To Brighten

WIRING

  • 1 gang 1 way wiring

  • 2 gang 1 way wiring ( only one led adapter ok )

Wiring of the Led Adapter

  • LED adapter or capacitor necessary when lamp flash/flicker, especially for small wattage lamp.
  • One switch only needs one led adapter.
  • The Led adapter resistance is 15K ohm, made from ceramics, can endure more than 800degress, safe and cannot cause fire.
    Wiring of the Led Adapter
    Led Adapter connected .at both sides of the bulb
    Wiring of the Led Adapter
    Led Adapter connected with downlight with led driver

MOUNTING

Before the light switch can be mounted you have to power off the fuse so that there is no electric power.

  • Remove the glass panel of the switch by using a screwdriver.
    Mounting

  • Unscrew the screws slightly and connect the cables as shown in the circuit diagram. Tighten the screws again and make sure that no cables are loose, and the isolation of the wires reaches the housing.
    Mounting

  • Mount the light switch to your flush -mounted box by using the delivered screws.
    Mounting

  • Hook the glass panel back into the housing and press it until you hear a click and the panel is firmly seated on the housing.
    Mounting
    Make sure that the panel is mounted to the housing the right way around. The cable connections should point upwards and the groove should be on the bottom of the glass panel.

  • Now, the fuse can be powered on again.
    Mounting

TROUBLESHOOTING

  • The lamps to be used must have a minimum power of 3 W.
  • The switch automatically detects if there is a load. If no light at all or a defect light is connected, the switch cannot be turned on.
  • If the switch has a malfunction during use, you can reset it by disconnecting the power supply for approximately 10-15 minutes.

HINTS

  • Protect the device from humidity and moisture.
  • Do not use near water.
  • Avoid bumps or falls.
  • Do not try to modify the unit or to repair it by yourself.
  • Clean only with a dry cloth. Do not use chemical substances.
  • Do not dispose of the device in household waste at the end of its life cycle. Only dispose at specially-designated collection locations, recycling depots or disposal companies.

APPLICABLE LAMPS

  • Min.3W dimmable triac led lamps; incandescent lamps.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals