CNBINGO 2 Pack Way Touch Light Switch Instruction Manual

CNBINGO 2 Pack Way Touch Light Switch

Thank you for purchasing our Touch Light Switch. This manual will ensure smooth and comfortable use. Please read the instructions carefully before usage.

TECHNICAL DATA

ATTENTION

• Never try to mount the light switch on your own. Only have the installation carried out by a trained specialist!
• The light switch cables must be connected exactly as in the following graphic.
• Make sure that all cables are sufficiently isolated.
• Make sure that there is no voltage and the electric power is turned ” off by powering off the fuse.
• The diameter of the flush-mounted box must be at least 72mm and it must be at least 65mm.
• Do not remove the protective film of the touch surface that is located on the light switch (underneath the cover) to prevent loss of sensitivity.
• The light switch does not work with lamps that have inductive ballasts.
• Only after the glass plate has been installed you can turn on the power last. Or the switch will not work properly. If tested without glass, the switch will remember the distance between the pad and the figure. And cannot work well after putting the glass on.
• 2way switch can only work together with our same type of 2way switch, and cannot work together with mechanical 2way switches or switch from another plant.

USING THE SWITCH

Wiring

Wiring of the Capacitor

• LED adapter or capacitor is necessary when lamp flash/flicker, especially for small wattage lamp.
• One switch only needs one Capacitor

Synchronizing One 2-Way Switch with the Other 2-Way Switch

• The switch has a 2-way function only after synchronizing it with the other 2-way switch. If not synchronized, only work as 1way.
• Synchronize only L1 to L1, L2 to L2, L3 to L3, cannot L1 to L2, L2 to L3 or L1 to L3.

Steps 1

• When the 2way switch is off, touch the desired gang center circle and hold on for 4 seconds min.
• The backlight will flash, and then release your finger.
• Now the switch is in matching mode and ready for programming (please finish the program in 10 seconds).

Step2:

• Touch the desired gang center circle ( at the corresponding position as the Step1 switch) on the other 2way switch.
• The backlight will stop flashing and become constant blue. Synchronizing success.

Cancelling 2way Function

• When 2way switch off, touch 2way function Synchronizing Cancelling 2way function SynchronizingWhen 2way switch off, touch and hold on for 5seconds min.
• The backlight will flash, then release your finger.
• Touch and hold on again for seconds min., then the backlight will stop flashing and become constant blue.
• Cancelling success.

MOUNTING

Before the light switch can be mounted you have to power off the fuse so that there is no electric power.

• Remove the glass panel of the switch by using a screwdriver.
• Unscrew the screws slightly and connect the cables as shown in the circuit diagram. Tighten the screws again and make sure that no cables are loose, and the isolation of the wires reaches the housing.
• Mount the light switch to your flush-mounted box by using the delivered screws.
• Hook the glass panel back into the housing and press it until you hear a click and the panel is firmly seated on the housing.
• Make sure that the panel is mounted to the housing the right way around. The cable connections should point upwards and the groove should be on the bottom of the glass panel.
• Now, the fuse can be powered on again.

TROUBLESHOOTING

• The lamps to be used must have a minimum power of 3 W.
• The switch automatically detects if there is a load. If no light at all or a defective light is connected, the switch cannot be turned on.
• If the switch has a malfunction during use, you can reset it by disconnecting the power supply for approximately 10-15 minutes.

HINTS

• Protect the device from humidity and moisture.
• Do not use near water.
• Avoid bumps or falls.
• Do not try to modify the unit or repair it by yourself.
• Clean only with a dry cloth. Do not use chemical substances.
• Do not dispose of the device in household waste at the end of its life cycle.
• Only dispose of at specially designated collection locations, recycling depots, or disposal companies.

Touch 2-Way Switch

Documents / Resources

| CNBINGO 2 Pack Way Touch Light Switch [pdf] Instruction Manual
2 Pack Way Touch Light Switch, 2 Pack, Way Touch Light Switch, Touch Light Switch, Light Switch, Switch
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>