MEAN WELL NPB-1200 Series 1200W High Reliable Ultra Wide Output Range Intelligent Battery Charger Instruction Manual
- June 10, 2024
- MEAN WELL
Table of Contents
- 1.Manual setting
- 2.Programmable charging curve
- 3. Auto Ranging for Charging (Default non-Auto ranging)
- 4.Auto Derating function
- 5.CANBus communication interface
- 6.Charger OK Signal
- 7.Battery Full Signal
- 8.Remote ON-OFF Control
- 9.Temperature compensation(3 stage only)
- 10. DC Output Side LED Indicators & Corresponding Signal at Function
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
MEAN WELL NPB-1200 Series 1200W High Reliable Ultra Wide Output Range Intelligent Battery Charger Instruction Manual
Features
Applications
Description
SPECIFICATION
Function Manual
1.Manual setting
1.1 2 or 3-stage selectable via DIP S.W on panel
1.2 Charging curve can be adjustable via DIP S.W on panel
◎ Suitable for lead-acid batteries (flooded, Gel and AGM) and Li-ion batteries
(lithium iron and lithium manganese).
◎ Suitable for lead-acid batteries (flooded, Gel and AGM) and Li-ion batteries
(lithium iron and lithium manganese).
※ The default curve is programmable, whereas other pre-defined curves can be activated by the means of the DIP S.W; This series provides 2 or 3 stage charging curve please refer to the table below and the Mechanical Specification.
2.Programmable charging curve
Charging Curve can be set via SBP-001 with computer
Step 1
Hardware configuration
Step 2
Connect to software for setting
※ Function Description:
SBP-001 is a programmer, particularly for MEAN WELL’s various programmable
battery charger models to program the parameters of charging curves, such as
the 2 or 3 stage selectable, Constant current (CC), tapper current(TC),
Constant voltage (CV), float voltage (FV),Charging time out and so on, to
accommodate the diversified battery specification in industry. With the design
accounting for simplicity and convenience, users can easily configure MEAN
WELL’s programmable battery chargers with SBP-001 programmer and the computer;
all of the setups are able to be finished easily by the means of the specific
software. Note:(1) Tapper current(TC) default is 10%, can be fine tuned from
2% to 30% by SBP-001 with computer or CAN Bus Interface. (2) Please contact
MEAN WELL for more details.
※ Software Interface:
3. Auto Ranging for Charging (Default non-Auto ranging)
※ Function Description:
a. NPB-1200 has built-in auto ranging mode.
(Note this mode is set to OFF by factory default and is suitable for lithium
batteries with BMS only)
b. When operating in auto ranging mode , NPB-1200 will automatically detect
the voltage of battery that is connected and adjust charging voltage
accordingly. It will not start charging unit appropriate battery voltage is
detected.
c. While under auto ranging mode, NPB-1200’s built-in MCU will adjust charging
voltage. There is no potentiometer for voltage
adjustment on the front panel.
d. While under auto ranging mode, the charging current can be adjusted between
50~100%.
(The charging current can not be adjusted via potentiometer while not
operating in auto ranging mode)
※ When using the auto ranging charging curve function, please pay attention to the following:
- Default factory setting is OFF via DC output side DIP S.W, Follow steps A1~A6 below to enable the setting.
- Auto ranging function should use together with Lithium batteries and BMS (Battery Management System).
- Do not exceed the output voltage and current ranges as specified in the NPB-1200 specifications (please refer to page 2).
4.Auto Derating function
※ Covered by over temperature protection, auto de-rating function works under
operation either in charging curve (2 or 3 stage) or under control by
communication protocol(CAN Bus).
T1(Typ.): Maximum ambient temperature of 100% output current. T2(Typ.): T1+5.
5.CANBus communication interface
CAN Bus 2.0B version, Can control, setting and monitoring that including output charging voltage, output charging current,internal temperature and DC output ON/OFF……and so on, please refer to the user manual for more details.
6.Charger OK Signal
Charger OK signal is a TTL level signal. The maximum sourcing current is 10mA.
7.Battery Full Signal
Battery full signal is a TTL level signal. The maximum sourcing current is 10mA.
8.Remote ON-OFF Control
The NPB-1200 can be turned ON/OFF by using the “Remote Control” function.
9.Temperature compensation(3 stage only)
Temperature compensation function to prolong battery life for lead-acid
batteries. Temperature compensation range is 0 ~ 40. The battery temperature
sensor comes along with the charger can be connected to the unit to allow
temperature compensation of the charging voltage.
If the sensor is not used, the charger works normally.
10. DC Output Side LED Indicators & Corresponding Signal at Function
Pins
Mechanical Specification
※ Intelligent Battery Charger model
Note1: Non-isolated signal, referenced to [GND(signal)].
Note2: Isolated signal, referenced to GND-AUX
Accessory List
※ NTC Sensor and Remote Control mating along with NPB-1200 (Standard
accessory)
INSTALLATION MANUAL
Please refer to : http://www.meanwell.com/manual.html
File Name:NPB-1200-SPEC 2021-11-29
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>