YESWE i4 Spy Camera 1080P Wi-Fi Hidden Camera Clock User Manual
- May 15, 2024
- YESWE
Table of Contents
i4
User Manual
i4 Spy Camera 1080P Wi-Fi Hidden Camera Clock
RESET BUTTON
Find a pen or any small stuff to keep pressing the Reset button for about 5-10 seconds until the blue and red lights go off together. The camera will be back to original Settings.
When do we need to Reset the Camera
A: If the camera fail to connect to your home WiFi network, Please Reset the
camera.
B: If you can’t find the camera’s Wi, on your phone Wifi st Please Reset the
camera.
C: If you forget the camera’s password that you set, Please Reset the camera.
(Camera Default Access Password : 6666 )
Set up instruction
Step 1: Plug the camera into power
Step 2: Download the App “LookCamPro’.
Step 3: Open the App to add the camera.
Press the + to select the method 1 and then go to your phone Wi-Fi setting to
connect the camera Wi-Fi: TUT-XXXXXX-XXXXX 
Note 1: Please do not worry
about the camera Wi-Fi says ‘Internet may not be available” or “unsecured
network’ Just go back to the App and continue to set up.
Note 2: If the camera Wi-Fi TUT-XXXXX-XXXX does not show up on your phone
Wi-Filist. You need to reset the camera.
Step 4: Go back to the App and connect the camera to your home Wi-Fi
network so that you can remotely view the camera. 
Note 1: After you connected the camera Wi-Fi and retumed to the
app, there will be a page with all Wi-Fi network pop up automatically.
You need to select your home Wi-Fi <please make sure to select the 24G signal>
and put in the correct password.
Note 2: If the Wi-Fi page does not pop up, do not worry, you can connect
the camera to your home Wi-Fi manuall.
Note 3: After you connect the camera to your home Wi-Fi
network, please close the app and wait for 5 minutes to come back, the camera
should be online if your password is correct
Note 4: If the camera did not come back online after 5 minutes, that
means you might put the wrong Wi-Fi password or did not select the 24G signal.
Now you need to reset the camera and start it over.
App Instruction
Motion Detection Set up
Go to menu settings and then go to alarm setting to turn on the motion
detection. 
Questions & Answers
Q, When the first time I try to connect the camera with my phone, but I could not find the camera Wi-Fi on my cellphone Wi-Fi settings, what should I do?
A, Anytime when you try to connect to the camera, and you are not able to find the camera Wi-Fi on your cellphone Wi-Fi list. You need to reset the camera and then wait for 1 min then the camera Wi-Fi will show up.
Q, How to reset the camera?
A, The reset button is on the back of the camera with a letter “RST, it is right beside to the on/off switch. Get a pen to keep pressing it for 5-10 seconds. After that, inside the blue and red light will be off and on again after few seconds, that means the camera is successfully reset to the original setting.
Q, How does the SD card work?
A, This camera works with micro SD card 32G-128G. Once you inert the SD card into the camera, the camera will start recording automatically.
Q, How to set the correct time on the clock
Q, How long the battery work after it is fully charged.
A, Not for so long, about 1 hour, if you want this camera work for 24/7, you should keep charging it. After you plugged in, the camera also can work without battery.
Q How does this camera recording work?
A: There are 3 parts of recording for this camera. 1, Live View Recording: When you are in the live-viewing page and try to record some clips, then you need to press the record button to start recording, but please do not leave or quit the App, you need to stay on the live-viewing page to keep it recording and then press stop to finish recording, The file will be saved on the app local videos. Ifyou leave the app, the recording willbe lost 2,5 Card Recording: If you want the camera to keep recording 24/7 non-stop, then you need to putin a micro SD card that up 10 128GB, the camera will keep loop- recording to the SD card. No matter the camera s with wifi or without wif 3, Motion Detection Recording: If you want the camera to record only when there is a movement, then you need to gotothe App setting to set up the motion detection first and then go to the SD card settings to set the record mode to. “record when alarm” that is how you set the motion detection record.
Q, Why my camera went offline as soon as left the house?
A: After you connect the camera WiFi TUTXXXXXX and go to the app, camera will be showing online, remember, the set up is not finished yet, a ot of people get here and think set up is done because the camera is showing online, but now the camera is only connecting with your cellphone,it’ s not on interetyet, you' re not able to monitor it remotely. Onelast thing we need to do, we need to connect the camera to your home WiFi network, after the camera successfully hooked up to your home WiFi, the set up is done.
You need o go tothe App settings and then go to the Wifi settings to find your home Wii network and select the 2.4G Wii signal at that page and put in the correct password. After putting in the password then please wait for 3 minutes for the camera to come back online.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>