RYOBI R18ALP 18V ONE+ Project Light Instruction Manual

RYOBI R18ALP 18V ONE+ Project Light

Product Information

The R18ALP project light is designed for general illumination of most work area spaces. The product is not intended for use in wet conditions or for any other purpose. Safety, performance, and dependability have been given top priority in the design of this product. All repairs should be performed by an authorised service centre. The product features a light source that shall only be replaced by the manufacturer or his service agent or a similar qualified person. It is important to use the recommended battery pack and charger. Do not attempt to use another battery pack as it could cause damage to the product and possibly lead to an explosion, fire or personal injury. Also, do not disassemble the product, and avoid placing it or the battery pack near fire or heat. The battery safety warnings indicate that the tool, battery pack or charger should never be immersed in fluid or have fluid flow inside them to avoid short circuits. When transporting lithium batteries, follow all special requirements on packaging and labelling, and make sure that no batteries come in contact with other batteries or conductive materials while in transport. Do not transport batteries that are cracked or leaking.

Product Usage Instructions

Before assembling, operating, and maintaining the R18ALP project light, it is essential to read the instructions in the manual carefully. The product is designed for general illumination of most work area spaces, but it should not be used in wet conditions or for any other purpose. To ensure safety while using the product, avoid disassembling it or placing it or the battery pack near fire or heat. Remove the battery pack before starting any work on the product. Do not stare at the light source as it can cause harm to your eyes. When cleaning plastic parts, avoid using solvents as most plastics are susceptible to various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, carbon dust, etc. Do not let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic parts as they can damage or weaken the plastic, resulting in serious personal injury. When transporting lithium batteries, follow all special requirements on packaging and labelling, and ensure that no batteries come in contact with other batteries or conductive materials while in transport. Do not transport batteries that are cracked or leaking. Finally, when disposing of the product, do not dispose of it with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

IMPORTANT!
It is essential that you read the instructions in this manual before assembling, operating, and maintaining the product. Subject to technical modifications. Safety, performance, and dependability have been given top priority in the design of your project light

OVERVIEW

INTENDED USE

The project light is designed for general illumination of most work area spaces. Do not use the product in wet conditions. Do not use the product for any other purpose

PROJECT LIGHT SAFETY WARNINGS

• The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person.
• Use only with recommended battery pack and charger. Any attempt to use another battery pack will cause damage to the product and could possibly explode, cause a fire, or personal injury.
• Do not disassemble the product.
• If wrapped or in contact with fabrics, the lens can produce sufficient heat to melt some fabrics. To avoid serious personal injury, never allow the lens to come in contact with anything.
• Do not place the product or battery pack near fire or heat. This will reduce the risk of explosion and possible injury.
• Remove the battery pack before starting any work on the product.
• Do not store the product in a damp or wet location, or in a location where the temperature may reach or exceed 40°C. For example, inside sheds, vehicles, or metal buildings in the summer

BATTERY SAFETY WARNINGS

To reduce the risk of fire, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack or charger in fluid or allow a fluid to flow inside them. Corrosive or conductive fluids, such as seawater, certain industrial chemicals, and bleach or bleach-containing products, etc., can cause a short circuit

TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national provisions and regulations. Follow all special requirements on packaging and labelling when transporting batteries by a third party. Ensure that no batteries can come in contact with other batteries or conductive materials while in transport by protecting exposed connectors with insulating, non-conductive caps or tape. Do not transport batteries that are cracked or leaking. Check with the forwarding company for further advice.

MAINTENANCE

• Use only original accessories and spare parts. Should components need to be replaced which have not been described, please contact an authorised service centre. All repairs should be performed by an authorised service centre.
• Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, carbon dust, etc.
• Do not at any time let brake fluids, gasoline, petroleumbased products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury.

SYMBOLS ON THE PRODUCT

SYMBOLS IN THIS MANUAL

INSTALLATION INSTRUCTIONS

PRODUCT SPECIFICATIONS

Project light

• Model R18ALP
• Voltage 18 V
• LED lamp(Watts maximum) 10 W
• Light output (Lumens)
• High brightness level 900 Lum
• Medium brightness level 600 Lum
• Low brightness level 100 Lum
• Correlated colour temperature (CCT) 5700 K
• Weight – excluding battery pack 0.5 kg

BATTERY

Compatible battery pack (not included)

• RB18L13
• RB18L15
• RB18L15A
• RB18L15B
• RB18L20
• RB18L20A
• RB18L25
• RB18L25A
• RB18L40
• RB18L40A
• RB18L50
• RB18L50A
• RB18L60A
• RB18L90A
• RB1815C
• RB1820C
• RB1825C
• RB1840C
• RB1840X
• RB1850C
• RB1850X
• RB1860X

Imported by:
Techtronic Industries Australia Pty Ltd 31 Gilby Road, Mount Waverley, VIC 3149 Melbourne, Australia Techtronic Industries N.Z. Limited Unit C, 70 Business Parade South, Highbrook, Auckland 2013, New Zealand RYOBI is a trade mark of Ryobi Limited, and is used under license

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>